Manual sections
Repair manual

Controller Area Network (CAN) Mitsubishi Lancer Ralliart X

Step-by-step instructions on "Controller Area Network (CAN)" for Mitsubishi Lancer Ralliart X (2008–2011). Pick an article — removal, installation, adjustment and diagnostics with illustrations.

45subsections
45articles
253illustrations

GENERAL INFORMATION

1 article

CAN-B

1 article

CAN-C

1 article

DIAGNOSIS CAN-C

1 article

SPECIAL TOOLS

1 article

TEST EQUIPMENT

1 article

SERVICE PRECAUTIONS

1 article

PRECAUTIONS ON HOW TO REPAIR THE TERMINATOR RESISTOR

1 article

EXPLANATION ABOUT THE SCAN TOOL (M.U.T.-III) CAN BUS DIAGNOSTICS

1 article

ON-BOARD DIAGNOSTICS

1 article

HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)

1 article

HOW TO DIAGNOSE THE CAN BUS LINE

1 article

CAN BUS DIAGNOSTICS TABLE

1 article

DIAGNOSTIC ITEM 1: Diagnose when the scan tool cannot receive the data sent by ETACS-ECU

1 article

FUNCTION

1 article

TROUBLE JUDGEMENT CONDITIONS

1 article

TROUBLESHOOTING HINTS

1 article

DIAGNOSIS

1 article

DIAGNOSTIC ITEM 2: Malfunction of the ETACS-ECU

1 article

TROUBLESHOOTING HINT

1 article

DIAGNOSTIC ITEM 3: Abnormal short between the CAN-C bus lines

1 article

DIAGNOSTIC ITEM 6: Diagnose when the scan tool cannot receive the data sent by steering wheel sensor.

1 article

DIAGNOSTIC ITEM 7: Diagnose when the scan tool cannot receive the data sent by AWC-ECU.

1 article

DIAGNOSTIC ITEM 8: Diagnose when the scan tool cannot receive the data sent by ABS-ECU < vehicles with ABS (Except vehicles with ASC)> or ASC-ECU

1 article

DIAGNOSTIC ITEM 9: Diagnose when the scan tool cannot receive the data sent by shift lever. )

1 article

DIAGNOSTIC ITEM 10: Diagnose when the scan tool cannot receive the data sent by TCM.

1 article

DIAGNOSTIC ITEM 11: Diagnose when the scan tool cannot receive the data sent by transaxle assembly (TC-SST-ECU).

1 article

DIAGNOSTIC ITEM 12: Diagnose when the scan tool cannot receive the data sent by ECM

1 article

DIAGNOSTIC ITEM 13: Diagnose the lines between the ETACS-ECU and joint connector (CAN2)

1 article

DIAGNOSTIC ITEM 14: Diagnose the lines between joint connector (CAN2) and joint connector (CAN3)

1 article

DIAGNOSTIC ITEM 15: Diagnose the lines between joint connector (CAN3) and joint connector (CAN4).

1 article

DIAGNOSTIC ITEM 16: Diagnose when the scan tool cannot receive the data sent by KOS-ECU.

1 article

DIAGNOSTIC ITEM 17: Diagnose when the scan tool cannot receive the data sent by WCM.

1 article

DIAGNOSTIC ITEM 18: Diagnose when the scan tool cannot receive the data sent by SRS-ECU

1 article

DIAGNOSTIC ITEM 19: Diagnose when the scan tool cannot receive the data sent by A/C-ECU or heater control unit < vehicles without A/C >

1 article

DIAGNOSTIC ITEM 20: Diagnose when the scan tool cannot receive the data sent by radio and CD player.

1 article

DIAGNOSTIC ITEM 21: Diagnose when the scan tool cannot receive the data sent by CAN box unit

1 article

DIAGNOSTIC ITEM 22: Diagnose when the scan tool cannot receive the data sent by hands free module.

1 article

DIAGNOSTIC ITEM 23: Diagnose when the scan tool cannot receive the data sent by combination meter

1 article

DIAGNOSTIC ITEM 24: Diagnose when the scan tool cannot receive the data sent by occupant classification-ECU

1 article

DIAGNOSTIC ITEM 25: Diagnose when the scan tool cannot receive the data sent by satellite radio tuner

1 article

DIAGNOSTIC ITEM 26: Short to power supply or ground in both CAN_H and CAN_L lines

1 article

DIAGNOSTIC ITEM 27: Diagnose the ETACS-ECU, joint connector (CAN1) or lines between ETACS-ECU and joint connector (CAN1)

1 article

DIAGNOSTIC ITEM 28: Short to power supply or ground, open circuit or line-to-line short in the CAN-B bus lines

1 article