Manual sections
Wiring diagrams- Accessories
- Adhesive Foiles
- Air Conditioning
- Airbag
- Antenna
- Battery
- Body Equipment
- Brake Hydraulics, Brake Lines
- Brakes
- Carburettor
- Clutch
- Clutch and Transmission
- Connector pinouts
- Cooling System
- Corrosion Protection
- Diesel Engine
- Distributor Transmission Four Wheel Drive
- Electrical Equipment and Instruments
- Electrical Window Winders
- Engine and Engine Aggregates
- Engine Electrics
- Exhaust System
- Fittings, Hinges, Locks
- Frame
- Front End
- Front Wheel Brake
- Front Wheel Suspension
- Front Wheel Suspension, Wheels and Tyres
- Fuel and Exhaust System
- Fuel Injection Systems
- Fuel System
- Fuse Box
- General Vehicle Information
- Glass, Window Guides, Window Winders
- Headlamps, Lamps and Horn
- Heating, Ventilation
- Heating, Ventilation, Air Conditioning (HVAC)
- Instruments, Telltales
- Maintenance, Body and Chassis Sheet Metal Parts, Frame
- Manual Transmission Four Wheel Drive
- Manual Transmission Rear Wheel Drive
- OHC Petrol Engine
- Other Accessories
- Outside Rear View Mirror
- Paint
- Painting Repair Operations
- Painting Repair System
- Power Steering
- Radiator Grille
- Radio
- Rear Axle and Rear Wheel Suspension
- Rear Axle Four Wheel Drive
- Rear Axle Rear Wheel Drive
- Rear Wheel Brake
- Seat Heating Systems
- Seats, Upholstery, Inner Trim Panels
- Secondary Air Injection
- Service Brake, Parking Brake
- Sheet Metal Parts (Bolted)
- Sheet Metal Parts (Cement and Seal)
- Sheet Metal Parts (Welded)
- Sliding Roof
- Steering
- Steering Gear
- Steering Linkage
- Steering Wheel - Steering Column
- Switches, Control Unit, Relays, Ignition Lock
- Trim Panels, Radiator Grille, Spoiler
- Trim Strips, Lettering, Coverings
- Turbo-Charging
- Wheels and Tyres
- Windscreen Wash/wipe System, Heated Screen
- Wiring Harnesses
Repair manual
Carburettor Opel Campo I
Step-by-step instructions on "Carburettor" for Opel Campo I (1992–2011). Pick an article — removal, installation, adjustment and diagnostics with illustrations.
40articles
Articles in this section
40 articles- Introduction
- Diagnosis
- General Safety Measures and Repair Instructions
- F2:tc 13 - o2 Sensor Circuit Open
- F2:tc 14 - Coolant Temperature Voltage Low
- F2:tc 15 - Coolant Temperature Voltage High
- F2:tc 21 - Vacuum Idle Switch/map Sensor Fault
- F2:tc 22 - Decel. Cutoff Valve Voltage Low
- F2:tc 23 - Air/fuel Ratio Valve Voltage Low
- F2:tc 25 - Sec. Air Injection Valve Voltage Low
- F2:tc 26 - Tank Vent Valve Voltage Low
- F2:tc 27 - Tank Vent Valve Voltage High
- F2:tc 31 - Incorrect RPM Signal
- F2:tc 35 - MAP Valve Voltage High
- F2:tc 36 - MAP Valve Voltage Low
- F2:tc 44 - Exhaust Lean
- F2:tc 45 - Exhaust Rich
- F2:tc 51 - Schubab. Ventil Voltage High
- F2:tc 52 - Replace ECU
- F2:tc 53 - Sec. Air Injection Valve Voltage High
- F2:tc 54 - Air/fuel Ratio Valve Voltage High
- F2:tc 63 - No Vehicle Speed Signal
- F0:test Step 01 - Prom ID
- F0:test Step 02 - Calibration
- F0:test Step 03 - Vacuum Idle Switch
- F0:test Step 04 - MAP Sensor
- F0:test Step 05 - Coolant Temperature
- F0:test Step 06 - Engine Speed
- F0:test Step 07 - Sec. Air Inj. Valve
- F0:test Step 08 - Decel. Cutoff Valve
- F0:test Step 09 - Mix. Valve Pulse Ratio
- F0:test Step 10 - o2 Sensor Circuit
- F0:test Step 11 - o2 Sensor
- F0:test Step 12 - o2 Signal Change
- Circuit Diagram - 2.3L (4ZD1) Engine
- Mixture Control Solenoid
- Fuel Cut Solenoid
- Electronic Control Module (ECM)
- Manifold Absolute Pressure (MAP) Sensor)
- Evaporative Emission Control (Eec) System