Manual sections
Wiring diagrams- Battery
- Body
- Braking
- Comfort and convenience
- Confort
- Current generation
- Dashboard
- Electrical harnesses
- Engine
- Front anti -roll bar
- Front axle
- Front doors
- Front seats
- Front section
- Front shock absorbers
- Gearbox assembly
- General points
- General points about the vehicle
- Instrument panel
- Instruments and controls
- Lighting - signalling
- Mechanical
- Other
- Power unit
- Pre-heating
- Protections and doors
- Rear axle
- Rear seats
- Rear section
- Rear shock absorbers
- Roof bow
- Roof panel
- Side structure
- Starting
- Steering
- Suspension
- Transmission
- Washing and wiping
Repair manual
Gearbox assembly Peugeot Partner I facelift
Step-by-step instructions on "Gearbox assembly" for Peugeot Partner I facelift (2002–2012). Pick an article — removal, installation, adjustment and diagnostics with illustrations.
Clutch
- Removing - refitting: clutch mechanism
- Removing - refitting: clutch cable
- Help in diagnosis: clutch (technical note)
- Improvement of gear changing on cold starting with all types of manual gearbox
- Aid to mechanical diagnosis: difficult/impossible to change gear (cable operated clutch control)
- Removing - refitting: Accelerator pedal sensor (MOTEUR ELECTRIQUE VENTURI)
- Help in diagnosis: difficult/impossible to change gear (hydraulic clutch control)
Gearbox
- Tightening: differential housing (BE gearbox)
- Presentation: tooling
- Presentation: recommended tools
- Tightening torques: BE4 manual gearbox
- Tightening torques: MA manual gearbox
- Tightening torques: engine/gearbox coupling
- Identification - data: BE4 manual gearbox
- Identification - specification: MA5 manual gearbox
- Checking and adjusting values: MA manual gearbox
- Checking and adjusting values: BE manual gearbox
- Data: gear controls
- Identification - data - tightening torques: gearbox
- Identification - data - tightening torques: gearbox — variant 2
- Check - adjustment: set of primary shaft bearings
- Checks and adjustments: input shaft bearings
- Repair operations: gearbox (increased traction)
- Adjustment: differential housing (increased traction)
- Repair operation: differential box (increased traction)
- Check: Efficiency of the reinforced drive
- Stripping - re-assembling: components internal to the gearbox
- Refitting: manual gearbox
- Dismantling: manual gearbox
- Dismantling: manual gearbox — variant 2
- Refitting: manual gearbox — variant 2
- Removing - refitting: the gear lever acquisition card (MOTEUR ELECTRIQUE VENTURI)
- Removing - refitting: gearbox (DV6ETED M, DV6ATED4, DV6DTED M, DV6B)
- Stripping - re-assembling: input shaft
- Stripping-assembling: secondary shaft with bearing of 17 mm
- Stripping: gearbox
- Removing: input, output shafts and differential
- Stripping - re-assembling: PRIMARY SHAFT
- Stripping - re-assembling: output shaft
- Stripping - re-assembling: synchronizers
- Stripping - re-assembling: gearbox controls
- Stripping - re-assembling: differential
- Stripping - re-assembling: gearbox casing
- Refitting: input, output shafts and differential
- Re-assembling: gearbox
- Refitting: gearbox casing
- Removing: gearbox casing
- Removing: primary and secondary shafts
- Removing: differential box
- Stripping - re-assembling: differential box
- Stripping - re-assembling: clutch housing
- Removing - refitting: gearbox
- Removing - refitting gearbox — variant 2
- Stripping - re-assembling: clutch housing — variant 2
- Refitting: primary and secondary shafts
- Refitting: gearbox casing — variant 2
- Refitting: differential box
- Removing - refitting: gearbox (DV6ATED4)
- Stripping: gearbox — variant 2
- Drain - refill: BE gearbox
- Overhaul: BE4 manual gearbox (Summary)
- Overhaul: manual gearbox - type MA/MAP (Summary)
- Removing: gearbox casing — variant 2
- Overhaul: gearbox on the bench (type be4/5)
- Overhaul: gearbox on the bench
- Cleaning and refitting conditions: gearbox
- Cleaning and refitting conditions: gearbox — variant 2
- Cleaning and refitting conditions: gearbox — variant 3
- Modification: gearbox
- Presentation: special tools (gearbox)
- Tooling: gearbox
- Stripping - re-assembling: components internal to the gearbox — variant 2
- Re-assembling: gearbox — variant 2
- Stripping-assembling: secondary shaft with bearing of 19 mm
- Modification: gearbox — variant 2
- Modifications: gearbox
- Modification: gearbox — variant 3
- Modification: BE4/5 gearbox secondary shaft
- Help in diagnosis: Manual gearbox (technical note)
- Tightening torques: coupling of engine on reduction box (MOTEUR ELECTRIQUE VENTURI)
- Draining - refilling: reduction gear (MOTEUR ELECTRIQUE VENTURI)
- Removing - refitting: motor (MOTEUR ELECTRIQUE VENTURI)
- Removing - refitting: reduction gear driveshaft seals (MOTEUR ELECTRIQUE VENTURI)
- Tightening torques: components of the electric drive train (MOTEUR ELECTRIQUE VENTURI)
- Removing - refitting: electric coolant pump (drive train) (MOTEUR ELECTRIQUE VENTURI)
- Removing - refitting: engine emulation board (MOTEUR ELECTRIQUE VENTURI)
- Removing - refitting: inertial sensor (or inertia sensor) (MOTEUR ELECTRIQUE VENTURI)