Home/Mitsubishi/Lancer Ralliart/Mitsubishi Lancer Ralliart X (2008-2011)/Repair manual/General/FUEL USAGE STATEMENT

Contents

Section: General

MAINTENANCE, REPAIR AND SERVICING EXPLANATIONS

ON-VEHICLE SERVICE

SERVICE PROCEDURES

STANDARD VALUE

LIMIT

REFERENCE VALUE

DANGER, WARNING, AND CAUTION

TIGHTENING TORQUE INDICATION

SPECIAL TOOL NOTE

ABBREVIATIONS

VERIFY THE COMPLAINT

DETERMINE POSSIBLE CAUSES

FIND THE PROBLEM

REPAIR THE PROBLEM

VERIFY THE REPAIR

TROUBLESHOOTING CONTENTS

1. STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING

2. SYSTEM OPERATION AND SYMPTOM VERIFICATION TESTS

3. DIAGNOSTIC FUNCTION

4. DIAGNOSTIC TROUBLE CODE CHART

5. SYMPTOM CHART

6. DIAGNOSTIC TROUBLE CODE PROCEDURES

7. SYMPTOM PROCEDURES

8. SERVICE DATA REFERENCE TABLE

9. CHECK AT ECU TERMINALS

TERMINAL VOLTAGE CHECKS

TERMINAL RESISTANCE AND CONTINUITY CHECKS

10. INSPECTION PROCEDURES USING AN OSCILLOSCOPE

HOW TO USE THE INSPECTION PROCEDURES

HARNESS INSPECTION

MEASURES TO TAKE AFTER REPLACING THE ECU

CONNECTOR MEASUREMENT SERVICE POINTS

IF INSPECTING WITH THE CONNECTOR CONNECTED

CONNECTOR PIN INSPECTION

CONNECTOR ENGAGEMENT INSPECTION

HOW TO COPE WITH INTERMITTENT MALFUNCTIONS

1. ASK THE CUSTOMER ABOUT THE MALFUNCTION

2. DETERMINE THE CONDITIONS FROM THE CUSTOMER'S RESPONSES

3. USE SIMULATION TEST

4. VERIFY THE INTERMITTENT MALFUNCTION IS ELIMINATED

SIMULATION TESTS

HOW TO TREAT PAST TROUBLE

INSPECTION SERVICE POINTS FOR A BLOWN FUSE

VEHICLES IDENTIFICATION NUMBER LOCATION

CODE CHART

VEHICLES FOR USA

VEHICLES FOR PUERTO RICO, GUAM AND SAIPAN

VEHICLES FOR CANADA

CHASSIS NUMBER

CHASSIS NUMBER CODE CHART

VEHICLE IDENTIFICATION CODE PLATE

VEHICLE SAFETY CERTIFICATION LABEL

NATIONAL SAFETY MARK

TIRE AND LOADING INFORMATION PLACARD

ENGINE MODEL STAMPING

THEFT PROTECTION LABEL

2.0L ENGINE

2.4L ENGINE

CAUTIONS FOR WORKING IN ENGINE COMPARTMENT <2.0 L ENGINE Turbo>

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

HOW TO PERFORM VEHICLE IDENTIFICATION NUMBER (VIN) WRITING

WRITING PROCEDURE

VIN WRITING STEPS FOR WCM AND KOS-ECU

INITIALIZATION PROCEDURE FOR LEARNING VALUE IN MFI ENGINE

INITIALIZATION PROCEDURE

PURPOSE

LEARNING PROCEDURE

INITIALIZATION PROCEDURE FOR THROTTLE ACTUATOR CONTROL MOTOR

TIMING CHAIN MAINTENANCE <2.0 L ENGINE Turbo>

LEARNED VALUE READ & SAVE AND WRITE LEARNED VALUE (CHANGED ECU)

LEARNED VALUE RESET

TEST/LIMIT VALUE READOUT

SERVICING ELECTRICAL SYSTEM

APPLICATION OF ANTI-CORROSION AGENTS AND UNDERCOATS

SCAN TOOL (MULTI USE TESTER {M.U.T.-III} SUB ASSEMBLY)

BOLTS AND NUTS WITH STABILIZER FOR COEFFICIENT OF FRICTION

CODING LIST

VARIANT CODING

ENGINE CONTROL MODULE CODING DATA LIST

TC-SST-ECU CODING DATA LIST

ETACS-ECU CODING DATA LIST

OPTION CODING

WRECKER TOWING RECOMMENDATION

FRONT TOWING PICKUP

TOWING WHEN KEYS ARE NOT AVAILABLE

SAFETY PRECAUTIONS

POST TYPE

TIGHTENING TORQUE

STANDARD BOLT AND NUT TIGHTENING TORQUE

FLANGE BOLT AND NUT TIGHTENING TORQUE

LUBRICATION AND MAINTENANCE

MAINTENANCE SCHEDULES

SEVERE SERVICE

ENGINE OIL

LUBRICANTS AND GREASES

FUEL USAGE STATEMENT

GASOLINE CONTAINING ALCOHOL

GASOLINE CONTAINING METHYL TERTIARY BUTYL ETHER (MTBE)

MATERIALS ADDED TO FUEL

RECOMMENDED LUBRICANTS

LUBRICANT CAPACITY TABLE

OIL VISCOSITY <2.0L NON-TURBO ENGINE, 2.4L ENGINE>

COOLANT

SCHEDULED MAINTENANCE SERVICE FOR EMISSION CONTROL AND PROPER VEHICLE PERFORMANCE

SCHEDULED MAINTENANCE UNDER SEVERE USAGE CONDITIONS

1. FUEL SYSTEM (TANK, PIPE LINE AND CONNECTION, AND FUEL TANK FILLER TUBE CAP) (CHECK FOR LEAKS)

2. FUEL HOSES (CHECK CONDITION)

3. AIR CLEANER ELEMENT (REPLACE)

4. EVAPORATIVE EMISSION CONTROL SYSTEM (EXCEPT EVAPORATIVE EMISSION CANISTER) (CHECK FOR LEAKS AND CLOGGING)

5. SPARK PLUGS (REPLACE)

6. INTAKE AND EXHAUST VALVE CLEARANCE (INSPECT AND ADJUST)

8. EXHAUST SYSTEM (CONNECTIONS PORTION OF MUFFLER, MUFFLER PIPES AND CONVERTER HEAT SHIELDS) (CHECK AND SERVICE)

10. ENGINE OIL FILTER (REPLACE)

Engine Oil Filter Selection

TRANSMISSION FLUID CHECK

13. ENGINE COOLANT (CHANGE)

Change Coolant

14. COOLANT HOSES (RADIATOR HOSE, HEATER HOSE) (INSPECT)

DISK BRAKE ROTOR CHECK

BRAKE LINING THICKNESS CHECK

17. BRAKE HOSES (CHECK FOR DETERIORATION OR LEAKS)

20. SUSPENSION SYSTEM (INSPECT FOR LOOSENESS AND DAMAGE)

21. TIRES (ROTATE)

7. DRIVE BELT (FOR THE GENERATOR AND POWER STEERING OIL PUMP) (REPLACE)

TC-SST OIL LEVEL CHECK

TRANSFER OIL CHANGE

FLUID LEVEL CHECK

15. COOLANT HOSES (RADIATOR HOSE, HEATER HOSE) (INSPECT)

DISK BRAKE PAD CHECK

BRAKE DISC THICKNESS CHECK

18. BALL JOINT AND STEERING LINKAGE SEALS (INSPECT FOR GREASE LEAKS AND DAMAGE)

19. DRIVE SHAFT BOOTS (INSPECT FOR GREASE LEAKS AND DAMAGE)

21. REAR AXLE OIL (WITH LSD) (CHANGE)

22. TIRES (ROTATE)

MAIN SEALANT AND ADHESIVE TABLE

All sections

FUEL USAGE STATEMENT Mitsubishi Lancer Ralliart X

General

FUEL USAGE STATEMENT

CAUTION

Using leaded gasoline in this car will damage the catalytic converters and heated oxygen sensors, and affect the warranty coverage validity.

This vehicle must use unleaded gasoline only.

This vehicle has a fuel filler tube which is especially designed to accept only the smaller-diameter unleaded gasoline dispensing nozzle.