Circuit/System Description
The Driver Door Switch (DDS) or Passenger Door Switch (PDS) controls the mirror horizontal and vertical motors through the use of bi-directional motor controls. When the mirror is commanded up, voltage is supplied to the mirror vertical motor through the Driver/Passenger Mirror Motor Right/Down Motors Common circuit and ground is supplied through the Driver/Passenger Mirror Motor Down Control circuit. When the mirror is commanded down, voltage is supplied to the mirror vertical motor through the Driver/Passenger Mirror Motor Down Control circuit and ground is supplied through the Driver/Passenger Mirror Motor Right/Down Motors Common circuit.
Horizontal controls operate in the same manner with the Driver/Passenger Mirror Motor Right/Down Motors Common circuit supplying voltage and the Driver/Passenger Mirror Motor Right Control circuit supply a ground to the mirror horizontal motor when the mirror is commanded right. When the mirror is commanded left, voltage is supplied to the mirror horizontal motor through the Driver/Passenger Mirror Motor Right Control circuit and ground is supplied through the Driver/Passenger Mirror Motor Right/Down Motors Common circuit.
The Driver Door Switch (DDS) and Passenger Door Switch (PDS) determine the position of the outside rearview mirrors based on inputs from two mirror position sensors, one for vertical position, the other for horizontal position. Five volts is applied to each sensor through a shared 5-volt reference circuit and a shared low reference circuit supplies ground. Each sensor has an individual signal circuit which provides position voltage to the DDS/PDS.
The Driver Door Switch (DDS) and Passenger Door Switch (PDS) supply voltage to the outside rearview mirror heater elements upon receipt of a serial data message from the HVAC module indicating that the rear defrost system is active. The door switch supplies B+ through the driver/passenger mirror heating element supply voltage circuit when a request is seen. Ground is applied through the driver/passenger mirror heating low reference circuit.
The Driver Door Switch (DDS) and Passenger Door Switch (PDS) control the power folding or power extending functions of the outside rearview mirrors. The folding mirror motors are controlled by using bi-directional motor controls through the folding mirror motor retract control circuit and the folding mirror motor extend control circuit.
The Driver Door Switch (DDS) and Passenger Door Switch (PDS) supply voltage to the outside rearview mirror heater elements upon receipt of a serial data message from the HVAC module indicating that the rear defrost system is active. The door switch supplies B+ through the driver/passenger mirror heating element supply voltage circuit when a request is seen. Ground is applied through the driver/passenger mirror heating low reference circuit.
The R/DEFOG relay supplies voltage to the outside rearview mirror heater elements based on the current state of the rear window defogger. The replay supplies B+ through the driver/passenger mirror heating element supply voltage circuit when a request is seen.
The inside rearview mirror uses 2 photocell sensors. One sensor is the rear light sensor, located on the face side of the mirror, facing the rear of the vehicle. The rear light sensor is used to determine light conditions present at the mirror face. The other sensor is the front light sensor, located on the backside of the mirror, facing the front of the vehicle. The front light sensor is used to determine the exterior light conditions at the front of the vehicle. With a low exterior light condition detected by the front light sensor and a high light condition from the rear light sensor, the inside rearview mirror will automatically darken the face of the inside rearview mirror and the left outside rearview mirror. The inside rearview mirror provides a signal circuit and a low reference circuit to the left mirror face to darken the mirror when needed.
With the gear selector lever in the REVERSE position, backup lamp supply voltage is supplied as an input to the inside rearview mirror. The mirror monitors this input to disable the automatic day-night feature. This allows the driver to see objects in the mirror clearly when backing up, regardless of the rear light sensor status.
The inside rearview mirror uses 2 photocell sensors. One sensor is the rear light sensor, located on the face side of the mirror, facing the rear of the vehicle. The rear light sensor is used to determine light conditions present at the mirror face. The other sensor is the front light sensor, located on the backside of the mirror, facing the front of the vehicle. The front light sensor is used to determine the exterior light conditions at the front of the vehicle. With a low exterior light condition detected by the front light sensor and a high light condition from the rear light sensor, the inside rearview mirror will automatically darken the face of the inside rearview mirror.
With the gear selector lever in the REVERSE position, backup lamp supply voltage is supplied as an input to the inside rearview mirror. The mirror monitors this input to disable the automatic day-night feature. This allows the driver to see objects in the mirror clearly when backing up, regardless of the rear light sensor status.
The Driver Door Switch (DDS) and Passenger Door Switch (PDS) control the power folding or power extending functions of the outside rearview mirrors. The folding mirror motors are controlled by using bi-directional motor controls through the folding mirror motor retract control circuit and the folding mirror motor extend control circuit.
The Driver Door Switch (DDS) or Passenger Door Switch (PDS) controls the mirror horizontal and vertical motors through the use of bi-directional motor controls. When the mirror is commanded up, voltage is supplied to the mirror vertical motor through the Driver/Passenger Mirror Motor Right/Down Motors Common circuit and ground is supplied through the Driver/Passenger Mirror Motor Down Control circuit. When the mirror is commanded down, voltage is supplied to the mirror vertical motor through the Driver/Passenger Mirror Motor Down Control circuit and ground is supplied through the Driver/Passenger Mirror Motor Right/Down Motors Common circuit.
Horizontal controls operate in the same manner with the Driver/Passenger Mirror Motor Right/Down Motors Common circuit supplying voltage and the Driver/Passenger Mirror Motor Right Control circuit supply a ground to the mirror horizontal motor when the mirror is commanded right. When the mirror is commanded left, voltage is supplied to the mirror horizontal motor through the Driver/Passenger Mirror Motor Right Control circuit and ground is supplied through the Driver/Passenger Mirror Motor Right/Down Motors Common circuit.
On vehicles equipped with RPO DL3/DR4, the Driver Door Switch (DDS) and Passenger Door Switch (PDS) determines the position of the outside rearview mirrors based on inputs from two mirror position sensors, one for vertical position, the other for horizontal position. 5 volts is applied to each sensor through a shared 5-volt reference circuit and a shared low reference circuit supplies ground. Each sensor has an individual signal circuit which provides position voltage to the DDS/PDS.
The outside rearview mirror switch controls the outside rearview mirrors based on the position of the mirror selector switch and which movement position is selected. The outside rearview mirror switch has four positions: up, down, left, and right. B+ is applied to the switch and when a movement position switch is selected, B+ is sent to the commanded mirror via a mirror control control. The opposite mirror control circuit acts as a ground circuit for the bi-directional mirror motor. Ground is the applied through the switch.
Heated Outside Rearview Mirror Operation
The REAR DEFOG relay controls the operation of the heated outside rearview mirrors. When rear window defogging is requested, the REAR DEFOG relay is energized and B+ is applied to the supply voltage circuit of the mirror heater element, located in the mirror face. A constant ground is also applied to the mirror face. Current will pass through the mirror heater element, warming the mirror, so long as the rear window defogger is commanded ON.
Inside Rearview Mirror with the Automatic Day-Night Feature System Operation
The inside rearview mirror uses 2 photocell sensors. One sensor is the headlight sensor, located on the face side of the mirror. The headlight sensor is used to determine light conditions present at the mirror face. The other sensor is the ambient light sensor, located on the rear of the mirror or windshield side. The ambient light sensor is used to determine the exterior light conditions. With a low exterior light condition detected, and a high light condition from behind of the car, at the headlight sensor, the inside rearview mirror will automatically darken the face of the mirror.
In the daytime, the mirror is in a normal state because of the high exterior light condition that is indicated by the ambient light sensor. With the gear selector lever in the REVERSE position, backup lamp supply voltage is supplied as an input to the inside rearview mirror. The mirror monitors this input to disable the automatic day-night feature. This allows the driver to see objects in the mirror clearly when backing up, even during the night.