Suspension System -- General Information: Specifications — Ford Focus I рестайлинг (2001-2007)

Suspension System -- General Information: Specifications Ford Focus I рестайлинг

FRONT WHEEL ALIGNMENT SPECIFICATIONS - CASTER AND CAMBER

Variant	Values in	Caster-Nominal	Tolerance Range	Camber-Nomina	Tolerance Range
All except wagon	Decimal Degrees	3.03°	4.09° to 1.97°	0.56°	0.70° to -1.82°
All except wagon	Degrees and Minutes	3°02'	4°05' to 1°58'	0°34'	0°42' to -1°49'
Wagon	Decimal Degrees	2.88°	3.89° to 1.87°	0.63°	0.63° to -1.89°
Wagon	Degrees and Minutes	2°53'	3°53' to 1°52'	0°38'	0°38' to -1°53'

FRONT WHEEL ALIGNMENT SPECIFICATIONS - CASTER AND CAMBER

Maximum variance - left-hand to right-hand side - Caster 1.00° (1°00') Camber 1.25° (1°15')

Tolerance Range	Setting Adjustment, if required
(0 Toe) +/- 0.20°	(0 Toe) +/- 0.20°

FRONT WHEEL ALIGNMENT SPECIFICATIONS - TOTAL TOE SETTING - ALL VARIANTS (EXCEPT 2.0L DURATEC ST)

Tolerance Range	Setting Adjustment, if required
0.15° (Toe-out) +/- 0.25°	0.15° (Toe-out) +/- 0.15°
0° 09' (Toe-out) +/- 0° 15'	0° 09' (Toe-out) +/- 0° 09'
1.1 mm (Toe-out) °1.9 mm	1.1 mm (Toe-out) +/-1.1 mm

FRONT WHEEL ALIGNMENT SPECIFICATIONS - TOTAL TOE SETTING - 2.0L DURATEC ST

Variant	Values in	Camber-Nominal	Tolerance Range
All except wagon	Decimal Degrees	1.02°	0.29° to -2.33°
All except wagon	Degrees and Minutes	L°01'	0°17' to -2°20'
Wagon	Decimal Degrees	0.94°	0.34° to -2.22°
Wagon	Degrees and Minutes	0°56'	0°20' to -2°13'

REAR WHEEL ALIGNMENT SPECIFICATIONS - CAMBER

Maximum variance - left-hand to right-hand side - Camber 1.25° (1°15')

Tolerance Range	Setting Adjustment, if required
0.50° (Toe-in) +/- 0.20°	0.50° (Toe-in) +/- 0.20°

REAR WHEEL ALIGNMENT SPECIFICATIONS - TOTAL TOE SETTING - ALL VARIANTS (EXCEPT 2.0L DURATEC ST)

Tolerance Range	Setting Adjustment, if required
0.55° (Toe-in) to 0.05° (Toe-in)	0.30° (Toe-in) +/- 0.15°
0° 33' (Toe-in) to 0° 03' (Toe-in)	0° 18' (Toe-in) +/- 0° 09'
4.2 mm (Toe-in) to 0.4 mm (Toe-in)	2.3 mm (Toe-in) +/-1.1 mm

REAR WHEEL ALIGNMENT SPECIFICATIONS - TOTAL TOE SETTING - 2.0L DURATEC ST

Item	Specification
Ball Joint Deflection
Lower ball joint	0-0.2 mm (0-0.008 in)

GENERAL SPECIFICATIONS

Description	Nm
Tie-rod end locknut	63
Rear lower arm to crossmember cam bolt nut	115

TORQUE SPECIFICATIONS