Home ReviewsRefund
Home/Ford/Transit/Ford Transit VII (2006-2013)/Repair manual/Communication Devices/Module Configuration System: Diagnosis
Contents Wiring diagrams Section: Communication Devices All sections

Module Configuration System: Diagnosis Ford Transit VII

Communication Devices ~408 words

Inspection and Verification

This information provides step-by-step module configuration procedures. Carry out Programmable Module Installation (PMI) when other repair information directs to carry out configuration or when DTCs from the list below are present

DTC Chart

Note. Some modules on this vehicle utilize a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground. Continuous Memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.

DTCDescriptionSourceAction
B2477Module Configuration FailureABS module Audio Control Module (ACM) Generic Electronic Module (GEM) Instrument Cluster (IC) Parking Aid Module (PAM) Restraints Control Module (RCM) Tire Pressure Monitoring System (TPMS) moduleCARRY OUT Programmable Module Installation (PMI). REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
P0602:00Powertrain Control Module Programming Error: No Sub Type InformationPCMCARRY OUT PMI . REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
P0605:00Internal Control Module Read Only Memory ( ROM ) Error: No Sub Type InformationPCMCARRY OUT PMI . REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
P1635:00Tire/Axle Out Of Acceptable Range: No Sub Type InformationPCMCARRY OUT PMI . REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
P1639:00Vehicle ID Block Corrupted, Not Programmed: No Sub Type InformationPCMCARRY OUT PMI . REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
U0300:00Internal Control Module Software Incompatibility: No Sub Type InformationPCMCARRY OUT PMI . REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
U2050No Application PresentABS module ACM IC Occupant Classification System Module (OCSM) RCM TPMS moduleCARRY OUT PMI . REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
U2051One or More Calibration Files Missing/CorruptRCM OCSMCARRY OUT PMI . REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
U2100:00Initial Configuration Not Complete: No Sub Type InformationSpeech Recognition Module (SRM)CARRY OUT PMI . REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
U2101:00Control Module Configuration Incompatible: No Sub Type InformationSRMCARRY OUT PMI . REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
U2202:00Invalid Configuration Data Received: No Sub Type InformationABS module with stability controlCARRY OUT PMI . REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .
U3000:51Control Module: Not ProgrammedSRMCARRY OUT PMI . REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) .

DTC CHART

Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is Available

Note. Following module installation, some modules require a separate learning procedure be carried out. For adaptive learning and calibration instructions, refer to the specific module removal and installation procedures.

  1. Connect the IDS and identify the vehicle as normal.
  2. From the Toolbox icon, select Module Programming and press the check mark.
  3. Select Programmable Module Installation.
  4. Select the module that is being replaced.
  5. Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
  6. Install the new module and press the check mark.
  7. Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
  8. The IDS downloads the data into the new module and displays Module Configuration Complete.
  9. Test module for correct operation.

Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is NOT Available

Note. Following module installation, some modules require a separate learning procedure be carried out. For adaptive learning and calibration instructions, refer to the specific module removal and installation procedures.

  1. Install the new module.
  2. Connect the IDS and identify the vehicle as normal.
  3. From the Toolbox icon, select Module Programming and press the check mark.
  4. Select Programmable Module Installation.
  5. Select the module that was replaced.
  6. Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
  7. Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
  8. If the data is not available, the IDS displays a screen stating to contact the As-Built Data Center. Retrieve the data from the technician service publication website at this time and press the check mark.
  9. Enter the module data and press the check mark.
  10. The IDS downloads the data into the new module and displays Module Configuration Complete.
  11. Test module for correct operation.

More articles — Module Configuration System