Module Configuration System: Diagnosis Ford Fiesta Mk6

Inspection and Verification

This information provides step-by-step module configuration procedures. Carry out the Programmable Module Installation (PMI) procedures in this information when directed here from other workshop information to carry out configuration or when DTCs from the list below are present

DTC Chart

Note. modules on this vehicle utilize a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground. Continuous Memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.

DTC CHART

Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is Available

Note. Following module installation, some modules require a separate procedure be carried out. For instructions, refer to the appropriate module removal and installation procedures.

1. Connect the IDS and identify the vehicle as normal.
2. From the Toolbox icon, select Module Programming and press the check mark.
3. Select Programmable Module Installation.
4. Select the module that is being replaced.
5. Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
6. Install the new module and press the check mark.
7. Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
8. The IDS downloads the data into the new module and displays Module Configuration Complete.
9. Test module for correct operation.

Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is NOT Available

Note. Following module installation, some modules require a separate procedure be carried out. For instructions, refer to the appropriate module removal and installation procedures.

1. Install the new module.
2. Connect the IDS and identify the vehicle as normal.
3. From the Toolbox icon, select Module Programming and press the check mark.
4. Select Programmable Module Installation.
5. Select the module that was replaced.
6. Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
7. Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
8. If the data is not available, the IDS displays a screen stating to contact the As-Built Data Center. Retrieve the data from the technician service publication website at this time and press the check mark.
9. Enter the module data and press the check mark.
10. The IDS downloads the data into the new module and displays Module Configuration Complete.
11. Test module for correct operation.

Accessory Protocol Interface Module (APIM) Programming Using the Integrated Diagnostic System (IDS)

Note. If a new Accessory Protocol Interface Module (APIM) is being installed, install the new APIM before carrying out the following procedure. For additional information, refer to INFORMATION AND ENTERTAINMENT SYSTEMS .

1. Turn the Audio Control Module (ACM) on.
2. Connect the scan tool to the Data Link Connector (DLC).
3. Connect one end of the Universal Serial Bus (USB) male-A to male-A cable to the scan tool.
4. Connect the other end of the USB male-A to male-A cable to the vehicle USB port.
5. From the technician service publication website, run On-Line Automotive Service Information System (OASIS) using Quick Start or by manually entering the Vehicle Identification Number (VIN).
6. From the OASIS tab, select the "Sync/ APIM " bullet.
7. Select the "Read APIM " button to verify the current APIM Vehicle Interface Processor (VIP) and Consumer Interface Processor (CIP) software levels.
8. NOTE: Do not disconnect the Vehicle Communication Module (VCM) or USB cables during APIM programming. Select the desired software level from the list of available software for programming then select the "Program APIM " button to begin the APIM programming process. Enter the APIM As-Built data if prompted. When the VIP is programmed, the CIP will be programmed automatically.
9. The Sync/ APIM application downloads the software into the APIM and displays "Programming has been completed successfully".
10. After the SYNC system programming has completed, press the phone button once and wait for 1 minute for the SYNC system to reboot.
11. Test the audio system for correct operation.