Crankcase Capacity
Oil capacity is 4.5 qts. (4.25L) with filter.
| Application | (1) Qts. (L) |
|---|
| 2.0L | 4.5 (4.25) |
| (1) Includes oil filter. |
CRANKCASE CAPACITY SPECIFICATIONS
TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) |
|---|
| Camshaft Bearing Caps | (1) |
| Camshaft Sprocket Bolt | 75 (101) |
| Connecting Rod Bolts | (2) 20 (27) |
| Crankshaft Main Bearing Cap/Bedplate (3) |
| M8 Bedplate Bolts | 21 (28) |
| M11 Main Cap Bolts | 55 (75) |
| Crankshaft Damper Pulley Bolt | 105 (142) |
| Cylinder Head Bolts | (4) |
| Engine Support Bracket Attaching Bolts | 71 (97) |
| Engine Support Bracket Through Bolt | 71-85 (97-118) |
| Exhaust Manifold-To-Cylinder Head Bolts | 17 (23) |
| Flexplate-To-Crankshaft Flange | (5) |
| Flywheel-To-Crankshaft Flange | (5) |
| Intake Manifold Nuts (6) | 17 (23) |
| Oil Filter Adapter | 40 (55) |
| Oil Filter | 15 (20) |
| Oil Pump Relief Valve Retaining Cap | 39 (54) |
| Power Steering Pump-to-Bracket Bolts | 29 (39) |
| Power Steering Pump Bracket-to-Engine Bolts | 29 (39) |
| Timing Belt Tensioner Bolts | 23 (31) |
| Transaxle Mount Through Bolt | 50 (69) |
| Transaxle Mount Vertical Bolt | 41 (56) |
| INCH Lbs. (N.m) |
| Oil Pan Bolts | 106 (12) |
| Oil Pump Cover Bolt | 106 (12) |
| Valve Cover Bolts | (7) |
| Water Pump-To-Engine Block | 106 (12) |
| (1) Tighten bolts to specification. See the installation procedure in CAMSHAFT & CAM FOLLOWER . (2) Tighten bolts to specification, then tighten an additional 1/4 turn. (3) Tighten bolts to specification. See CRANKSHAFT & MAIN BEARINGS in CYLINDER BLOCK ASSEMBLY under OVERHAUL. (4) See Cylinder Head INSTALLATION procedure. (5) Torque specification, not available from manufacturer. (6) Start at center and move outwards. (7) Tighten bolts in 3 steps. See the installation procedure in CAMSHAFT & CAM FOLLOWER . |
| (1) | Tighten bolts to specification. See the installation procedure in CAMSHAFT & CAM FOLLOWER . |
| (2) | Tighten bolts to specification, then tighten an additional 1/4 turn. |
| (3) | Tighten bolts to specification. See CRANKSHAFT & MAIN BEARINGS in CYLINDER BLOCK ASSEMBLY under OVERHAUL. |
| (4) | See Cylinder Head INSTALLATION procedure. |
| (5) | Torque specification, not available from manufacturer. |
| (6) | Start at center and move outwards. |
| (7) | Tighten bolts in 3 steps. See the installation procedure in CAMSHAFT & CAM FOLLOWER . |
GENERAL ENGINE SPECIFICATIONS
| Application | Specification |
|---|
| Displacement | 122 Cu. In. (2.0L) |
| Bore | 3.445" (87.5 mm) |
| Stroke | 3.267" (83 mm) |
| Compression Ratio | 9.6:1 |
| Fuel System | SFI |
| Horsepower @ RPM | (1) |
| Torque Ft. Lbs. @ RPM | (1) |
| (1) Specification not available. |
| (1) | Specification not available. |
GENERAL ENGINE SPECIFICATIONS
