DIAGNOSTIC TROUBLE CODE INDEX
| DTC | Description |
|---|---|
| DTC U1260 | SCP network SCP + circuit fault |
| DTC U1261 | SCP network SCP - circuit fault |
| DTC U1262 | SCP network circuit fault |
| DTC U1262 | SCP network circuit fault |
| DTC U1341 | SCP vehicle speed message invalid or not available |
| DTC U1900 | CAN communication fault |
| DTC U1900 | CAN communication fault |
| DTC U1901 | Local CAN network (steering angle sensor, yaw rate and lateral acceleration sensor) communication fault |
| DTC U2003 | CD autochanger not responding on D2B network |
| DTC U2008 | CPCM not responding on D2B network |
| DTC U2012 | CAN Communication fault |
| DTC U2019 | VACM not responding on D2B network |
| DTC U2023 | CAN fault message received from other network module(s) |
| DTC U2202 | CAN Invalid configuration data received |
| DTC U2501 | CAN ECM "token" missing |
| DTC U2502 | CAN TCM "token" missing |
| DTC U2503 | CAN IC "token" missing |
| DTC U2504 | CAN DSCCM "token" missing |
| DTC U2515 | CAN Adaptive speed control message missing |
| DTC U2515 | CAN ASCCM message missing |
| DTC U2516 | CAN TCM message missing |
| DTC U2516 | CAN not responding |
| DTC U2518 | CAN A/CCM message missing |
| DTC U2520 | CAN IC module missing |
| DTC U2521 | CAN DSCCM module missing |
| DTC U2521 | DSCCM message missing |
| DTC U2522 | CAN TCM module missing |
| DTC U2522 | CAN TCM module missing |
| DTC U2522 | TCM message missing |
| DTC U2523 | CAN ECM module missing |
| DTC U2523 | CAN ECM module missing |
| DTC U2523 | CAN ECM message missing |
| DTC U2527 | Local CAN network (steering angle sensor, yaw rate and lateral acceleration sensor) transmit fault |
| DTC U2601 | D2B "wake-up" circuit fault |
| DTC U2601 | D2B "wake-up" circuit fault |
| DTC U2601 | D2B "wake-up" circuit fault |
| DTC U2601 | D2B "wake-up" circuit fault |
| DTC U2602 | D2B network "ring" incomplete (fault reported) |
| DTC U2603 | D2B network "ring" incomplete (fault not reported) |
| DTC U2604 | D2B network "ring" incomplete (corrupted fault report) |
| DTC U2605 | Audio unit unable to initialize it's address |
| DTC U2606 | D2B slave module unable to initialize it's address |
| DTC U2607 | D2B slave module switched into bypass mode |
| DTC U2609 | D2B "wake-up" signal out of specification |
| DTC U2609 | D2B "wake-up" signal out of specification |
| DTC U2609 | D2B "wake-up" signal out of specification |
| DTC U2609 | D2B "wake-up" signal out of specification |
| DTC U2610 | D2B network "position status report" not received |
| DTC U2610 | D2B network "position status report" not received |
| DTC U2610 | D2B network "position status report" not received |
| DTC U2611 | D2B network "alarm clear command" not received |
| DTC U2611 | D2B network "alarm clear command" not received |
| DTC U2611 | D2B network "alarm clear command" not received |
| DTC U2613 | NCM not responding on D2B network |
| DTC U2614 | Power amplifier not responding on D2B network |
DIAGNOSTIC TROUBLE CODE INDEX
CM
DSCM