Home ReviewsRefund
Home/Mercury/Milan/Mercury Milan I (2005-2010)/Repair manual/Communication Devices/Module Configuration: Diagnosis
Contents Wiring diagrams Section: Communication Devices All sections

Module Configuration: Diagnosis Mercury Milan I

Communication Devices ~360 words

Inspection and Verification

This section provides step-by-step module configuration procedures. Carry out the Programmable Module Installation when another workshop manual section directs to carry out configuration or when DTCs from the below list are present

DTCDescriptionSourceAction
B2477Module Configuration FailureAnti-lock brake system (ABS) module Audio unit Climate controlled seat module (CCSM) Driver seat module (DSM) Instrument cluster Occupant classification sensor module Restraints control module (RCM) Smart junction box (SJB) Satellite radio receiver THX® amplifierCARRY OUT PMI. REFER to Programmable Module Installation .
B2900VIN mismatchABS module Four wheel drive (4WD) control module RCMCARRY OUT PMI. REFER to Programmable Module Installation .
P0602Powertrain Control Module Programming ErrorPowertrain control module (PCM)CARRY OUT PMI. REFER to Programmable Module Installation .
P0605Internal Control Module Read Only Memory (ROM) ErrorPCMCARRY OUT PMI. REFER to Programmable Module Installation .
P1639Vehicle ID Block Corrupted, Not ProgrammedPCMCARRY OUT PMI. REFER to Programmable Module Installation .
U0300Internal Control Module Software IncompatibilityPCM RCMCARRY OUT PMI. REFER to Programmable Module Installation .
U2050No Application PresentABS module Audio unit Climate controlled seat module DSM Driver door module (DDM) Electronic automatic temperature control (EATC) Instrument cluster Occupant classification sensor module PCM RCM SJB Satellite radio receiver THX® amplifier Transmission control module (TCM) 4WD control moduleCARRY OUT PMI. REFER to Programmable Module Installation .
U2051No Application PresentAudio unit EATC Instrument cluster Occupant classification sensor module PCM RCM THX® amplifier 4WD control moduleCARRY OUT PMI. REFER to Programmable Module Installation .

DIAGNOSTIC TROUBLE CODE (DTC) INDEX

Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is Available

Note. Following module installation, some modules require a separate learning procedure be carried out. For adaptive learning and calibration instructions, refer to the specific module removal and installation procedures.

  1. Connect the IDS and identify the vehicle as normal.
  2. From the Toolbox icon, select Module Programming and press the check mark.
  3. Select Programmable Module Installation.
  4. Select the module that is being replaced.
  5. Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
  6. Install the new module and press the check mark.
  7. Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
  8. The IDS downloads the data into the new module and displays Module Configuration Complete.
  9. Test module for correct operation.

Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is NOT Available

Note. Following module installation, some modules require a separate learning procedure be carried out. For adaptive learning and calibration instructions, refer to the specific module removal and installation procedures.

  1. Install the new module.
  2. Connect the IDS and identify the vehicle as normal.
  3. From the Toolbox icon, select Module Programming and press the check mark.
  4. Select Programmable Module Installation.
  5. Select the module that was replaced.
  6. Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
  7. Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
  8. If the data is not available, the IDS displays a screen stating to contact the As-Built Data Center. Retrieve the data from the technician service publication website at this time and press the check mark.
  9. Enter the module data and press the check mark.
  10. The IDS downloads the data into the new module and displays Module Configuration Complete.
  11. Test module for correct operation.

More articles — Module Configuration