Programming and Setup - All Systems: Removal & Installation Saturn Aura I

Communication Interface Module Replacement

If the OnStar® communication interface module is replaced, the setup procedure needs to be performed. Please refer to OnStar Reconfiguration (with TIS 2 Web Gen 4 and later) .

Radio Replacement

If the digital radio receiver is replaced, the following procedure must be performed

Perform the digital radio receiver setup. Refer to Digital Radio Receiver Setup .

EBCM Replacement

If the electronic brake control module (EBCM) is replaced it must be programmed. Refer to Service Programming System (SPS) .

ECM Replacement

If the engine control module (ECM) is replaced, the following procedures must be performed

1. ECM Reprogramming-Refer to «Service Programming System (SPS)»(ref-301518-S05487699242008101700000) .
2. The CKP System Variation Learn-Refer to the following: «Crankshaft Position System Variation Learn»(ref-301531-S28039219932008101700000) for the 2.4L engine «Crankshaft Position System Variation Learn»(ref-301532-S35056917632008101700000) for the 3.5L engine «Crankshaft Position System Variation Learn»(ref-301503-S36070069802008101700000) for the 3.6L engine
3. Engine Oil Life Remaining-When available, use a scan tool to reset the Engine Oil Life Remaining back to the original percentage recorded before the module was replaced.
4. Transmission Fluid Life Remaining-When available, use the scan tool to reset the Transmission Fluid Life Remaining back to the original percentage recorded before the module was replaced.
5. Theft Deterrent-Refer to «Immobilizer System Component Programming»(ref-301537-S15013665442008101700000) .

Setup for Component Replacement

The replacement of some components will require a setup procedure for complete repair.

If any of the following components are replaced, the CKP Variation Learn Procedure must be performed

1. Engine replacement
2. Any engine repair that disturbs the CKP sensor or its relationship with the crankshaft reluctor wheel
3. CKP sensor

Refer to the following

1. «Crankshaft Position System Variation Learn»(ref-301531-S28039219932008101700000) for the 2.4L engine
2. «Crankshaft Position System Variation Learn»(ref-301532-S35056917632008101700000) for the 3.5L engine
3. «Crankshaft Position System Variation Learn»(ref-301503-S36070069802008101700000) for the 3.6L engine

HVAC Control Module Replacement - Automatic HVAC

If the HVAC control module is replaced, the following procedure must be performed

Re-Calibrating actuators-Refer to Actuator Recalibration .

Actuator Replacement - Automatic HVAC

If an actuator is replaced, the following procedure must be performed

Re-Calibrating actuators-Refer to Actuator Recalibration .

HVAC Control Module Replacement - Manual HVAC

If the HVAC control module is replaced no additional procedures are necessary.

Actuator Replacement - Manual HVAC

If an actuator is replaced, a re-calibration of the actuator is not necessary. The HVAC module knows the exact location of the door when the HVAC system is turned on.

If the radio is replaced, the new radio must have the setup procedure performed. Refer to Radio Setup .

Remote Control Door Lock Receiver Replacement-Copy and Paste TPM Information

This procedure will learn the TPM information to the new RCDLR using the Copy and Paste function on the scan tool. The procedure will extract the TPM Tire Type information as well as the sensor data from the existing RCDLR prior to its replacement and store this information in the scan tool. After RCDLR replacement, the tire type and sensor data stored in the scan tool is written to the new RCDLR, negating the need to perform the tire type setup and sensor learn procedure.

This procedure should be considered as the first programming choice when replacing an RCDLR. The Copy and Paste procedure eliminates the possibility of incorrectly inputting the tire type or learning stray TPM sensors.

1. Using a scan tool, navigate to the Copy and Paste TPM Information procedure and copy the existing TPM information from the RCDLR using the outline below. Follow the on-screen instructions after selecting Step 1: Vehicle Control Systems Module Setup Remote Control Door Lock Receiver Copy and Paste TPM Information Step 1
2. At this point, install the new RCDLR.
3. Using a scan tool, navigate to the Copy and Paste TPM Information procedure to paste the stored TPM information using the outline below. Follow the on-screen instructions after selecting Step 2: Vehicle Control Systems Module Setup Remote Control Door Lock Receiver Copy and Paste TPM Information Step 2
4. Program the keyless entry transmitters. Refer to «Transmitter Programming»(ref-301522-S00404519042008101700000) .
5. Setup the new RCDLR: Select Remote Control Door Lock Receiver under Module Setup in the scan tool Vehicle Control System menu. Select Setup New RCDLR. Follow the on-sceen instructions.

Remote Control Door Lock Receiver Replacement-TPM Sensor Learn

This procedure will learn TPM information to the new RCDLR by manually inputting the tire type using the scan tool and performing the TPM sensor learn. This procedure should be performed if the above Copy and Paste procedure can not be completed. An example of this would be an RCDLR that is unable to communicate with the scan tool and is required to be replaced.

1. Program the keyless entry transmitters. Refer to «Transmitter Programming»(ref-301522-S00404519042008101700000) .
2. Setup the new RCDLR: Select Remote Control Door Lock Receiver under Module Setup in the scan tool Vehicle Control System menu. Select Setup New RCDLR. Follow the on-sceen instructions.
3. Tire Type Setup: Install a scan tool. Select Remote Control Door Lock Receiver under Module Setup in the Vehicle Control System menu. Select Tire Type/Pressure Selection. Follow the on-sceen instructions.
4. Tire Pressure Monitoring Sensor Learn-Refer to «Tire Pressure Sensor Learn»(ref-301538-S01160832552008101700000) .