Inspection and Verification
- Verify the customer concern.
- Visually inspect for obvious signs of damage and system integrity. Visual Inspection Mechanical Electrical Hydraulic Damaged shift mechanism/linkages Damaged automatic transmission casing Check the transmission selector lever cable for correct adjustment. Refer to «Selector Lever Cable Adjustment»(ref-312593-S11099770522009041400000) article. Blown fuse(s) Damaged, loose or corroded connectors Wiring harness Fluid level too high/low Poor condition of fluid Fluid leak
- If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
- If the cause is not visually evident check for diagnostic trouble codes (DTCs) and refer to «DTC Index»(ref-312552-S10096007582009041400000) .
DTC Index
| CAUTION | When probing connectors to take measurements in the course of the pinpoint tests, use the adaptor kit, part number 3548-1358-00. |
Note. If the control module/transmission is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval program is in operation, prior to the installation of a new module/transmission.
Note. Generic scan tools may not read the codes listed, or may read only five digit codes. Match the five digits from the scan tool to the first five digits of the seven digit code listed to identify the fault (the last two digits give additional information read by the manufacturer approved diagnostic system).
Note. When performing electrical voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal places, and with an up-to-date calibration certificate. When testing resistance, always take the resistance of the DMM leads into account.
Note. Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
Note. Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
Note. If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.
| DTC | Description | Possible Cause | Action |
|---|---|---|---|
| P071100 | Transmission Fluid Temperature Sensor A Circuit Range/Performance | Transmission fluid temperature sensor pins short circuit or fluid temperature rise rate too low | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P093800 | Transmission fluid temperature sensor range/performance | Transmission fluid temperature compared with module temperature fault | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P071300 | Transmission fluid temperature sensor circuit high input | Both transmission fluid temperature sensor pins signal voltage too high | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P071200 | Transmission fluid temperature sensor circuit low input | Both transmission fluid temperature sensor pins signal voltage too low | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P071000 | Transmission fluid temperature sensor circuit open | Open circuit transmission fluid temperature sensor | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P070000 | Transmission control system (MIL Request) | No wheel speed information on CAN TCM failure | Check for wheel speed related DTCs and refer to DTC Index . Refer to Anti-Lock Control - Stability Assist article. Install a new transmission control module and main control valve body assembly, refer to DTC Index and Transmission Control Module (TCM) and Main Control Valve Body . |
| P062F00 | Internal control module EEPROM error | EEPROM communication error | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P060100 | Internal control module memory checksum error | Software error TCM failure | Re-configure the transmission using the manufacturer approved diagnostic system, clear DTC and re-test. If DTC remains, Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P072000 | Output shaft speed sensor circuit | Transmission output shaft speed sensor circuit short to power | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P072122 | Output shaft speed sensor circuit range/performance | Transmission output shaft speed sensor signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P021900 | Engine overspeed condition | Engine speed signal received over CAN is too high | Check engine management DTCs and refer to DTC Index . Refer to Electronic Engine Controls article. |
| P071700 | Turbine/input shaft speed sensor A circuit - short to power | Turbine/input shaft speed sensor A circuit - short to power | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P071600 | Turbine/input shaft speed sensor A circuit failure or sensor out of range | Circuit short to ground, power, open circuit or signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P089700 | Transmission fluid requires replacement due to excessive running time at maximum operating temperatures | Low transmission fluid level Blocked or damaged transmission fluid cooler | Drain and re-fill transmission fluid to correct level. See Transmission Fluid Drain and Refill . Check for blocked or damaged transmission fluid cooler |
| P012100 | Throttle/pedal position sensor A circuit range/performance | Pedal assembly faulty or does not have full range of movement | Ensure the accelerator pedal is free from restriction, check 'Accelerator Pedal Position received on CAN' datalogger signal (should be 100% when pedal fully depressed). Check for throttle/pedal position related DTCs and refer to DTC Index . Refer to Electronic Engine Controls article. |
| P070500 | Transmission range sensor A circuit (PRNDL input) | Signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P178300 | Transmission over temperature condition | Low transmission fluid level Blocked or damaged transmission fluid cooler | Drain and re-fill transmission fluid to correct level. See Transmission Fluid Drain and Refill . Check for blocked or damaged transmission fluid cooler |
| P056200 | TCM supply voltage low | Low battery charge Harness fault | Ensure battery is in a fully charged and serviceable condition, refer to the battery care manual. Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Also check for additional DTCs that could be associated to loss of power or ground feed and refer to DTC Index |
| P065700 | Actuator supply voltage A - open circuit, range/performance | Signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P065900 | Actuator supply voltage A circuit high | Actuator (pressure control valves etc.) supply voltage short to power | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P065800 | Actuator supply voltage A circuit low | Actuator (pressure control valves etc.) supply voltage short to ground | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P061300 | TCM processor | Microprocessor control failure | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P074100 | Torque converter clutch solenoid circuit range/performance or stuck off | Signal out of range | Install a new torque converter, refer to DTC Index . See Transmission . |
| P096200 | Pressure control solenoid A control circuit low | Pressure control solenoid A short to ground | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P096014 | Pressure control solenoid A control circuit low | Pressure control solenoid A short to ground, open circuit | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P074800 | Pressure control solenoid A current out of range | Signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P096300 | Pressure control solenoid A control circuit high | Pressure control solenoid A control circuit short to power | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P096013 | Pressure control solenoid A open circuit | Pressure control solenoid A open circuit | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P096600 | Pressure control solenoid B control circuit low | Pressure control solenoid B short to ground | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P096414 | Pressure control solenoid B control circuit low | Pressure control solenoid B short to ground, open circuit | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P077800 | Pressure control solenoid B current out of range | Signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P096700 | Pressure control solenoid B control circuit high | Pressure control solenoid B control circuit short to power | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P096413 | Pressure control solenoid B open circuit | Pressure control solenoid B open circuit | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P097000 | Pressure control solenoid C control circuit low | Pressure control solenoid C short to ground | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P096814 | Pressure control solenoid C control circuit low | Pressure control solenoid C short to ground, open circuit | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P079800 | Pressure control solenoid C current out of range | Signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P097100 | Pressure control solenoid C control circuit high | Pressure control solenoid C control circuit short to power | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P096813 | Pressure control solenoid C open circuit | Pressure control solenoid C open circuit | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P272000 | Pressure control solenoid D control circuit low | Pressure control solenoid D short to ground | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P271814 | Pressure control solenoid D control circuit low | Pressure control solenoid D short to ground, open circuit | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P271600 | Pressure control solenoid D current out of range | Signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P272100 | Pressure control solenoid D control circuit high | Pressure control solenoid D control circuit short to power | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P271813 | Pressure control solenoid D control circuit open circuit | Pressure control solenoid D control circuit open circuit | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P272900 | Pressure control solenoid E control circuit low | Pressure control solenoid E short to ground | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P272714 | Pressure control solenoid E control circuit low | Pressure control solenoid E short to ground, open circuit | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P272500 | Pressure control solenoid E current out of range | Signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P273000 | Pressure control solenoid E control circuit high | Pressure control solenoid E control circuit short to power | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P272713 | Pressure control solenoid E control circuit open circuit | Pressure control solenoid E control circuit open circuit | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P276400 | Pressure control solenoid F control circuit low | Pressure control solenoid F short to ground | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P276100 | Pressure control solenoid F control circuit low | Pressure control solenoid F short to ground, open circuit | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P275900 | Pressure control solenoid F current out of range (high) | Signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P276200 | Pressure control solenoid F current out of range (low) | Signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P276300 | Pressure control solenoid F control circuit high | Pressure control solenoid F control circuit short to power | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P074000 | Pressure control solenoid F control circuit open circuit | Pressure control solenoid F control circuit open circuit | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P075200 | Solenoid valve A control circuit low | Solenoid valve A control circuit short to ground | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P075114 | Solenoid valve A control circuit low | Solenoid valve A control circuit short to ground, open circuit | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P075300 | Solenoid valve A control circuit high | Solenoid valve A control circuit short to power | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P075113 | Solenoid valve A control circuit open circuit | Solenoid valve A control circuit open circuit | Install a new transmission control module and main control valve body assembly, refer to DTC Index . See Transmission Control Module (TCM) and Main Control Valve Body . |
| P073000 | Slip too high between input and output shaft speeds in any gear | Low transmission fluid level Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P073100 | Slip too high between input and output shaft speeds in 1st gear | Low transmission fluid level Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P073200 | Slip too high between input and output shaft speeds in 2nd gear | Low transmission fluid level Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P073300 | Slip too high between input and output shaft speeds in 3rd gear | Low transmission fluid level Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P073400 | Slip too high between input and output shaft speeds in 4th gear | Low transmission fluid level Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P073500 | Slip too high between input and output shaft speeds in 5th gear | Low transmission fluid level Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P072900 | Slip too high between input and output shaft speeds in 6th gear | Low transmission fluid level Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P078000 | Shift monitoring fault - input/output shaft speed ratio out of range during a shift (any gear). Relevant clutch does not open or close | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P078162 | 1-2 Shift - Comparison of input and output speed during a shift 1 to 2 (relevant clutch does not open or close) | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P078164 | 1-2 Shift - Comparison of input and output speed during a shift 1 to 2 (relevant clutch does not open or close) | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P078262 | 2-3 Shift - Comparison of input and output speed during a shift 2 to 3 (relevant clutch does not open or close) | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P078264 | 2-3 Shift - Comparison of input and output speed during a shift 2 to 3 (relevant clutch does not open or close) | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P078362 | 3-4 Shift - Comparison of input and output speed during a shift 3 to 4 (relevant clutch does not open or close) | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P078364 | 3-4 Shift - Comparison of input and output speed during a shift 3 to 4 (relevant clutch does not open or close) | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P078462 | 4-5 Shift - Comparison of input and output speed during a shift 4 to 5 (relevant clutch does not open or close) | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P078464 | 4-5 Shift - Comparison of input and output speed during a shift 4 to 5 (relevant clutch does not open or close) | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P082962 | 5-6 Shift - Comparison of input and output speed during a shift 5 to 6 (relevant clutch does not open or close) | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P082964 | 5-6 Shift - Comparison of input and output speed during a shift 5 to 6 (relevant clutch does not open or close) | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P078123 | 2-1 Shift - Comparison of input and output speeds during gear shift 2 to 1. Clutch does not open | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P078200 | 3-2 Shift - Comparison of input and output speeds during gear shift 3 to 2. Clutch does not open | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P078300 | 4-3 Shift - Comparison of input and output speeds during gear shift 4 to 3. Clutch does not open | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P078323 | 4-3 Shift - Comparison of input and output speeds during gear shift 4 to 3. Clutch does not open | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P078423 | 5-4 Shift - Comparison of input and output speeds during gear shift 5 to 4. Clutch does not open | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P072164 | Output speed against turbine speed and wheel speed fault | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new Transmission Control Module. Refer to DTC Index and See Transmission Control Module (TCM) and Main Control Valve Body . |
| P082923 | 6-5 Shift - Comparison of input and output speeds during gear shift 6 to 5. Clutch does not open | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P056100 | Power supply voltage out of range when engine running | Low battery charge Harness fault | Ensure battery is in a fully charged and serviceable condition, refer to the battery care manual. Check 'Battery Voltage at TCM' datalogger signal. Check for DTCs that could be associated to loss of power or ground feeds at TCM and refer to DTC Index |
| P085000 | Starter inhibit signal fault | Park/neutral switch input circuit fault TCM failure | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. After pinpoint test complete, re-test and if fault remains install a new transmission control module and main control valve body assembly, refer to DTC Index |
| P060500 | EPROM/FLASH checksum error | Software fault TCM failure | Re-configure the TCM using the manufacturer approved diagnostic system, re-test. If DTC remains, install a new transmission control module and main control valve body assembly, refer to DTC Index |
| P066900 | TCM internal temperature high | Signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index |
| P066800 | TCM internal temperature low | Signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index |
| P064300 | Sensor supply voltage fault high | Signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index |
| P064200 | Sensor supply voltage fault low | Signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index |
| P060300 | Loss of data in RAM fault | Battery discharged Transit relay installed Battery isolation device installed Harness fault | Ensure battery is fully charged and in a serviceable condition, refer to the battery care manual. Remove transit relay or any battery isolation device installed. Clear DTCs and re-test, if DTC remains check for additional DTCs and refer to DTC Index |
| P082600 | Manual shift CAN request error | Shift paddles not working. Instrument cluster LIN/CAN gateway failure Shift paddle(s) failure | Check availability of speed control. If speed control is also inoperative, check instrument cluster for related DTCs and refer to DTC Index . Refer to Instrument Cluster article. If speed control is available, check the shift paddle functionality using the datalogger application on the manufacturer approved diagnostic system |
| P061300 | Micro controller component faults | Signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index |
| P050000 | Vehicle speed signal not detected | Wheel speed sensor fault | Check anti-lock control - stability assist module and ECM for wheel speed sensor related DTCs and refer to DTC Index . Refer to Anti-Lock Control - Stability Assist and Electronic Engine Controls article. |
| P050100 | Vehicle speed sensor A range/performance | Wheel speed sensor fault | Check anti-lock control - stability assist module and ECM for wheel speed sensor related DTCs and refer to DTC Index . Refer to Anti-Lock Control - Stability Assist and Electronic Engine Controls article. |
| P056300 | Battery voltage too high when engine running | High battery charge, alternator fault | Check 'Battery Voltage at TCM' datalogger signal. Check for alternator/over charging related DTCs and refer to DTC Index |
| P072127 | Output shaft speed out of range | Signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index |
| P073600 | Slip too high between input and output shaft speeds in reverse gear | Low transmission fluid level Blocked transmission fluid cooler Worn clutches | Check and set transmission fluid to correct level. See Transmission Fluid Level Check . Ensure transmission fluid cooler is free from restriction. Clear DTC and re-test. If DTC remains, install a new transmission. Refer to DTC Index |
| P061B61 | TCM positive torque signal not valid | Signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index |
| P061B65 | TCM positive torque signal not valid | Signal out of range | Install a new transmission control module and main control valve body assembly, refer to DTC Index |
| U040186 | Invalid data received from ECM | Engine speed value invalid | Check ECM for DTCs and refer to DTC Index . Refer to Electronic Engine Controls article. |
| U030055 | Internal control module software incompatibility | Mis-match between vehicle and TCM software levels | Re-configure the TCM with the latest level software using the manufacturer approved diagnostic system |
| U000188 | High speed CAN communication Bus | Vehicle CAN Bus off condition | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system |
| U202386 | Fault received from external node | Engine torque information | Check ECM for DTCs and refer to DTC Index . Refer to Electronic Engine Controls article. |
| U010387 | Lost communications with gear selector lever | Missing message from gear selector lever | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system |
| U015587 | Lost communication with instrument cluster | CAN timeout instrument cluster | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system |
| U012887 | Lost communication with parking brake module | CAN timeout parking brake module | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system |
| U010087 | Lost communication with ECM | Missing message from ECM | Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system |
| U012287 | Lost communication with stability control module | CAN timeout stability control module (instrument cluster Off Bus) | Check instrument cluster for DTCs and refer to DTC Index |
| U041686 | Invalid data received from Anti-lock control - stability assist module | Brake information | Check the anti-lock - stability assist system for DTCs and refer to the DTC Index . Refer to Anti-Lock Control - Stability Assist article. |
| U30004A | Control module | Mis-match between configuration data and calibrated data values | Re-configure the TCM using the manufacturer approved diagnostic system |
| U040462 | Invalid data received from the gear selector lever - implausible position | Gear selector cable out of adjustment. Gear selector lever assembly fault | Check gear selector cable adjustment. Refer to Selector Lever Cable Adjustment article. |
| U040464 | Invalid data received from the gear selector lever - implausible signal | Gear selector cable out of adjustment. Gear selector lever assembly fault | Check gear selector cable adjustment. Refer to Selector Lever Cable Adjustment article. |
| U040486 | Invalid data received from the gear selector lever - general failure | Gear selector cable out of adjustment. Gear selector lever assembly fault | Check gear selector cable adjustment. Refer to Selector Lever Cable Adjustment article. |