Maintenance Reminder Light Reset Procedures: Other Volkswagen Jetta V

OXYGEN SENSOR WARNING LIGHT

Note. To determine the appropriate reset procedure, refer to OXYGEN SENSOR WARNING LIGHT RESET INDEX . Only vehicles listed in this index have an Oxygen Sensor Warning Light reset.

OXYGEN SENSOR WARNING LIGHT RESET INDEX

SERVICE REMINDER INDICATOR (SRI)

Note. Some Service Reminder Indicators (SRI) were eliminated from late production 1999 and later vehicles. Use VIN to identify early and late production vehicles. For Golf and GTI, the 7th and 8th characters of the VIN are 1J for the late 1999 production vehicles. For Jetta, 7th and 8th characters of the VIN are 9M for the late 1999 production vehicles. On early production vehicles, the 7th and 8th characters of the VIN are 1H.

Note. To determine the appropriate reset procedure, refer to SRI RESET INDEX . Only vehicles listed in this index have an SRI reset.

SRI RESET INDEX

Using Buttons in Instrument Cluster (Basic Message Display)

1. Ensure the ignition is switched off. NOTE: If resetting the Inspection Service Reminder, turn on emergency flashers. If resetting the Oil Change Reminder, go to next step.
2. Press and hold the 0.0 (trip reset) button (3). (Scheme 4), (Scheme 5), or (Scheme 6).
3. Switch ignition on. Release the 0.0 button. Press the HOUR and MINUTE button (clock reset button (1) one time, quickly.
4. The Service Interval Display is now in the Reset mode.
5. After a brief period, the display switches back to the normal display.
6. Turn off ignition and remove key from lock. Wait at least 10 seconds.
7. Insert key and start engine. The service interval is now reset. Confirm "wrench" indicator light is not illuminated.

Scheme 2

Scheme 3

Scheme 4

Using The Windshield Wiper Lever Buttons (Premium Message Display)

1. Using the rocker switch on the windshield wiper lever (2), select the "Settings" menu. (Scheme 7)
2. Once in the service submenu, select "Reset", then press the "OK" button (1). The service interval is now reset.

Scheme 5

Using The Buttons In Multifunction Steering Wheel

1. Press the appropriate multifunction steering wheel button continually until the "Settings" menu is displayed (button 1 in 2004-08 Golf Sedan & 2004 R32, or button 5 in all other models). see scheme 8or see scheme 9 )
2. Once in the service submenu, select "Reset" and then press the "OK" button (3 in 2004-08 Golf Sedan & 2004 R32, or 5 in all other models). The service interval is now reset.

Scheme 6

Scheme 7

TIRE PRESSURE MONITOR SYSTEM (TPMS)

Note. To determine the appropriate reset procedure, refer to TPMS RESET INDEX . Only vehicles listed in this index have a TPMS reset.

TPMS RESET INDEX

Tire Pressure Monitor Warning Light

When the low tire pressure warning light comes on, immediately check air pressure of all tires and adjust to the specified pressure. Reset TPM system. See Tire Pressure Monitor System Reset . If light is still on, there is a malfunction in the TPM system. See appropriate manufacturer service information.

Under the following conditions, the system may not function properly

1. Insufficient tire pressure.
2. Structural damage on tires.
3. Load on vehicle on one side.
4. One axle is heavily loaded (i.e., when pulling a trailer).
5. When snow chains are used.
6. When spare wheel is installed.
7. One wheel is replaced.
8. Tire pressure sensor battery is depleted (7-10 year life span).

Basic Setting

1. Set the tire pressure of all wheels to specified pressure.
2. With vehicle stopped and parking brake applied, turn ignition switch to ON position.
3. Press SET button (located near gear shift) until an audio signal is heard. see scheme 10 The signal confirms basic setting.

After Wheel Or Pressure Change

1. Set the tire pressure of all wheels to specified pressure.
2. With parking brake applied, allow vehicle to stand for 20 minutes (5 minutes after a recognized tire puncture) so that control module enters learning mode.
3. Drive vehicle at 16 mph (25 km/h) or more. As soon as vehicle reaches this speed, tire pressure sensor IDs are automatically recognized and read by control module. NOTE: An acceleration data check also occurs with vehicle speed. This process takes about 7 minutes.

When the low tire pressure warning light comes on, immediately check air pressure of all tires and adjust to the specified pressure. If light is still on, there is a malfunction in the TPM system. See appropriate manufacturer service information.

Under the following conditions, the system may not function properly

1. Insufficient tire pressure.
2. Structural damage on tires.
3. Load on vehicle on one side.
4. One axle is heavily loaded (i.e., when pulling a trailer).
5. When snow chains are used.
6. When a spare wheel without a pressure sensor is installed.
7. One wheel is replaced.
8. Tire pressure sensor battery is depleted (7-10 year life span).