Lan Communication System - Lan (Diagnostics): Overview Subaru Forester SH рестайлинг

OPERATION

1. On the << Main Menu >> display screen, select {Each System Check}.
2. On the << Each System Check >> menu display screen, select the {Integ. unit mode}.
3. Select the [OK] after the information of body integrated unit type is displayed.
4. On the << Integ. unit mode >> display screen, select the {Diagnostic Code(s) Display}.
5. Record the DTC displayed. NOTE: For details concerning the operation procedure, refer to the PC application help for Subaru Select Monitor. For details concerning DTC, refer to "List of Diagnostic Trouble Code (DTC)". < Ref. to «LIST OF DIAGNOSTIC TROUBLE CODE (DTC)»(ref-465425-S36850022452012042000000) . >

1. On << Main Menu >> display, select {Each System Check}.
2. On << System Selection Menu >> display, select {Integ. unit mode}.
3. Press the [OK] key after the information of body integrated unit type is displayed.
4. On << Integ. unit mode failure diag >> display, select {Clearing Memory} and press the [OK] key. MEMORY CLEARING DISPLAY REFERENCE CHART Display Contents to be displayed Clear Memory? Clear function of DTC and freeze frame data
5. When "Done" is shown on the display screen, turn the ignition switch to OFF. NOTE: For detailed operation procedures, refer to PC application help for Subaru Select Monitor.

1. On the << Main Menu >> display screen, select {Each System Check}.
2. On the << System Selection Menu >> display screen, select the {Integ. unit mode}.
3. On the << Integ. unit mode failure diag >> display screen, select the {Current Data Display & Save}.
4. Using the scroll key, scroll the display screen up or down until the desired data is shown.

1. On << Main Menu >> display, select {Each System Check}.
2. On << System Selection Menu >> display, select {Integ. unit mode}.
3. On << Integ. unit mode failure diag. >> display, select {Integ. Unit customizing}.
4. Change the setting with UP/DOWN key and set with the [OK] key. List of User Customizing item USER CUSTOMIZING ITEM REFERENCE CHART Data Initial setting value Customize setting Remarks Off delay time Long Delay time below can be selected by setting. OFF 0 second Short 10 seconds Normal 20 seconds Long 30 seconds Rr Defogger op. mode 15 minutes 15 minutes Automatically stops in 15 minutes after switch is turned to ON. Continuous Repeats active condition for 15 minutes and inactive condition for 2 minutes until switch is turned to OFF. Security Alarm Setup ON ON Security alarm (hazard, horn or siren) in active condition OFF Security alarm in inactive condition Impact Sensor Setup OFF ON Workable when Impact Sensor Setup is set to "ON". Impact sensor function becomes activated. OFF Impact sensor in inactive condition (Set to "OFF" in models without sensors.) Alarm delay setup ON After the keyless lock operation, the alarm monitor starts after the following delay time has passed. ON Delay time is 30 seconds. OFF Delay time is 0 seconds. Lockout prevention ON ON Lockout prevention in active condition. (The function does not operate if safety knob is locked by hand.) OFF Lockout prevention in inactive condition Impact sensor (OP) OFF ON Vehicle is controlled in impact sensor equipped mode. (Make sure to set to "OFF" for models without the impact sensor. When "ON", hazard, horn or siren become activated by keyless lock (alarm monitor start). OFF Vehicle is controlled in no impact sensor mode. Buzzer beeping setup ON ON When lock/unlock is selected by keyless entry system operation, buzzer operates. OFF When lock/unlock is selected by keyless entry system operation, buzzer does not operate. Emergency light setup ON ON When lock/unlock is selected by keyless entry system operation, buzzer operates. OFF When lock/unlock is selected by keyless entry system operation, buzzer does not operate. Buzzer setting ON ON Vehicle is controlled in answer-back buzzer equipped mode. OFF Vehicle is controlled in answer-back buzzer non-equipped mode. (Make sure to set to "OFF" in models without answer back buzzers.) Initial keyless setting - - - Execution Settings of keyless entry system are initialized. Initial button setting - - - Execution Settings of each function are initialized. Passive Alarm OFF ON Setting only for North American models OFF Door open warning ON ON If detecting door open for 20 minutes, room light, map light, and key ring illumination that are related to doors are turned off to prevent battery runout. OFF Room light, map light, key illumination and door warning light are not turned off. Dome Light Alarm Setting OFF ON The room light lights by being interlocked with the activation of the alarm. OFF Map Light Setting ON ON Illuminates in accordance with the door interlocked room light. OFF Belt Warning Switch ON ON When using normally OFF Stop the belt warning buzzer beep and warning light illumination.
5. After setting, make sure that the setting changed {Current Data Display & Save} is same as vehicle equipment. CAUTION: The above settings must match the actual vehicle equipment. Do not change settings except for setting above while setting the functions. Be sure not to change Factory initial setting except when installing a new body integrated unit. NOTE: For detailed operation procedures, refer to PC application help for Subaru Select Monitor.

Note. In order to check the body integrated unit function, inspect the body integrated unit and actuator using Subaru Select Monitor without operating switches.

1. On << Main Menu >> display, select {Each System Check}.
2. On << System Selection Menu >> display, select {Integ. unit mode}.
3. On << Integ. unit mode failure diag. >> display, select {Function check}.
4. Select the item to be operated on the << Function check >> display screen with "UP/Down key" and press the [Next] button.
5. Pressing [Next] starts, [End] cancels the operation and [OK] returns to the System Operation Check Mode display screen. NOTE: If not equipped (based on area or condition), process will not go on. For detailed operation procedures, refer to PC application help for Subaru Select Monitor.