TORQUE CONVERTER
A visual inspection of torque converter may reveal converter is Blue from overheating. Stator roller clutch can be checked by inserting 2 fingers into splined inner race of roller clutch and attempting to turn race in both directions. Inner race should turn freely clockwise, but should not turn or should be difficult to turn counterclockwise.
TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) | |
|---|---|---|
| Case Cover-To-Case Bolt/Stud | ||
| 10-mm | 15-20 (20-27) | |
| 13-mm | 20-23 (27-31) | |
| Case Cover-To-Driven Sprocket Support Bolt | 15-20 (20-27) | |
| Case Extension-To-Case Bolt | ||
| 10-mm | 15-20 (20-27) | |
| 13-mm | 37-40 (50-54) | |
| Case Extension-To-Case Stud | 37-40 (50-54) | |
| Case-To-Forward Clutch Support Stud | 19-20 (26-27) | |
| Coast & Forward Clutch Support Stud | 19 (26) | |
| Cooler Connector To Cooler (Case) | 15-20 (20-27) | |
| Final Drive-To-Differential Bolt | 52-56 (71-76) | |
| Flexplate Bolt | 62 (84) | |
| Manual Shaft-To-Detent Lever Nut | 20-25 (27-34) | |
| Oil Test Plug | 14 (19) | |
| Return Cooler Connector | 19-21 (26-29) | |
| Side Oil Pan-To-Case Cover Bolt | ||
| 13-mm | 15-20 (20-27) | |
| 15-mm | 37-40 (50-54) | |
| Side Oil Pan-To-Case Stud | 37-40 (50-54) | |
| INCH Lbs. (N.m) | ||
| Accumulator Housing Cover Bolt | 71-124 (8-14) | |
| Accumulator Housing-To-Channel Plate Bolt | 71-124 (8-14) | |
| Channel Plate-To-Accumulator Housing Bolt | 71-124 (8-14) | |
| Channel Plate-To-Case Bolt | 71-124 (8-14) | |
| Channel Plate-To-Case Nut | 71-124 (8-14) | |
| Detent Lever & Roller Assembly Bolt | 71-124 (8-14) | |
| Drive Sprocket Support-To-Case Bolt | 97-115 (11-13) | |
| Input Speed Sensor Bolt | 97-115 (11-13) | |
| Lower Control Valve Body-To-Channel Plate Bolt | 71-124 (8-14) | |
| Lower Oil Pan Bolt (1) | 89-106 (10-12) | |
| Oil Drain And Filler Plug | 71-124 (8-14) | |
| Oil Transfer Plate Bolt | 106 (12) | |
| Pump Assembly-To-Case Bolt | 97-115 (11-13) | |
| Pump Assembly-To-Case Cover Bolt | 97-115 (11-13) | |
| Scavenge Pump Cover-To-Body Bolt | 97-115 (11-13) | |
| Scavenge Tube-To-Case Bolt | 71-124 (8-14) | |
| Secondary Pump-To-Case Bolt | 97-115 (11-13) | |
| Secondary Pump-To-Case Cover Bolt | 97-115 (11-13) | |
| Servo Cover-To-Case Bolt | 71-124 (8-14) | |
| Spacer Plate Support-To-Channel Plate Bolt | 71-124 (8-14) | |
| Speed Sensor-To-Case Extension Bolt | 71-124 (8-14) | |
| Temperature Sensor | 30 (3.4) | |
| Upper Control Valve Body Bolt | 97-115 (11-13) | |
| Upper Control Valve Body-To-Case Cover Bolt | 97-115 (11-13) | |
| Upper Control Valve Body-To-Driven Sprocket Support Bolt | 97-115 (11-13) | |
| (1) Tighten in sequence. (Схема №39) | ||
| (1) | Tighten in sequence. (Схема №39) |
TORQUE SPECIFICATIONS
TRANSAXLE SPECIFICATIONS
| Application | End Play - In. (mm) |
|---|---|
| Final Drive | .006-.026 (.15-.65) |
| Final Drive Carrier Pinion Gears | .008-.012 (.20-.30) |
| Input Carrier Pinion Gear | .003-.035 (.08-.89) |
| Input Shaft | .004-.033 (.10-.85) |
| Reaction Carrier Pinion Gear | .004-.035 (.10-.89) |
TRANSAXLE SPECIFICATIONS