Home ReviewsRefund
Home/Scion/FR-S/Scion FR-S I (2012-2016)/Repair manual/Windows/Power Window Control System (Diagnostic Codes & Symptom Tes…
Contents Wiring diagrams Section: Windows All sections

Power Window Control System (Diagnostic Codes & Symptom Tests): Other Scion FR-S I

Windows ~6008 words

PROCEDURE

  1. CHECK DTC OUTPUT Clear the DTC. Refer to «DTC CHECK / CLEAR [07/2013 - ]»(ref-612250-S01413683982014042900000) . Check for DTCs. Refer to «DTC CHECK / CLEAR [07/2013 - ]»(ref-612250-S01413683982014042900000) . RESULT Result Proceed to DTC B2311 is output A DTC B2314 is output B B --> See step 6 A: Go to next step
  2. READ VALUE USING TECHSTREAM Connect the Techstream to the DLC3. Turn the ignition switch to ON. Turn the Techstream on. Enter the following menus: Body Electrical / Master Switch / Data List. According to the display on the Techstream read the Data List. MASTER SWITCH Tester Display Measurement Item/Range Normal Condition Diagnostic Note Current D Sensor Fail Mode1 Driver side sensor fail mode1(power of sensor malfunction) /Detected or Not Detected Not Detected - Current D Sensor Fail Mode2 Driver side sensor fail mode2(Pulse sensor1 malfunction) /Detected or Not Detected Not Detected - Current D Sensor Fail Mode3 Driver side sensor fail mode3(Pulse sensor2 malfunction) /Detected or Not Detected Not Detected - Current D Sensor Fail Mode4 Driver side sensor fail mode4(Pulse direction error) /Detected or Not Detected Not Detected - Current D Sensor Fail Mode5 Driver side sensor fail mode5(Pulse stop) /Detected or Not Detected Not Detected - Current D Sensor Fail Mode6 Driver side sensor fail mode6(Dead zone opening direction error) /Detected or Not Detected Not Detected - OK On the Techstream screen, Not Detected is displayed. RESULT Result Proceed to Detect A Not Detect B B --> See step 11 A: Go to next step
  3. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY) Disconnect the E8 power window regulator master switch assembly connector. Disconnect the E5 power window regulator motor assembly connector. Measure the resistance according to the value(s) in the table below. Standard Resistance (Check for Open) CURRENT D SENSOR FAIL MODE 1 Tester connection Condition Specified condition E8-3 (VCC) - E5-5 (VCC) Always Below 1 ohms E8-14 (SGD) - E5-4 (SGD) Always Below 1 ohms CURRENT D SENSOR FAIL MODE 2 Tester connection Condition Specified condition E8-8 (SN1) - E5-6 (SN1) Always Below 1 ohms CURRENT D SENSOR FAIL MODE 3 Tester connection Condition Specified condition E8-1 (SN2) - E5-2 (SN2) Always Below 1 ohms CURRENT D SENSOR FAIL MODE 4 Tester connection Condition Specified condition E8-1 (SN2) - E5-2 (SN2) Always Below 1 ohms E8-8 (SN1) - E5-6 (SN1) Always Below 1 ohms CURRENT D SENSOR FAIL MODE 5 Tester connection Condition Specified condition E8-1 (SN2) - E5-2 (SN2) Always Below 1 ohms E8-3 (VCC) - E5-5 (VCC) Always Below 1 ohms E8-8 (SN1) - E5-6 (SN1) Always Below 1 ohms E8-14 (SGD) - E5-4 (SGD) Always Below 1 ohms CURRENT D SENSOR FAIL MODE 6 Tester connection Condition Specified condition E8-1 (SN2) - E5-2 (SN2) Always Below 1 ohms E8-3 (VCC) - E5-5 (VCC) Always Below 1 ohms E8-8 (SN1) - E5-6 (SN1) Always Below 1 ohms E8-14 (SGD) - E5-4 (SGD) Always Below 1 ohms Standard Resistance (Check for Short) CURRENT D SENSOR FAIL MODE 1 Tester connection Condition Specified condition E8-3 (VCC) Body ground Always 10 kohms or higher E8-14 (SGD) Body ground Always 10 kohms or higher CURRENT D SENSOR FAIL MODE 2 Tester connection Condition Specified condition E8-8 (SN1) -Body ground Always 10 kohms or higher CURRENT D SENSOR FAIL MODE 3 Tester connection Condition Specified condition E8-1 (SN2) - Body ground Always 10 kohms or higher CURRENT D SENSOR FAIL MODE 4 Tester connection Condition Specified condition E8-1 (SN2)- Body ground Always 10 kohms or higher E8-8 (SN1) - Body ground Always 10 kohms or higher CURRENT D SENSOR FAIL MODE 5 Tester connection Condition Specified condition E8-1 (SN2)- Body ground Always 10 kohms or higher E8-3 (VCC) - Body ground Always 10 kohms or higher E8-8 (SN1) - Body ground Always 10 kohms or higher E8-14 (SGD) - Body ground Always 10 kohms or higher CURRENT D SENSOR FAIL MODE 6 Tester connection Condition Specified condition E8-3 (VCC) - Body ground Always 10 kohms or higher E8-8 (SN1) - Body ground Always 10 kohms or higher E8-14 (SGD) - Body ground Always 10 kohms or higher E8-14 (SGD) - Body ground Always 10 kohms or higher NG --> REPAIR OR REPLACE HARNESS OR CONNECTOR OK: Go to next step
  4. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY Remove the power window regulator motor assembly. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S19549818492014042900000) . Inspect the power window regulator motor assembly. Refer to «INSPECTION [07/2013 - ]»(ref-612430-S39510651692014042900000) . NG --> See step 12 OK: Go to next step
  5. REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Temporarily replace the power window regulator master switch assembly with a new or normally functioning one. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S08305805372014042900000) . Check the power window regulator master switch assembly operates. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Driver door power window operates normally. RESULT Result Proceed to Does not operate A Operate B B --> END A --> REPLACE POWER WINDOW REGULATOR ASSEMBLY
  6. READ VALUE USING TECHSTREAM Connect the Techstream to the DLC3. Turn the ignition switch to ON. Turn the Techstream on. Enter the following menus: Body Electrical / Master Switch / Data List. According to the display on the Techstream read the Data List. MASTER SWITCH Tester Display Measurement Item/Range Normal Condition Diagnostic Note Current P Sensor Fail Mode1 Front passenger side sensor fail mode1(power of sensor malfunction) /Detected or Not Detected Not Detected - Current P Sensor Fail Mode2 Front passenger side sensor fail mode2(Pulse sensor1 malfunction) /Detected or Not Detected Not Detected - Current P Sensor Fail Mode3 Front passenger side sensor fail mode3(Pulse sensor2 malfunction) /Detected or Not Detected Not Detected - Current P Sensor Fail Mode4 Front passenger side sensor fail mode4(Pulse direction error) /Detected or Not Detected Not Detected - Current P Sensor Fail Mode5 Front passenger side sensor fail mode5(Pulse stop) /Detected or Not Detected Not Detected - Current P Sensor Fail Mode6 Front passenger side sensor fail mode6(Dead zone opening direction error) /Detected or Not Detected Not Detected - OK On the Techstream screen, Not Detected is displayed. RESULT Result Proceed to Detect A Not Detect B B --> See step 11 A: Go to next step
  7. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY) Disconnect the F6 power window regulator master switch assembly connector. Disconnect the F1 power window regulator motor assembly connector. Measure the resistance according to the value(s) in the table below. Standard Resistance (Check for Open) CURRENT P SENSOR FAIL MODE 1 Tester connection Condition Specified condition F6-3 (VCC) - F1-5 (VCC) Always Below 1 ohms F6-14 (SGD) - F1-4 (SGD) Always Below 1 ohms CURRENT P SENSOR FAIL MODE 2 Tester connection Condition Specified condition F6-8 (SN1) - F1-6 (SN1) Always Below 1 ohms CURRENT P SENSOR FAIL MODE 3 Tester connection Condition Specified condition F6-1 (SN2) - F1-2 (SN2) Always Below 1 ohms CURRENT P SENSOR FAIL MODE 4 Tester connection Condition Specified condition F6-1 (SN2) - F1-2 (SN2) Always Below 1 ohms F6-8 (SN1) - F1-6 (SN1) Always Below 1 ohms CURRENT P SENSOR FAIL MODE 5 Tester connection Condition Specified condition F6-1 (SN2) - F1-2 (SN2) Always Below 1 ohms F6-3 (VCC) - F1-5 (VCC) Always Below 1 ohms F6-8 (SN1) - F1-6 (SN1) Always Below 1 ohms F6-14 (SGD) - F1-4 (SGD) Always Below 1 ohms CURRENT P SENSOR FAIL MODE 6 Tester connection Condition Specified condition F6-1 (SN2) - F1-2 (SN2) Always Below 1 ohms F6-3 (VCC) - F1-5 (VCC) Always Below 1 ohms F6-8 (SN1) - F1-6 (SN1) Always Below 1 ohms F6-14 (SGD) - F1-4 (SGD) Always Below 1 ohms Standard Resistance (Check for Short) CURRENT P SENSOR FAIL MODE 1 Tester connection Condition Specified condition F6-3 (VCC) - Body ground Always 10 kohms or higher F6-14 (SGD) - Body ground Always 10 kohms or higher CURRENT P SENSOR FAIL MODE 2 Tester connection Condition Specified condition F6-8 (SN1) - Body ground Always 10 kohms or higher CURRENT P SENSOR FAIL MODE 3 Tester connection Condition Specified condition F6-1 (SN2) - Body ground Always 10 kohms or higher CURRENT P SENSOR FAIL MODE 4 Tester connection Condition Specified condition F6-1 (SN2) - Body ground Always 10 kohms or higher F6-8 (SN1) - Body ground Always 10 kohms or higher CURRENT P SENSOR FAIL MODE 5 Tester connection Condition Specified condition F6-1 (SN2) - Body ground Always 10 kohms or higher F6-3 (VCC) - Body ground Always 10 kohms or higher F6-8 (SN1) - Body ground Always 10 kohms or higher F6-14 (SGD) - Body ground Always 10 kohms or higher CURRENT P SENSOR FAIL MODE 6 Tester connection Condition Specified condition F6-1 (SN2) - Body ground Always 10 kohms or higher F6-3 (VCC) - Body ground Always 10 kohms or higher F6-8 (SN1) - Body ground Always 10 kohms or higher F6-14 (SGD) - Body ground Always 10 kohms or higher NG --> REPAIR OR REPLACE HARNESS OR CONNECTOR OK: Go to next step
  8. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY Remove the power window regulator motor assembly. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S19549818492014042900000) . Inspect the power window regulator motor assembly. Refer to «INSPECTION [07/2013 - ]»(ref-612430-S39510651692014042900000) . NG --> See step 12 OK: Go to next step
  9. REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY Temporarily replace the power window regulator switch assembly with a new or normally functioning one. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S29215901522014042900000) . Check the power window regulator switch assembly operates. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Front passenger side door power window operates normally. RESULT Result Proceed to Does not operate A Operates B B --> END A: Go to next step
  10. REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Temporarily replace the power window regulator master switch assembly with a new or normally functioning one. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S08305805372014042900000) . Check the power window regulator master switch assembly operates. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Driver door power window operates normally. RESULT Result Proceed to Does not operate A Operate B B --> END A --> REPLACE POWER WINDOW REGULATOR ASSEMBLY
  11. REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S08305805372014042900000)
  12. REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S19549818492014042900000)
  1. CHECK DTC OUTPUT Clear the DTCs. Refer to «DTC CHECK / CLEAR [07/2013 - ]»(ref-612250-S01413683982014042900000) . Check the DTCs. Refer to «DTC CHECK / CLEAR [07/2013 - ]»(ref-612250-S01413683982014042900000) . RESULT Result Proceed to DTC B2312 is output A DTC B2315 is output B B --> See step 2 A --> See step 5
  2. READ VALUE USING TECHSTREAM Connect the Techstream to the DLC3. Turn the ignition switch to ON. Turn the Techstream on. Enter the following menus: Body Electrical / Master Switch / Data List. According to the display on the Techstream, read the Data List. MASTER SWITCH Tester Display Measurement Item/Range Normal Condition Diagnostic Note P Door P/W Auto SW Front passenger side power window auto switch signal / ON or OFF ON: Front passenger side power window auto up/down switch operated OFF: Front passenger side power window switch not operated - P Door P/W Up SW Front passenger side power window manual up signal / ON or OFF ON: Front passenger side power window manual up switch operated OFF: Front passenger side power window switch not operated - P Door P/W Down SW Front passenger side power window manual down signal / ON or OFF ON: Front passenger side power window manual down switch operated OFF: Front passenger side power window switch not operated - OK The Techstream display changes normally when master switch is operated. NG --> See step 4 OK: Go to next step
  3. CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR SWITCH ASSEMBLY) Disconnect the E8 power window regulator master switch assembly connector. Disconnect the F6 power window regulator switch assembly connector. Measure the resistance according to the value(s) in the table below. Standard Resistance (Check for Open) Tester Connection Condition Specified Condition E8-2 (UART) - F6-2 (UART) Always Below 1 ohms Standard Resistance (Check for Short) Tester Connection Condition Specified Condition E8-2 (UART) - Body ground Always 10 kohms or higher NG --> REPAIR OR REPLACE HARNESS OR CONNECTOR OK --> See step 5
  4. REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S29215901522014042900000)
  5. REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S08305805372014042900000)
  1. PERFORM INITIALIZATION Turn the ignition switch to ON. Initialize the power window regulator master switch assembly or power window regulator switch assembly. Refer to «INITIALIZATION [07/2013 - ]»(ref-612250-S35237050992014042900000) . NEXT: Go to next step
  2. CHECK DTC OUTPUT Clear the DTCs. Refer to «DTC CHECK / CLEAR [07/2013 - ]»(ref-612250-S01413683982014042900000) . Check for DTCs. Refer to «DTC CHECK / CLEAR [07/2013 - ]»(ref-612250-S01413683982014042900000) . HINT: Check for DTCs for the power window regulator master switch assembly or power window regulator switch assembly that has DTC B2313 or B2316 stored in its ECU. OK DTC B2313 or B2316 is not output. RESULT Result Proceed to No DTCs output A DTC B2311 or B2314 is output B DTC B2312 or B2315 is output B DTC B2313 is output C DTC B2316 is output D B --> See step 5 C --> See step 3 D --> See step 4 A --> END (POWER WINDOW CONTROL SYSTEM HAS NOT BEEN INITIALIZED)
  3. REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side). Refer to «REMOVAL [07/2013 - ]»(ref-612430-S19549818492014042900000)
  4. REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side). Refer to «REMOVAL [07/2013 - ]»(ref-612430-S19549818492014042900000)
  5. GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table). Refer to «PROBLEM SYMPTOMS TABLE [07/2013 - ]»(ref-612250-S33647848842014042900000)
  1. CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (WINDOW LOCK SWITCH) Turn the window lock switch off and operate the switches on the power window regulator master switch assembly. Check that the remote UP/DOWN function operates normally. OK Remote UP/DOWN function operates normally. NG --> See step 4 OK: Go to next step
  2. READ VALUE USING TECHSTREAM Connect the Techstream to the DLC3. Turn the ignition switch to ON. Turn the Techstream on. Enter the following menus: Body Electrical / Main Body / Data List. Read the Data List according to the display on the Techstream. MASTER SWITCH Tester Display Test Part Control Range Diagnostic Note P Door P/W Remote Auto SW Front passenger side power window auto switch signal from driver side / ON or OFF ON: Front passenger side power window auto up/down switch from driver side operated OFF: Front passenger side power window switch from driver side not operated - P Door P/W Remote Up SW Front passenger side power window manual up signal from driver side / ON or OFF ON: Front passenger side power window manual up switch from driver side operated OFF: Front passenger side power window switch from driver side not operated - P Door P/W Remote Down SW Front passenger side power window manual down switch from driver side /OFF or ON ON: Front passenger side power window manual down switch from driver side operated OFF: Front passenger side power window switch from driver side not operated - OK The Techstream display changes normally when master switch is operated. NG --> See step 4 OK: Go to next step
  3. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR SWITCH ASSEMBLY) Disconnect the E8 power window regulator master switch assembly connector. Disconnect the F6 power window regulator switch assembly connector. Measure the resistance according to the value(s) in the table below. Standard Resistance (Check for Open) Tester Connection Condition Specified Condition E8-2 (UART) - F6-2 (UART) Always Below 1 ohms Standard Resistance (Check for Short) Tester Connection Condition Specified Condition E8-2 (UART) - Body ground Always 10 kohms or higher NG --> REPAIR OR REPLACE HARNESS OR CONNECTOR OK --> See step 5
  4. REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S08305805372014042900000)
  5. REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S29215901522014042900000)
  1. PERFORM ACTIVE TEST USING TECHSTREAM Connect the Techstream to the DLC3. Turn the ignition switch to ON. Turn the Techstream on. Enter the following menus: Body Electrical / Master Switch / Active Test. Perform the Active Test according to the display on the Techstream. MASTER SWITCH Tester Display Test Part Control Range Diagnostic Note Power Window Driver side power window OFF / UP / DOWN - OK Driver door power window operates normally. WARNING: Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate. RESULT Result Proceed to NG A OK B B --> See step 6 A: Go to next step
  2. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY) Disconnect the E8 power window regulator master assembly connector. Measure the voltage and resistance according to the value(s) in the table below. Standard Voltage Tester Connection Condition Specified Condition E8-12 (+B) - Body ground Always 11 to 14 V Standard Resistance Tester Connection Condition Specified Condition E8-5 (GND) - Body ground Always Below 1 ohms TEXT IN ILLUSTRATION *a Front view of wire harness connector (to Power Window Regulator Master Switch Assembly) NG --> REPAIR OR REPLACE HARNESS OR CONNECTOR OK: Go to next step
  3. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY) Disconnect the E8 power window regulator master switch assembly connector. Disconnect the E5 power window regulator motor assembly connector. Measure the resistance according to the value(s) in the table below. Standard Resistance (Check for Open) Tester Connection Condition Specified Condition E8-6 (WU) - E5-1 (WU) Always Below 1 ohms E8-7 (WD) - E5-3 (WD) Always Below 1 ohms Standard Resistance (Check for Short) Tester Connection Condition Specified Condition E8-6 (WU) - Body ground Always Below 1 ohms E8-7 (WD) - Body ground Always Below 1 ohms NG --> REPAIR OR REPLACE HARNESS OR CONNECTOR OK: Go to next step
  4. REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Temporarily replace the power window regulator master switch assembly with a new or normally functioning one. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S08305805372014042900000) . Check the power window regulator master switch assembly operates. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Driver door power window operates normally. RESULT Result Proceed to Operate A Does not operate B B --> See step 5 A --> END (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WAS DEFECTIVE)
  5. REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S19549818492014042900000)
  6. REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S08305805372014042900000)
  1. PERFORM ACTIVE TEST USING TECHSTREAM Connect the Techstream to the DLC3. Turn the ignition switch to ON. Turn the Techstream on. Enter the following menus: Body Electrical / Master Switch / Active Test. Perform the Active Test according to the display on the Techstream. MASTER SWITCH Tester Display Test Part Control Range Diagnostic Note Power Window Front passenger side power window OFF / UP / DOWN - OK Front passenger side door power window operates normally. WARNING: Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate. RESULT Result Proceed to NG A OK B B --> See step 6 A: Go to next step
  2. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - BATTERY) Disconnect the F6 power window regulator switch assembly connector. Measure the voltage and resistance according to the value(s) in the table below. Standard Voltage Tester Connection Condition Specified Condition F6-12 (+B) - Body ground Always 11 to 14 V Standard Resistance Tester Connection Condition Specified Condition F6-5 (GND) - Body ground Always Below 1 ohms TEXT IN ILLUSTRATION *a Front view of wire harness connector (to Front Power Window Regulator Switch Assembly) NG --> REPAIR OR REPLACE HARNESS OR CONNECTOR OK: Go to next step
  3. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW MOTOR ASSEMBLY) Disconnect the F6 power window regulator switch assembly connector. Disconnect the F1 power window regulator motor assembly connector. Measure the resistance according to the value(s) in the table below. Measure the resistance according to the value(s) in the table below. Standard Resistance (Check for Open) Tester Connection Condition Specified Condition F6-6 (WU) - F1-1 (WU) Always Below 1 ohms F6-7 (WD) - F1-3 (WD) Always Below 1 ohms Standard Resistance (Check for Short) Tester Connection Condition Specified Condition F6-6 (WU) - Body ground Always 10 kohms or higher F6-7 (WD) - Body ground Always 10 kohms or higher NG --> REPAIR OR REPLACE HARNESS OR CONNECTOR OK: Go to next step
  4. REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY Temporarily replace the power window regulator switch assembly with a new or normally functioning one. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S29215901522014042900000) . Check the power window regulator switch assembly operates. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Front passenger side door power window operates normally. RESULT Result Proceed to Operates A Does not operate B B --> See step 5 A --> END (POWER WINDOW REGULATOR SWITCH ASSEMBLY WAS DEFECTIVE)
  5. REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S19549818492014042900000)
  6. REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S29215901522014042900000)
  1. READ VALUE USING TECHSTREAM Connect the Techstream to the DLC3. Turn the ignition switch to ON. Turn the Techstream on. Enter the following menus: Body Electrical / Master Switch / Active Test. Perform the Active Test according to the display on the Techstream. MASTER SWITCH Tester Display Test Part Control Range Diagnostic Note D Door P/W Auto SW Driver side power window auto switch signal / ON or OFF ON: Driver side power window auto up/down switch operated OFF: Driver side power window switch not operated - OK The Techstream display changes normally when master switch is operated. NG --> See step 3 OK: Go to next step
  2. PERFORM INITIALIZATION Initialize the power window regulator motor assembly. Refer to «INITIALIZATION [07/2013 - ]»(ref-612250-S35237050992014042900000) . Check that the driver side door power window moves when the auto up and down function of the power window master switch assembly is operated. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Driver side auto up and down function is normal. NG --> See step 4 OK --> END (PROBLEM DUE TO INITIALIZATION FAILURE)
  3. REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Temporarily replace the power window regulator master switch assembly with a new or normally functioning one. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S08305805372014042900000) . Check the power window regulator master switch assembly operates. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Driver door power window operates normally. RESULT Result Proceed to Operate A Does not operate B B --> See step 4 A --> END (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WAS DEFECTIVE)
  4. REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S19549818492014042900000)
  1. READ VALUE USING TECHSTREAM Connect the Techstream to the DLC3. Turn the ignition switch to ON. Turn the Techstream on. Enter the following menus: Body Electrical / Master Switch / Active Test. Perform the Active Test according to the display on the Techstream. MASTER SWITCH Tester Display Test Part Control Range Diagnostic Note P Door P/W Auto SW Front passenger side power window auto switch signal / ON or OFF ON: Front passenger side power window auto up/down switch operated OFF: Front passenger side power window switch not operated - OK The Techstream display changes normally when regulator switch is operated. NG --> See step 3 OK: Go to next step
  2. PERFORM INITIALIZATION Initialize the power window regulator motor assembly. Refer to «INITIALIZATION [07/2013 - ]»(ref-612250-S35237050992014042900000) . Check that the front passenger side door power window moves when the auto up and down functions of the power window regulator switch assembly are operated. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Front passenger side auto up and down functions are normal. NG --> See step 4 OK --> END (PROBLEM DUE TO INITIALIZATION FAILURE)
  3. REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY Temporarily replace the power window regulator switch assembly with a new or normally functioning one. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S29215901522014042900000) . Check the power window regulator switch assembly operates. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Front passenger side door power window operates normally. RESULT Result Proceed to Operates A Does not operate B B --> See step 4 A --> END (POWER WINDOW REGULATOR SWITCH ASSEMBLY WAS DEFECTIVE)
  4. REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S29215901522014042900000)
  1. CHECK OPERATION FUNCTION AFTER IGNITION SWITCH IS TURNED OFF Check the power window master switch assembly operation function after the ignition switch is turned off. RESULT Result Proceed to When power window can still be operated even after opening driver or front passenger side door within approximately 45 seconds of ignition switch being turned off A When power window can still be operated even after approximately 45 seconds have elapsed after ignition switch turned off (for All Doors) B When power window can still be operated even after approximately 45 seconds have elapsed after ignition switch turned off (for Driver Side) B Check the power window switch assembly operation function after the ignition switch is turned off. RESULT Result Proceed to When power window can still be operated even after opening driver or front passenger side door within approximately 45 seconds of ignition switch being turned off C When power window can still be operated even after approximately 45 seconds have elapsed after ignition switch turned off (for Front Passenger Side) D B --> See step 9 C --> See step 3 D --> See step 4 A: Go to next step
  2. READ VALUE USING TECHSTREAM (DOOR COURTESY SWITCH) Connect the Techstream to the DLC3. Turn the ignition switch to ON. Turn the Techstream on. Enter the following menus: Body Electrical / Master Switch / Data List. According to the display on the Techstream, read the Data List. MASTER SWITCH Tester Display Measurement Item/Range Normal Condition Diagnostic Note D Door Courtesy SW Driver side door courtesy light switch signal / ON or OFF ON: Driver side door opened OFF: Driver side door closed - OK Normal conditions listed above are displayed. NG --> See step 7 OK --> See step 9
  3. READ VALUE USING TECHSTREAM Connect the Techstream to the DLC3. Turn the ignition switch to ON. Turn the Techstream on. Enter the following menus: Body Electrical / Master Switch / Data List. According to the display on the Techstream, read the Data List. MASTER SWITCH Tester Display Measurement Item/Range Normal Condition Diagnostic Note P Door Courtesy SW Front passenger side door courtesy light switch signal / ON or OFF OK: Front passenger side door opened NG: Front passenger side door closed - OK Normal conditions listed above are displayed. NG --> See step 7 OK --> See step 8
  4. CHECK OPERATION (POWER WINDOW SWITCH) Check the power window regulator master switch assembly and power window regulator switch assembly operation function after the ignition switch is off. RESULT Result Proceed to Operate (for both driver side and front passenger side switches) A Operate (for driver side switch only) A Operate (for front passenger side switch only) B B --> See step 6 A: Go to next step
  5. REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Remove the power window regulator master switch assembly. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S08305805372014042900000) . Check the power window regulator master switch assembly operates. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Driver door power window operates normally. RESULT Result Proceed to Does not Operate A Operate B B --> END A --> See step 8
  6. REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY Remove the power window regulator switch assembly. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S29215901522014042900000) . Check the power window regulator switch assembly operates. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Front passenger side door power window operates normally. RESULT Result Proceed to Does not Operate A Operate B B --> END A --> See step 9
  7. GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit). Refer to «Door Courtesy Switch Circuit»(ref-612235-S25117520592014042900000)
  8. REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S29215901522014042900000)
  9. REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S08305805372014042900000)
  1. PERFORM INITIALIZATION (APPLICABLE LOCATION) Initialize the power window regulator motor assembly (applicable location). Refer to «INITIALIZATION [07/2013 - ]»(ref-612250-S35237050992014042900000) . Check that all the power windows move when the auto up and down function of the power window regulator master switch assembly and power window regulator switch assemblies are operated. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Auto up and down function is normal NG --> See step 2 OK --> END (PROBLEM DUE TO INITIALIZATION FAILURE)
  2. CHECK WINDOW GLASS SLIDING MOVEMENT (APPLICABLE LOCATION) Remove the window regulator motor assembly. Install the window glass onto the weatherstrip. Check if the door window regulator operates smoothly. Check that the window glass slides smoothly when sliding it up by hand. OK Door window glass slides smoothly. WARNING: Perform initialization again. HINT: Ensure the following: The window glass fits with the weatherstrip without improper contact or deformation. Foreign objects are not caught in the weatherstrip. NG --> FIT WINDOW GLASS CORRECTLY (REMOVE FOREIGN OBJECTS CAUSING IMPROPER FIT OR REPLACE PARTS) OK --> See step 3
  3. REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S19549818492014042900000)
  1. READ VALUE USING TECHSTREAM (D Door Courtesy SW) Connect the Techstream to the DLC3. Turn the ignition switch to ON. Turn the Techstream on. Enter the following menus: Body Electrical / Main Body / Data List. Read the Data List according to the display on the Techstream. MASTER SWITCH Tester Display Test Part Control Range Diagnostic Note D Door Courtesy SW Driver side door courtesy light switch signal / ON or OFF ON: Driver side door opened OFF: Driver side door closed - OK On the Techstream screen, ON or OFF is displayed accordingly. NG --> See step 8 OK: Go to next step
  2. PERFORM INITIALIZATION Initialize the power window regulator master switch assembly. Refer to «INITIALIZATION [07/2013 - ]»(ref-612250-S35237050992014042900000) . Check the power window regulator master switch assembly is operated. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Driver side door power window operates normally. RESULT Result Proceed to NG A OK B B --> END A: Go to next step
  3. READ VALUE USING TECHSTREAM Connect the Techstream to the DLC3. Turn the ignition switch to ON. Turn the Techstream on. Enter the following menus: Body Electrical / Main Body / Data List. Read the Data List according to the display on the Techstream. MASTER SWITCH Tester Display Test Part Control Range Diagnostic Note Current D Door Glass Position Information Glass position of the driver side power window / -100 to 700 - - OK Pulse generation. NG --> See step 6 OK: Go to next step
  4. CHECK POWER WINDOW REGULATOR ASSEMBLY Check the power window regulator master switch assembly operates. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Driver side door power window operates normally. RESULT Result Proceed to Operate (Does not window glass operate) A Does not operate B B --> REPLACE POWER WINDOW REGULATOR ASSEMBLY A: Go to next step
  5. REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY Temporarily replace the power window regulator motor assembly with a new or normally functioning one. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S19549818492014042900000) . Check the power window regulator master switch assembly operates. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Driver side door power window operates normally. RESULT Result Proceed to Operate A Does not operate B B --> See step 9 A --> END
  6. REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Temporarily replace the power window regulator master switch assembly with a new or normally functioning one. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S08305805372014042900000) . Check the power window regulator master switch assembly operates. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Driver side door power window operates normally. RESULT Result Proceed to Does not operate A Operate B B --> END A: Go to next step
  7. REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY Temporarily replace the power window regulator motor assembly with a new or normally functioning one. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S19549818492014042900000) . Check the power window regulator master switch assembly operates. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Driver side door power window operates normally. RESULT Result Proceed to Operate A Does not operate B B --> REPLACE POWER WINDOW REGULATOR ASSEMBLY A --> END
  8. GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit). Refer to «Door Courtesy Switch Circuit»(ref-612235-S25117520592014042900000)
  9. REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S08305805372014042900000)
  1. READ VALUE USING TECHSTREAM (D Door Courtesy SW) Connect the Techstream to the DLC3. Turn the ignition switch to ON. Turn the Techstream on. Enter the following menus: Body Electrical / Main Body / Data List. Read the Data List according to the display on the Techstream. MASTER SWITCH Tester Display Test Part Control Range Diagnostic Note P Door Courtesy SW Front passenger side door courtesy light switch signal / ON or OFF ON: Front passenger side door opened OFF: Front passenger side door closed - OK On the Techstream screen, ON or OFF is displayed accordingly. NG --> See step 8 OK: Go to next step
  2. PERFORM INITIALIZATION Initialize the power window regulator switch assembly. Refer to «INITIALIZATION [07/2013 - ]»(ref-612250-S35237050992014042900000) . Check the power window regulator switch assembly is operated. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Front passenger side door power window operates normally. RESULT Result Proceed to NG A OK B B --> END A: Go to next step
  3. READ VALUE USING TECHSTREAM Connect the Techstream to the DLC3. Turn the ignition switch to ON. Turn the Techstream on. Enter the following menus: Body Electrical / Main Body / Data List. Read the Data List according to the display on the Techstream. MASTER SWITCH Tester Display Test Part Control Range Diagnostic Note Current P Door Glass Position Information Glass position of the passenger side power window / -100 to 700 - - OK Pulse generation. NG --> See step 6 OK: Go to next step
  4. CHECK POWER WINDOW REGULATOR ASSEMBLY Check the power window regulator switch assembly operates. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Front passenger side door power window operates normally. RESULT Result Proceed to Operate (Does not window glass operate) A Does not operate B B --> REPLACE POWER WINDOW REGULATOR ASSEMBLY A: Go to next step
  5. REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY Temporarily replace the power window regulator motor assembly with a new or normally functioning one. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S19549818492014042900000) . Check the power window regulator switch assembly operates. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Front passenger side door power window operates normally. RESULT Result Proceed to Operate A Does not operate B B --> See step 9 A --> END
  6. REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY Temporarily replace the power window regulator switch assembly with a new or normally functioning one. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S29215901522014042900000) . Check the power window regulator switch assembly operates. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Front passenger side door power window operates normally. RESULT Result Proceed to Does not operate A Operate B B --> END A: Go to next step
  7. REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY Temporarily replace the power window regulator motor assembly with a new or normally functioning one. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S19549818492014042900000) . Check the power window regulator switch assembly operates. Refer to «OPERATION CHECK [07/2013 - ]»(ref-612250-S14124706882014042900000) . OK Front passenger side door power window operates normally. RESULT Result Proceed to Operate A Does not operate B B --> REPLACE POWER WINDOW REGULATOR ASSEMBLY A --> END
  8. GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit). Refer to «Door Courtesy Switch Circuit»(ref-612235-S25117520592014042900000)
  9. REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY. Refer to «REMOVAL [07/2013 - ]»(ref-612430-S29215901522014042900000)

More articles — Power Window Control System (Diagnostic Codes & Symptom Tests)