FLUID CAPACITIES
Transaxle fluid capacities in TRANSAXLE FLUID CAPACITIES table are approximate system quantities. Correct fluid level should be determined using dipstick.
| Application | Drain & Refill (2) - Qts. (L) | Overhaul - Qts. (L) |
|---|---|---|
| AW50-40LE | 2.6-3.1 (2.5-3.0) | 5.8-6.3 (5.5-6.0) |
| (1) Fluid capacities listed are approximate. Always fill to specified area on dipstick (if equipped). (2) Drain and refill capacity does not include torque converter. | ||
| (1) | Fluid capacities listed are approximate. Always fill to specified area on dipstick (if equipped). |
| (2) | Drain and refill capacity does not include torque converter. |
TRANSAXLE FLUID CAPACITIES (1)
Torque Converter Clutch Does Not Engage
Possible cause: torque converter clutch solenoid defective, valve body defective or torque converter clutch defective.
TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) |
|---|---|
| Cooler Line Bolt | 26 (35) |
| Drain Plug | 17-40 (23-55) |
| Oil Pan Bolt | 22 (30) |
| Park/Neutral Position Switch Lever Nut | 18 (25) |
| Ring Gear Bolt | 66-76 (90-103) |
| TFT Protector Bolt | 15-22 (20-29) |
| Transaxle Case Bolt | 17-26 (23-35) |
| Underdrive Brake Band Anchor Bolt | 100-149 (133-200) |
| Valve Body Cover Bolt | 18 (25) |
| INCH Lbs. (N.m) | |
| Accumulator Piston Cover Bolt | 71-106 (8-12) |
| Input Shaft Speed Sensor Bolt | 4-7 (35-62) |
| Lube Apply Clamp Bolt | 35-62 (4-7) |
| Oil Filter Bolt | 35-62 (4-7) |
| Oil Reserver Bolt | 35-62 (4-7) |
| Park/Neutral Position Switch Bolt | 53-71 (6-8) |
| Solenoid-To-Valve Body Bolt | 6-7 (53-62) |
| Stator Support-To-Oil Pump 5-mm Bolt | 6-7 (53-62) |
| Stator Support-To-Oil Pump 6-mm Bolt | 89-124 (10-14) |
| Underdrive Brake Accumulator Bracket Bolt | 71-106 (8-12) |
| Valve Body Bolt | 62 (7) |
| Valve Body Suction Cover Bolt | 62 (7) |
TORQUE SPECIFICATIONS
TRANSAXLE SPECIFICATIONS
| Application | In. (mm) | |
|---|---|---|
| Differential Assembly | ||
| Pinion Gear Backlash | .002-.006 (.05-.15) | |
| Input Shaft End Play | 005-.035 (.37-.90) | |
| Oil Pump Bushing | ||
| Diameter | 1.500-1.501 (38.11-38.14) | |
| Wear Limit | 1.503 (38.18) | |
| Oil Pump Gear Side Clearance | ||
| Drive Gear | .0001-.0120 (.004-.298) | |
| Driven Gear | .003-.006 (.08-.15) | |
| Oil Pump Thrust Clearance | ||
| Standard | .001-.002 (.03-.05) | |
| Wear Limit | .004 (.10) | |
| Piston Stroke | ||
| 2nd Brake Clutch | .045-.073 (1.14-1.86) | |
| 2nd Coast Clutch | .029-.056 (.76-1.44) | |
| Direct Clutch | .059-.074 (1.52-1.89) | |
| Forward Clutch | .059-.074 (1.52-1.89) | |
| Low/Reverse Clutch | .069-.100 (1.75-2.55) | |
| Underdrive Clutch | .059-.074 (1.52-1.89) | |
| Planetary Gear Bushing | ||
| Specified Clearance | 1.181-1.182 (30.00-30.80) | |
| Service Limit | 1.184 (30.08) | |
| Sun Gear Bushing | ||
| Specified Clearance | .846-.848 (21.50-21.53) | |
| Service Limit | .850 (21.58) | |
| Stator Shaft Bushing | ||
| Diameter | .846-.848 (21.50-21.53) | |
| Wear Limit | .850 (21.58) | |
| Underdrive Sun Gear Bushing | ||
| Specified Clearance | .846-.848 (21.50-21.53) | |
| Service Limit | .850 (21.58) | |
TRANSAXLE SPECIFICATIONS