Home ReviewsRefund
Home/Honda/Accord/Honda Accord V (1993-1998)/Repair manual/Mechanical/2.2L 4-CYL Engine: Specifications
Contents Wiring diagrams Section: Mechanical All sections

2.2L 4-CYL Engine: Specifications Honda Accord V

Mechanical

Crankcase Capacity

See CRANKCASE CAPACITIES .

ApplicationQts. (L)
F22B1
Oil Change (1)4.5 (4.3)
Engine Overhaul5.9 (5.6)
F22B2
Oil Change (1)4.0 (3.8)
Engine Overhaul5.2 (4.9)
(1) Includes oil filter.
(1)Includes oil filter.

CRANKCASE CAPACITIES

GENERAL SPECIFICATIONS

ApplicationSpecification
Displacement132 Cu. In. (2.2L)
Bore3.35" (85.0 mm)
Stroke3.74" (95.0 mm)
Compression Ratio8.8:1
Fuel SystemMFI
Horsepower @ RPM
F22B1 Engine145 @ 5500
F22B2 Engine130 @ 5300
Torque Ft. Lbs. @ RPM
F22B1 Engine147 @ 4500
F22B2 Engine139 @ 4200

GENERAL SPECIFICATIONS

CRANKSHAFT, MAIN & CONNECTING ROD BEARINGS SPECIFICATIONS

ApplicationIn. (mm)
Crankshaft
End Play
Standard0.004-0.014 (0.10-0.35)
Service Limit0.018 (0.45)
Runout
Standard0.0012 (0.030)
Service Limit0.0016 (0.040)
Main Bearings
Journal Diameter
No. 11.9679-1.9688 (49.984-50.008)
No. 21.9676-1.9685 (49.976-50.000)
No. 31.9674-1.9683 (49.972-49.996)
No. 41.9679-1.9688 (49.984-50.008)
No. 51.9680-1.9690 (49.988-50.012)
Journal Out-Of-Round
Standard0.000197 (0.005)
Service Limit0.000234 (0.006)
Journal Taper
Standard0.000197 (0.005)
Service Limit0.000234 (0.006)
Oil Clearance
No. 1
Standard0.0005-0.0015 (0.013-0.037)
Service Limit0.002 (0.05)
No. 2 Journal
Standard0.0008-0.0018 (0.021-0.045)
Service Limit0.0020 (0.050)
No. 3 Journal
Standard0.0010-0.0019 (0.025-0.049)
Service Limit0.0022 (0.055)
No. 4 Journal
Standard0.0005-0.0015 (0.013-0.037)
Service Limit0.0020 (0.050)
No. 5 Journal
Standard0.0004-0.0013 (0.009-0.033)
Service Limit0.0016 (0.040)
Connecting Rod Bearings
Journal Diameter1.8888-1.8898 (47.976-48.001)
Journal Out-Of-Round
Standard0.000197 (0.0050)
Service Limit0.000234 (0.0060)
Journal Taper
Standard0.000197 (0.0050)
Service Limit0.000234 (0.0060)
Oil Clearance
Standard0.0008-0.0019 (0.021-0.049)
Service Limit0.0022 (0.055)

CRANKSHAFT, MAIN & CONNECTING ROD BEARINGS

CONNECTING ROD SPECIFICATIONS

ApplicationIn. (mm)
Bore Diameter
Large End Bore2.01 (51.0)
Small End (Pin) Bore0.8649-0.8654 (21.968-21.981)
Piston Pin-To-Connecting Rod Clearance0.0005-0.0013 (0.013-0.032)
Side Play
Standard0.006-0.012 (0.15-0.30)
Service Limit0.016 (0.40)

CONNECTING ROD

OIL PUMP SPECIFICATIONS

ApplicationSpecification
Inner Rotor-To-Outer Rotor Radial Clearance
Standard0.001-0.006" (0.02-0.16 mm)
Service Limit0.008" (0.20 mm)
Pump Housing-To-Rotor Axial Clearance
Standard0.001-0.003" (0.02-0.08 mm)
Service Limit0.005" (0.13 mm)
Pump Housing-To-Outer Rotor Radial Clearance
Standard0.004-0.007" (0.10-0.19 mm)
Service Limit0.008" (0.20 mm)
Minimum Oil Pressure At 176°F (80°C)
At Idle10 psi. (0.7 kg/cm 2 )
At 3000 RPM50 psi. (3.5 kg/cm 2 )

OIL PUMP SPECIFICATIONS

PISTONS, PINS & RINGS SPECIFICATIONS

ApplicationIn. (mm)
Piston
Piston-To-Cylinder Clearance
Standard0.0008-0.0016 (0.020-0.040)
Service Limit0.0020 (0.050)
Piston Diameter (1)
No Letter, A Or I Piston
Standard3.3457-3.3461 (84.980-84.990)
Service Limit3.3453 (84.970)
B Or II Piston
Standard3.3453-3.3457 (84.970-84.980)
Service Limit3.3449 (84.960)
Piston Pin
Outer Diameter0.8659-0.8661 (21.994-22.000)
Pin-To-Piston Clearance0.0004-0.0009 (0.010-0.022)
Rings
Top Ring
End Gap
Standard0.008-0.014 (0.20-0.35)
Service Limit0.024 (0.60)
Side Clearance
Standard0.0014-0.0024 (0.035-0.060)
Service Limit0.005 (0.13)
2nd Ring
End Gap
Standard0.016-0.022 (0.40-0.55)
Service Limit0.028 (0.70)
Side Clearance
Standard0.0012-0.0022 (0.030-0.055)
Service Limit0.005 (0.13)
Oil Ring
End Gap0.008-0.028 (0.20-0.70)
Service Limit0.031 (0.80)
(1) Measure piston skirt diameter 0.83" (21.0 mm) from bottom of skirt.
(1)Measure piston skirt diameter 0.83" (21.0 mm) from bottom of skirt.

PISTONS, PINS & RINGS

CYLINDER BLOCK SPECIFICATIONS

ApplicationIn. (mm)
Cylinder Bore
No Letter, A Or I Block (1)
Standard Diameter3.3469-3.3472 (85.010-85.020)
Service Limit3.3492 (85.070)
B Or II Block (1)
Standard Diameter3.3465-3.3469 (85.000-85.010)
Service Limit3.3492 (85.070)
Reboring Limit0.02 (0.5)
Maximum Taper0.002 (0.05)
(1) Letters or bars have been stamped on end of cylinder block above water pump.
(1)Letters or bars have been stamped on end of cylinder block above water pump.

CYLINDER BLOCK

ROCKER ARM & ROCKER ARM SHAFT SPECIFICATIONS

ApplicationIn. (mm)
Rocker Arm-To-Shaft Clearance
F22B1
Intake
Standard0.0010-0.0026 (0.025-0.067)
Service Limit0.0031 (0.080)
Exhaust
Standard0.0007-0.0021 (0.018-0.054)
Service Limit0.0031 (0.080)
F22B2
Intake
Standard0.0007-0.0020 (0.017-0.050)
Service Limit0.0031 (0.080)
Exhaust
Standard0.0007-0.0021 (0.018-0.054)
Service Limit0.0031 (0.080)

ROCKER ARM & ROCKER ARM SHAFT

VALVES & VALVE SPRINGS SPECIFICATIONS

ApplicationIn. (mm)
Intake Valves
Face Angle(1)
Head Diameter
F22B11.335-1.343 (33.90-34.10)
F22B21.256-1.264 (31.90-32.10)
Overall Length
F22B14.522-4.533 (114.85-115.15)
F22B24.365-4.377 (110.88-111.18)
Stem Diameter
Standard0.2159-0.2163 (5.485-5.495)
Service Limit0.2148 (5.455)
Seat Margin
Standard0.033-0.045 (0.85-1.15)
Service Limit0.026 (0.65)
Valve Stem Installed Height (2)
F22B1
Standard1.8405-1.8720 (46.75-47.55)
Service Limit1.9212 (48.80)
F22B2
Standard1.8929-1.9244 (48.08-48.88)
Service Limit1.9342 (49.13)
Exhaust Valves
Face Angle(1)
Head Diameter1.138-1.146 (28.90-29.10)
Overall Length
F22B14.264-4.272 (108.30-108.50)
F22B24.604-4.624 (116.95-117.45)
Stem Diameter
Standard0.2146-0.2150 (5.450-5.460)
Service Limit0.2134 (5.420)
Seat Margin
Standard0.041-0.053 (1.05-1.35)
Service Limit0.037 (0.95)
Valve Stem Installed Height (2)
F22B1
Standard1.838-1.869 (46.75-47.55)
Service Limit1.879 (47.73)
F22B2
Standard1.974-2.006 (50.15-50.95)
Service Limit2.016 (51.20)
Valve Spring Free Length
Intake
F22B12.011 (51.08)
F22B2
Except Associated Manufactured2.1031 (53.420)
Associated Manufactured2.1579 (54.810)
Exhaust
F22B12.188 (55.58)
F22B2
Except Associated Manufactured2.1519 (54.660)
Associated Manufactured2.2157 (56.280)
(1) Valve face angle is 45°. (2) Measure from tip of installed valve stem to spring seat surface.
(1)Valve face angle is 45°.
(2)Measure from tip of installed valve stem to spring seat surface.

VALVES & VALVE SPRINGS

CYLINDER HEAD SPECIFICATIONS

ApplicationIn. (mm)
Cylinder Head
Height3.935-3.939 (99.95-100.05)
Cylinder Head Warpage
Serviceable Warpage0.002-0.008 (0.05-0.20)
Maximum Warpage Limit (1)0.008 (0.20)
Valve Seats
Intake Valve
Seat Angle(2)
Seat Width (3)0.049-0.061 (1.25-1.55)
Exhaust Valve
Seat Angle(2)
Seat Width (3)0.049-0.061 (1.25-1.55)
Valve Guide (Intake Valve)
Inner Diameter
Standard0.2171-0.2177 (5.515-5.530)
Service Limit.0.219 (5.55)
Installed Height
F22B10.8346-0.8740 (21.200-22.200)
F22B20.9252-0.9646 (23.500-24.500)
Valve Stem-To-Guide Clearance (4)
Standard0.0008-0.0018 (0.020-0.045)
Service Limit0.0031 (0.080)
Valve Stem-To-Guide Clearance (5)
Standard0.0016-0.0035 (0.040-0.090)
Service Limit0.0063 (0.160)
Valve Guide (Exhaust Valve)
Inner Diameter
Standard0.2171-0.2177 (5.515-5.530)
Service Limit0.219 (5.55)
Valve Guide Installed Height
F22B10.8122-0.8516 (20.630-21.630)
F22B20.5827-0.6220 (14.800-15.800)
Valve Stem-To-Guide Clearance (4)
Standard0.0022-0.0031 (0.055-0.080)
Service Limit0.0047 (0.120)
Valve Stem-To-Guide Clearance (5)
Standard0.0043-0.0063 (0.110-0.160)
Service Limit0.0094 (0.240)
(1) Maximum warpage limit for resurfacing head based on specified cylinder height. (2) Valve seat angle is 45° (3) Maximum service limit is 0.079" (2.00 mm). (4) Caliper method of valve stem-to-guide clearance measurement. (5) Wobble method of checking valve stem-to-guide clearance measurement.
(1)Maximum warpage limit for resurfacing head based on specified cylinder height.
(2)Valve seat angle is 45°
(3)Maximum service limit is 0.079" (2.00 mm).
(4)Caliper method of valve stem-to-guide clearance measurement.
(5)Wobble method of checking valve stem-to-guide clearance measurement.

CYLINDER HEAD

CAMSHAFT SPECIFICATIONS

ApplicationIn. (mm)
Camshaft Total Runout
Standard0.0012 (0.030)
Service Limit0.0016 (0.040)
End Play
Standard0.002-0.006 (0.05-0.15)
Service Limit0.020 (0.50)
Lobe Height
F22B1
Intake
Primary1.4872 (37.775)
Mid1.5640 (39.725)
Secondary1.3575 (34.481)
Exhaust1.5105 (38.366)
F22B2
Intake1.5168 (38.526)
Exhaust1.5267 (38.778)
Camshaft-To-Holder Oil Clearance (1)
Standard0.0020-0.0035 (0.050-0.089)
Service Limit0.006 (0.15)
(1) If camshaft-to-holder oil clearance is not within specification check camshaft total runout. If camshaft total runout is within specification replace cylinder head. If runout is not within specification replace camshaft and recheck oil clearance. If oil clearance is still not within specification, replace cylinder head also.
(1)If camshaft-to-holder oil clearance is not within specification check camshaft total runout. If camshaft total runout is within specification replace cylinder head. If runout is not within specification replace camshaft and recheck oil clearance. If oil clearance is still not within specification, replace cylinder head also.

CAMSHAFT

BALANCER SHAFTS SPECIFICATIONS

ApplicationIn. (mm)
Journal Diameter
No. 1
Front Shaft
Standard1.6820-1.6824 (42.722-42.734)
Service Limit1.6815 (42.710)
Rear Shaft
Standard0.8243-0.8248 (20.938-20.950)
Service Limit0.8236 (20.920)
No. 2 (Front & Rear Shafts)
Standard1.5241-1.5246 (38.712-38.724)
Service Limit1.5236 (38.700)
No. 3 (Front & Rear Shafts)
Standard1.3670-1.3675 (34.722-34.734)
Service Limit1.3665 (34.710)
Journal Taper0.0002 (0.005)
Shaft Bearing Inner Diameter
No. 1 Front Journal
Standard1.6850-1.6858 (42.800-42.820)
Service Limit1.6862 (42.830)
No. 1 Rear Journal (1)
Standard0.8268-0.8273 (21.000-21.013)
Service Limit0.8276 (21.020)
No. 2 Front & Rear Journals
Standard1.5276-1.5283 (38.800-38.820)
Service Limit1.5287 (38.830)
No. 3 Front & Rear Journals
Standard1.3701-1.3709 (34.800-34.820)
Service Limit1.3713 (34.830)
End Play
Front Shaft0.0039-0.0157 (0.100-0.400)
Rear Shaft0.0016-0.0059 (0.040-0.150)
Runout (Maximum)
Standard0.0008 (0.020)
Service Limit0.0012 (0.030)
Shaft-To-Bearing Oil Clearance
No. 1 Front, No. 3 Front & Rear Journals
Standard0.0026-0.0039 (0.066-0.098)
Service Limit0.0047 (0.12)
No. 1 Rear Journal
Standard0.0020-0.0030 (0.050-0.075)
Service Limit0.0035 (0.090)
No. 2 Front & Rear Journals
Standard0.0030-0.0043 (0.076-0.108)
Service Limit0.0051 (0.13)
(1) Rear shaft No. 1 bearing located in oil pump housing. Replace oil pump housing if bearing diameter not within specification or bearing is worn, damaged or discolored.
(1)Rear shaft No. 1 bearing located in oil pump housing. Replace oil pump housing if bearing diameter not within specification or bearing is worn, damaged or discolored.

BALANCER SHAFTS

TORQUE SPECIFICATIONS

ApplicationFt. Lbs. (N.m)
A/C Compressor
A/C Compressor-To-Bracket 8-mm Bolts16 (22)
Bracket-To-Engine 10-mm Nuts/Bolts36 (49)
A/T Or ATTS Cooler Pipes Bracket 10-mm Bolt33 (45)
A/T Shift Cable
Cable Cover 8-mm Bolts13 (18)
Shift Control Lever-To-Shaft 6-mm Bolt10 (14)
Balancer (Front) Shaft Pulley Bolt22 (30)
Balancer Gear Case Nuts/Bolts18 (24)
Balancer Shaft Maintenance Hole Sealing Bolt22 (30)
Balancer Shaft Retainer Bolts14 (19)
Ball Joint Castle Nut36-43 (49-58)
Battery Base & Bracket
6-mm Bolts(1)
8-mm Bolts16 (22)
Belt Tensioner Adjuster Nut32 (44)
Camshaft Holders & Holder Plate Bolts
6-mm Bolts(1)
8-mm Bolts16 (22)
Camshaft Pulley Bolt27 (37)
Center Support Beam To-Frame37 (50)
Connecting Rod Cap Nut34 (46)
Crankshaft Main Bearing Cap/Bridge Bolts
Stage 122 (30)
Stage 254 (73)
Crankshaft Pulley Bolt181 (245)
Cylinder Head Bolt
Stage 129 (39)
Stage 251 (69)
Stage 372 (98)
Distributor Bolts13 (18)
Drive Plate (A/T)55 (74)
Engine Coolant Side Drain Plug61 (83)
Engine Mounts
Center Beam-To-Rear Beam 10-mm Bolts37 (50)
Front Beam-To-Frame 12-mm Bolts (2)47 (64)
Front Engine Mount & Bracket
Bracket-To-Engine 10-mm Bolts28 (39)
Bracket-To-Mount 12-mm Through-Bolt (2)47 (64)
Mount-To-Frame 12-mm Bolts69 (94)
Side Engine Mount & Bracket(s)
Side Bracket-To-Engine 8-mm Bolts16 (22)
Side Bracket-To-Engine 10-mm Bolts33 (45)
Engine Mount-To-Side Bracket 12-mm Nuts/Bolts47 (64)
Mount 12-mm Through-Bolt47 (64)
Rear Mount & Bracket Bracket-To-Engine 12-mm Bolts (2)40 (54)
Bracket-To-Mount 12-mm Through-Bolt (2)47 (64)
Engine Mount-To-Frame
10-mm Bolts43 (58)
12-mm Bolts69 (94)
Transmission Mount
Bracket-To-Transmission 10-mm Nuts28 (39)
Mount-To-Bracket 10-mm Nuts/Bolts28 (39)
Mount-To-Engine 12-mm Bolts47 (64)
Mount 12-mm Through-Bolt47 (64)
Engine Oil Pressure Switch13 (18)
Exhaust Manifold Cover Bolts16 (22)
Exhaust Manifold Nuts (2)23 (31)
Exhaust Manifold Support Bracket Bolts33 (45)
Exhaust Manifold-To-Exhaust Pipe Flange Nuts (2)40 (54)
Exhaust Pipe "A" Flange Nuts (2)16 (22)
Exhaust Pipe Bracket Nuts (2)13 (18)
Flywheel Bolts (M/T)76 (103)
Fuel Feed Hose Banjo Nut16 (22)
Generator
Adjustment Brace-To-Bracket 8-mm Bolts16 (22)
Adjustment 8-mm Lock Nut16 (22)
Bracket-To-Engine 10-mm Bolts36 (49)
Mounting 10-mm Pivot Bolt33 (45)
Ignition Coil (Corrosion Resistant)
6-mm Bolt(1)
8-mm Bolt16 (22)
Intake Manifold Chamber Bolts16 (22)
Intake Manifold Nuts16 (22)
Intake Manifold Support Bracket Bolts16 (22)
Knock Sensor23 (32)
M/T Clutch Damper Assembly Bolts16 (22)
M/T Clutch Slave Cylinder 8-mm Bolts16 (22)
M/T Shift/Select Cable Bracket Bolts16 (22)
Oil Cooler Center Bolt54 (74)
Oil Jet Center Mounting Bolt/Check Valve29 (40)
Oil Pan Drain Plug33 (45)
Oil Pan Nuts/Bolts10 (14)
Power Steering Pump
Bracket Adjusting Bolt Brace 6-mm Bolts(1)
Bracket-To-Pump 8-mm Nuts/Bolts16 (22)
Bracket-To-Engine 10-mm Bolts36 (49)
Hose Clamp 6-mm Bolt(1)
Rear Balancer Shaft Gear Bolt18 (25)
Rear Balancer Shaft Maintenance Hole Sealing Plug22 (30)
Rocker Arm Adjuster Lock Nut14 (19)
Timing Belt Adjusting Bolt49 (68)
Timing Belt Adjusting Nut33 (45)
Timing Belt Auto-Tensioner Mounting Bolts16 (22)
Timing Belt Auto-Tensioner Function Maintenance Bolt16 (22)
Transmission-To-Engine Bolts47 (64)
Valve Adjusting Screw Lock Nut14 (19)
VSS/Power Steering Speed Sensor Bolt13 (18)
VTEC Inspection Hole Sealing Bolt14 (20)
INCH Lbs. (N.m)
Baffle Plate Bolts108 (12)
Coolant Bleed Bolt89 (10)
Crankshaft Rear Oil Seal Retainer108 (12)
Generator Terminal Nut72 (8)
Intake Air Duct/Air Cleaner Housing Bolts108 (12)
Oil Jet Rail 6-mm Mounting Bolts108 (12)
Oil Pump Cover Screws61 (7)
Oil Pump Housing Bolts108 (12)
Oil Screen Nuts/Bolts108 (12)
Radiator Upper Bracket Bolts89 (10)
Right & Left Breather Cover Bolts108 (12)
Splash Shield Bolts89 (10)
Throttle Control Cable Bolt (A/T)108 (12)
Timing Belt Auto-Tensioner Oil Maintenance Bolt72 (8)
Valve Cover Cap Nut89 (10)
VTEC Solenoid Bolt106 (12)
Water Pump Bolt106 (12)
(1) Tighten to 108 INCH lbs. (12 N.m). (2) Replace nuts/bolts, DO NOT reuse.
(1)Tighten to 108 INCH lbs. (12 N.m).
(2)Replace nuts/bolts, DO NOT reuse.

TORQUE SPECIFICATIONS

More articles — 2.2L 4-CYL Engine