Home/Volvo/V70/Volvo V70 II (2000-2004)/Repair manual/Gearbox, Input/output Speed Sensor - Removal & Installation
Manual sections Wiring diagrams
Repair manual

Gearbox, Input/output Speed Sensor - Removal & Installation Volvo V70 II

Step-by-step instructions on "Gearbox, Input/output Speed Sensor - Removal & Installation" for Volvo V70 II (2000–2004). Pick an article — removal, installation, adjustment and diagnostics with illustrations.

62subsections
62articles
112illustrations

Gearbox, removing (Preparatory work)

1 article

Disconnecting the battery lead

1 article

Gearbox, removing (AW50/51 AWD; AW55-50/51SN; 2003-2007)

1 article

Gearbox, removing (M56; 2001-2007)

1 article

Gearbox, removing

1 article

Removing the hose

1 article

Measuring the position of the tie rod in the steering gear

1 article

Exposing the steering shaft joint

1 article

Removing the cap for the drive shaft support bearing

1 article

Installing the gearbox (AW50/51 AWD; B5234T3, AW55-50/51SN; 2001-2004)

1 article

Installing the angle gear

1 article

Installing the collision protection system over the steering gear

1 article

Installing the water hose

1 article

Installing the battery cable

1 article

Check

1 article

Installing the gearbox (AW50/51 AWD; AW55-50/51SN; 2001)

1 article

Installing the gearbox

1 article

Lifting the engine/gearbox

1 article

Installing the rear engine mounting

1 article

Installing the lower oil pipe to the gearbox

1 article

Installing the left-hand drive shaft to the gearbox and the wheel spindle

1 article

Fitting the subframe to the body

1 article

Installing the steering wheel shaft joint

1 article

Installing the crossmembers

1 article

Installing the cable conduit

1 article

Removing the lifting beam

1 article

Fitting the remaining screws to the gearbox/starter motor

1 article

Installing the gear selector cables and oil line

1 article

Installing service clips

1 article

Installing engine compartment components

1 article

Installing the collision protection system over the steering gear (right-hand drive cars)

1 article

Lifting the engine and gearbox to the horizontal position

1 article

Installing the subframe on the bodywork

1 article

Installing the sealing ring for the CV joint housing

1 article

Installing the left drive shaft on the gearbox, stub axle and control arm

1 article

Installing the screws for the front engine pad

1 article

Installing the right drive shaft on the gearbox, stub axle and control arm

1 article

Installing new lock nuts on the steering gear

1 article

Lowering the car and removing the lifting beam and lifting tools from the engine

1 article

Installing the coolant hose

1 article

Installing the gearbox (TCM-002E, AW55-50/51SN; AW50/51 AWD; AW55-50/51SN; 2001-2007)

1 article

Fitting the sub-frame to the body

1 article

Installing the service clips

1 article

Installing the gearbox (B5254T4, TF-80SC AWD; 2006-2007)

1 article

Installing the left drive shaft on the transmission and the wheel spindle

1 article

Software

1 article

Jacking points, body

1 article

Installing the charge air pipe (only applies to 6-cylinder turbocharged engines)

1 article

Gear-shift position sensor, checking/adjusting

1 article

Gear-shift position sensor, checking/adjusting (AW50/51 AWD; AW55-50/51SN; 2001-2007)

1 article

Installing the gear selector cable

1 article

Input speed sensor/output speed sensor, replacing

1 article

Preparations

1 article

Installing the sensor

1 article

Installing the air cleaner (ACL) housing

1 article

Input speed sensor/output speed sensor, replacing (AW50/51 AWD; AW55-50/51SN; 2003-2007)

1 article

Information about the CAN network, structure and function

1 article

Joining cables

1 article

Disconnect the battery

1 article

Treat the cable terminal surfaces

1 article

Installing wheels (B5234T3; B5244S; B5244T3; 2001-2007)

1 article