Starting (Service Specifications): Other — Lexus LS III рестайлинг (2003-2006)

SERVICE DATA

Starter	Rated voltage and output power		12 V 2.0 kW
	No-load characteristics	Current	100 A or less at 11.5 V
	Brush length	STD	15.0 mm (0.591 in.)
	Brush length	Minimum	9.0 mm (0.354 in.)
	Spring installed load	STD	21.5 to 27.5 N (2.2 to 2.8 kgf, 4.9 to 6.2 lbf)
	Spring installed load	Minimum	12.7 N (1.3 kgf, 2.9 lbf)
	Commutator
	Diameter	STD	35.0 mm (1.378 in.)
	Diameter	Minimum	34.0 mm (1.339 in.)
	Undercut depth	STD	0.7 mm (0.028 in.)
	Undercut depth	Minimum	0.2 mm (0.008 in.)
	Circle runout	Maximum	0.05 mm (0.0020 in.)
	Yoke
	Shut coil resistance	At 20°C (68°F)	1.5 to 1.9 ohms
Generator	Rated output		12 V 100 A
	Rotor coil resistance	At 20°C (68°F)	2.1 to 2.5 ohms
	Slip ring diameter		12.8 to 14.4 mm (0.504 to 0.567 in.)
	Brush exposed length		1.5 to 11.5 mm (0.059 to 0.453 in.)
Voltage regulator	Regulating voltage		13.2 to 14.8 V

Identifying Starting & Charging Service Data

Time of change in vehicle height
	NORM HIGH position	20 to 40 seconds
	HIGH - NORM position	20 to 40 seconds
Time of target height
	4 people on the vehicle	40 to 60 seconds
	4 people out of the vehicle	10 to 30 seconds

Identifying Suspension Control System Service Data

Front wheel alignment	Vehicle height
	Except air suspension P225/55 H17	Front: B - A	105 mm (4.13 in.)
	Except air suspension P225/55 H17	Rear: D - C	91 mm (3.58 in.)
	Except air suspension 245/45 R18	Front: B - A	104 mm (4.09 in.)
	Except air suspension 245/45 R18	Rear: D - C	89 mm (3.50 in.)
	Vehicle height
	Air suspension	Front: B - A	115 mm (4.53 in.)
	Air suspension	Rear: D - C	109 mm (4.29 in.)
Front wheel alignment	Toe-in (total)		0°06' ± 12' (0.1° ± 0.2°) 1 ± 2 mm (0.04 ± 0.08 in.)
	Wheel angle
		Inside wheel	42°10' (42.2°)
		Outside wheel: Reference	36°15' (36.3°)
Except air suspension Front wheel alignment	Camber		0°05' ± 45' (-0.08° ± 0.75°)
	Camber	Right-left error	30' (0.5°) or less
	Caster		6°45' ± 45' (6.75° ± 0.75°)
	Caster	Right-left error	30' (0.5°) or less
	Steering axis inclination		9°00' ± 45' (9° ± 0.75°)
	Steering axis inclination	Right-left error	30' (0.5°) or less
Are suspension Front wheel alignment	Camber		0°15' ± 45' (-0.25° ± 0.75°)
	Camber	Right-left error	30' (0.5°) or less
	Caster		7°15' ± 45' (7.25° ± 0.75°)
	Caster	Right-left error	30' (0.5°) or less
	Steering axis inclination		9° 15' ± 45' (9.25° ± 0.75°)
	Steering axis inclination	Right-left error	30' (0.5°) or less
Front suspension	Lower ball joint turning torque		0.5 to 3.5 N.m (5 to 36 kgf.cm, 4,5 to 31 in.lbf)
Front suspension	Stabilizer bar link ball joint turning torque		0.05 to 1.98 N.m (0.5 to 20 kgf.cm, 0.4 to 17 in.lbf)

Identifying Front Suspension Service Data

A: Ground clearance of lower suspension arm No.1 bush set bolt center

B: Ground clearance of front wheel center

C: Ground clearance of rear suspension arm No.2 set bolt center

D: Ground clearance of rear wheel center

Rear wheel alignment	Toe-in (total)		0°18' ± 12' (0.3° ± 0.2°, 3 ± 2 mm, 0.12 ± 0.08 in.)
		No.2 lower suspension arm length difference
		2WD	1.5 mm (0.06 in.) or less
		4WD	1.0 mm (0.04 in.) or less
	Camber
		Air suspension	1°35' ±45' (-1.58° ± 0.75°)
		Coil suspension	1°15' ± 45' (-1.25° ± 0.75°)
		Right-left error	45' (0.75°) or less
Rear Suspension	Stabilizer link ball joint turning torque		0.05 to 0.98 N.m (0.5 to 10 kgf.cm, 0.4 to 9 in..lbf) or less

Identifying Rear Suspension Service Data

Cold tire inflation pressure	Tire size: 225/55R17 95H	Front, Rear	220 kPa (2.2 kgf/cm 2 , 31 psi)
Cold tire inflation pressure	Tire size: P245/45R18 96W	Front, Rear	230 kPa (2.3 kgf/cm 2 , 33 psi)
Tire & Wheel	Tire runout		1.4 mm (0.055 in.) or less
Tire & Wheel	Imbalance after adjustment		5.0 g (0.011 lb) or less

Identifying Tire & Wheel Service Data

Rear differential	Differential ring gear runout	Maximum	0.05 mm (0.0020 in.)
	Differential ring gear backlash	Maximum	0.08 to 0.13 mm (0.0031 to 0.0051 in.)
	Differential drive pinion runout	Maximum	0.08 mm (0.0031 in.)
	Differential drive pinion preload (at starting)	New bearing	1.5 to 2.0 N.m (15 to 21 kgf.cm, 13 to 18 in..lbf)
	Differential drive pinion preload (at starting)	Reused bearing	0.5 to 0.8 N.m (5 to 8 kgf.cm, 4.3 to 6.9 in..lbf)
	Differential side gear backlash		0 mm (0 in.)
	Total preload (at starting)		Differential drive pinion preload plus 0.46 to 1.37 N.m (4.69 to 13.97 kgf.cm, 4.07 to 12.13 in..lbf)
Rear differential (cont'd)	Differential ring gear backlash adjusting washer		3.66 mm (0.1441 in.) 3.68 mm (0.1449 in.) 3.70 mm (0.1457 in.) 3.72 mm (0.1465 in.) 3.74 mm (0.1472 in.) 3.76 mm (0.1480 in.) 3.78 mm (0.1488 in.) 3.80 mm (0.1496 in.) 3.82 mm (0.1503 in.) 3.84 mm (0.1512 in.) 3.86 mm (0.1520 in.) 3.88 mm (0.1528 in.) 3.90 mm (0.1535 in.) 3.92 mm (0.1543 in.) 3.94 mm (0.1551 in.) 3.96 mm (0.1559 In.) 3.98 mm (0.1567 in.) 4.00 mm (0.1575 in.) 4.02 mm (0.1583 in.) 4.04 mm (0.1591 in.) 4.06 mm (0.1598 in.) 4.08 mm (0.1606 in.) 4.10 mm (0.1614 in.) 4.12 mm (0.1622 in.) 4.14 mm (0.1630 in.) 4.16 mm (0.1638 in.) 4.18 mm (0.1646 in.) 4.20 mm (0.1654 in.) 4.22 mm (0.1661 in.) 4.24 mm (0.1669 in.) 4.26 mm (0.1677 in.) 4.28 mm (0.1685 in.) 4.30 mm (0.1693 in.) 4.32 mm (0.1701 in.) 4.34 mm (0.1709 in.) 4.36 mm (0.1717 in.) 4.38 mm (0.1724 in.) 4.40 mm (0.1732 in.) 4.42 mm (0.1740 in.)

Identifying Differential Service Data (1 Of 2)

Rear differential (cont'd)	Tooth contact pattern adjusting washer	No.
		87	1.87 mm (0.0736 in.)
		88	1.88 mm (0.0740 in.)
		89	1.89 mm (0.0744 in.)
		90	1.90 mm (0.0748 in.)
		91	1.91 mm (0.0752 in.)
		92	1.92 mm (0.0756 in.)
		93	1.93 mm (0.0760 in.)
		94	1.94 mm (0.0764 in.)
		95	1.95 mm (0.0768 in.)
		96	1.96 mm (0.0772 in.)
		97	1.97 mm (0.0776 in.)
		98	1.98 mm (0.0780 in.)
		99	1.99 mm (0.0784 in.)
		00	2.00 mm (0.0788 in.)
		01	2.01 mm (0.0791 in.)
		02	2.02 mm (0.0795 in.)
		03	2.03 mm (0.0799 in.)
		04	2.04 mm (0.0803 in.)
		05	2.05 mm (0.0807 in.)
		06	2.06 mm (0.0811 in.)
		07	2.07 mm (0.0815 in.)
		08	2.08 mm (0.0819 in.)
		09	2.09 mm (0.0823 in.)
		10	2.10 mm (0.0827 in.)
		11	2.11 mm (0.0831 in.)
		12	2.12 mm (0.0835 in.)
		13	2.13 mm (0.0839 in.)
		14	2.14 mm (0.0843 in.)
		15	2.15 mm (0.0846 in.)
		16	2.16 mm (0.0850 in.)
		17	2.17 mm (0.0854 in.)
		18	2.18 mm (0.0858 in.)
		19	2.19 mm (0.0862 in.)
		20	2.20 mm (0.0866 in.)
		21	2.21 mm (0.0870 in.)
		22	2.22 mm (0.0874 in.)
		23	2.23 mm (0.0878 in.)
		24	2.24 mm (0.0882 in.)
		25	2.25 mm (0.0886 in.)
		26	2.26 mm (0.0890 in.)
		27	2.27 mm (0.0894 in.)
		28	2.28 mm (0.0898 in.)

Identifying Differential Service Data (2 Of 2)