Home ReviewsRefund Car not listed?
Home/Nissan/Versa/Nissan Versa I (2006-2012)/Repair manual/Body, Lock & Security System/Door Switch Check (Hatchback)
Contents Wiring diagrams Section: Body, Lock & Security System All sections

Door Switch Check (Hatchback) Nissan Versa I

Body, Lock & Security System ~505 words

Door Switch Check (Hatchback)

  1. CHECK DOOR SWITCHES INPUT SIGNAL With CONSULT-III Check door switches ("DOOR SW-DR", "DOOR SW-AS", "DOOR SW-RL", "DOOR SW-RR", "BACK DOOR SW") in DATA MONITOR mode with CONSULT-III. Refer to , " «CONSULT-III FUNCTION (BCM)»(ref-319465-S24022317362009062600000) ". When doors are open: DOOR SW-DR : ON DOOR SW-AS : ON DOOR SW-RL : ON DOOR SW-RR : ON BACK DOOR SW : ON When doors are closed: DOOR SW-DR : OFF DOOR SW-AS : OFF DOOR SW-RL : OFF DOOR SW-RR : OFF BACK DOOR SW : OFF Without CONSULT-III Check voltage between BCM connector M18 or M19 terminals 12, 13, 43, 47, 48 and ground. TERMINALS VOLTAGE REFERENCE Connector Item Terminals Condition Voltage (V) (Approx). (+) (-) M18 Front door switch RH 12 Ground Open ↓ Closed 0 ↓ Battery voltage Rear door switch RH 13 M19 Back door switch 43 Front door switch LH 47 Rear door switch LH 48 OK or NG OK : Door switch circuit is OK. NG : GO TO 2.
  2. CHECK DOOR SWITCH CIRCUIT Turn ignition switch OFF. Disconnect door switch and BCM. Check continuity between door switch connector (B) B8 (front LH), B108 (front RH) terminal 2 or (C) B6 (rear LH), B116 (rear RH) terminal 1 or back door lock assembly connector (D) D405 terminal 3 and BCM connectors (A) M18, M19 terminals 12, 13, 43, 47 and 48. 1 - 13 : Continuity should exist. 1 - 48 : Continuity should exist. 2 - 12 : Continuity should exist. 2 - 47 : Continuity should exist. 3 - 43 : Continuity should exist. Check continuity between door switch connector (B) B8 (front LH), B108 (front RH) terminal 2 or (C) B6 (rear LH), B116 (rear RH) terminal 1 or back door lock assembly connector (D) D405 terminal 3 and ground. 1 - Ground : Continuity should not exist. 2 - Ground : Continuity should not exist. 3 - Ground : Continuity should not exist. OK or NG OK : GO TO 3. NG : Repair or replace harness.
  3. CHECK DOOR SWITCHES FRONT AND REAR DOORS Check continuity between front door switch terminal 2 or rear door switch terminal 1 and exposed metal of switch while pressing and releasing switch. Door switch is released : Continuity should exist. Door switch is pushed : Continuity should not exist. BACK DOOR Check continuity between back door lock assembly connector (back door switch) terminals 3 and 4 while pressing (closing back door) and releasing (opening back door) switch. When back door is open : Continuity should exist. When back door is closed : Continuity should not exist. OK or NG OK : (Front and rear doors) Switch circuit is OK. OK : (Back door) GO TO 4. NG : Replace door switch.
  4. CHECK BACK DOOR SWITCH GROUND Check continuity between back door lock assembly connector D405 terminal 4 and ground. 4 - Ground : Continuity should exist. OK or NG OK : Back door switch circuit is OK. NG : Repair or replace harness.