Home/Saab/9-7X/Saab 9-7X I (2005-2009)/Repair manual/Automatic HVAC System/Heating, Ventilation, and Air Conditioning: Specifications

Contents

Wiring diagrams Section: Automatic HVAC System

All sections

Heating, Ventilation, and Air Conditioning: Specifications Saab 9-7X I

Automatic HVAC System

Fastener Tightening Specifications

Application	Specification
Application	Metric	English
A/C Compressor Cycling Switch	5 N.m	44 lb in
A/C Compressor Mounting Bolt	50 N.m	37 lb ft
A/C Compressor Rear Bracket Bolt	25 N.m	18 lb ft
A/C Evaporator and Blower Module Shield Screws	2.2 N.m	19 lb in
A/C Refrigerant Pressure Sensor	4.8 N.m	42 lb in
Accumulator Clamp Screw	10 N.m	88 lb in
Accumulator to Evaporator Fitting	28 N.m	21 lb ft
Air Distributor Duct Mounting Screw	1.9 N.m	17 lb in
Air Inlet Assembly Mounting Stud	4.5 N.m	40 lb in
Air Outlet Assembly Retaining Screw	2.5 N.m	22 lb in
Air Temperature Actuator Retaining Screw	1.9 N.m	17 lb in
Blower Assembly Mounting Nut (RPO C42)	4.5 N.m	40 lb in
Blower Assembly Mounting Screw (RPO C42)	4.5 N.m	40 lb in
Blower Assembly Mounting Stud (RPO C42)	4.5 N.m	40 lb in
Blower Motor Access Cover Screw (RPO C60 and C68)	2.5 N.m	22 lb in
Blower Motor and Fan Assembly Mounting Screw	1.9 N.m	17 lb in
Blower Motor Relay Bracket Mounting Screw	1.9 N.m	17 lb in
Blower Motor Resistor Mounting Screw	1.9 N.m	17 lb in
Body Harness Connector Support Bracket Mounting Nuts	9.0 N.m	80 lb in
Compressor Discharge Hose to Condenser Fitting	28 N.m	21 lb ft
Compressor Pressure Relief Valve	9 N.m	80 lb in
Compressor Suction/Discharge Hose to Compressor Bolt	33 N.m	24 lb ft
Compressor Suction Hose to Accumulator Fitting	48 N.m	35 lb ft
Condenser Insulator Retaining Screw	1.9 N.m	17 lb in
Evaporator Case Section to Blower Case Section Retaining Screw	1.9 N.m	17 lb in
Evaporator Tube Clip Screw	1.9 N.m	17 lb in
Evaporator Tube to Condenser Fitting	28 N.m	21 lb ft
Floor Air Outlet Mounting Screw	1.9 N.m	17 lb in
Heater Core Access Cover Screw	1.9 N.m	17 lb in
Heater Inlet and Outlet Hoses Bracket Bolt	25 N.m	18 lb ft
Heater Inlet Hose Fitting at Intake Manifold	23.5 N.m	17 lb ft
Heater Outlet Hose Bracket Bolt	25 N.m	18 lb ft
Heater/Vent Module Mounting Nut	4.5 N.m	40 lb in
Heater/Vent Module Mounting Screw	4.5 N.m	40 lb in
Heater/Vent Module Mounting Stud	4.5 N.m	40 lb in
Intermediate Bracket Bolts	10 N.m	88 lb in
Knee Bolster Bracket Nuts	5.5 N.m	49 lb in

Fastener Tightening Specifications

Refrigerant System Capacities

Application	Specification
Application	Metric	English
PAG Oil GM P/N 12345923 (Canadian P/N 10953486)
Accumulator Replacement	60 ml*	2 oz*
*Add PAG oil equal to the amount of oil drained from the old accumulator plus the specified additional amount.
Compressor Replacement	60 ml 1	2 oz 1
A Sanden scroll compressor containing 240 ml 1 of oil is used on this model year.
Condenser Replacement	30 ml 1	1 oz 1
Evaporator Replacement	90 ml 1	3 oz 1
Total System Oil Capacity	240 ml	8 oz
Refrigerant Charge R-134a	0.86 kg	1.9 lb
1 If more than the specified amount of oil was drained from a component, add the equal amount of oil drained.

Refrigerant System Capacities