Home/Mitsubishi/Lancer Evolution/Mitsubishi Lancer Evolution X (2007-2016)/Repair manual/Engine Mechanical <2.4l> - Except Lancer Evolution/>> E << WATER PUMP PULLEY INSTALLATION

Contents

Section: Engine Mechanical <2.4l> - Except Lancer Evolution

GENERAL INFORMATION

ENGINE DIAGNOSIS

SERVICE SPECIFICATIONS

SEALANTS AND ADHESIVE

SPECIAL TOOLS

OPERATION CHECK

FUNCTION CHECK

VALVE CLEARANCE CHECK AND ADJUSTMENT

IGNITION TIMING CHECK

CURB IDLE SPEED CHECK

IDLE MIXTURE CHECK

COMPRESSION PRESSURE CHECK

MANIFOLD VACUUM CHECK

<< A >> RADIATOR CONDENSER TANK ASSEMBLY REMOVAL

<< B >> DRIVE BELT REMOVAL

<< A >> ROCKER COVER ASSEMBLY REMOVAL

<< B >> NUMBER 1 CYLINDER COMPRESSION TOP DEAD CENTER SETTING

<< D >> FRONT CAMSHAFT BEARING CAP REMOVAL

<< E >> OIL FEEDING CAMSHAFT BEARING CAP/CAMSHAFT BEARING CAP/THRUST CAMSHAFT BEARING CAP REMOVAL

<< G >> CAMSHAFT SPROCKET/CAMSHAFT REMOVAL

<< H >> POWER STEERING OIL PUMP ASSEMBLY REMOVAL

<< I >> OIL FEEDER CONTROL VALVE REMOVAL

>> A << O-RING/OIL FEEDER CONTROL VALVE INSTALLATION

>> E << CAMSHAFT BEARING/CAMSHAFT AND CAMSHAFT SPROCKET ASSEMBLY (EXHAUST SIDE) INSTALLATION

>> F << FRONT CAMSHAFT BEARING CAP INSTALLATION

REMOVAL AND INSTALLATION

<< B >> OIL FEEDING CAMSHAFT BEARING CAP/CAMSHAFT BEARING CAP/THRUST CAMSHAFT BEARING CAP REMOVAL

<< C >> VALVE TAPPET REMOVAL

<< E >> VALVE STEM SEAL REMOVAL

>> A << VALVE STEM SEAL INSTALLATION

>> B << VALVE SPRING RETAINER LOCK INSTALLATION

>> C << VALVE TAPPET INSTALLATION

>> D << THRUST CAMSHAFT BEARING CAP/CAMSHAFT BEARING CAP/OIL FEEDING CAMSHAFT BEARING CAP INSTALLATION

<< A >> A/C COMPRESSOR AND CLUTCH ASSEMBLY REMOVAL

>> B << ENGINE OIL PAN DRAIN PLUG GASKET INSTALLATION

>> C << A/C COMPRESSOR AND CLUTCH ASSEMBLY INSTALLATION

INSPECTION

<< A >> FLYWHEEL BOLT /DRIVE PLATE BOLT REMOVAL

<< A >> RADIATOR UPPER HOSE/RADIATOR LOWER HOSE DISCONNECTION

<< C >> FRONT CAMSHAFT BEARING CAP REMOVAL

<< D >> OIL FEEDING CAMSHAFT BEARING CAP/CAMSHAFT BEARING CAP/THRUST CAMSHAFT BEARING CAP REMOVAL

<< E >> CYLINDER HEAD BOLT/CYLINDER HEAD BOLT ASSEMBLY REMOVAL

>> A << CYLINDER HEAD GASKET/CYLINDER HEAD ASSEMBLY INSTALLATION

>> C << CAMSHAFT BEARING/CAMSHAFT AND CAMSHAFT SPROCKET ASSEMBLY INSTALLATION

>> E << FRONT CAMSHAFT BEARING CAP INSTALLATION

>> F << FUEL HIGH-PRESSURE HOSE CONNECTION

>> G << O-RING INSTALLATION

<< A >> CRANKSHAFT PULLEY REMOVAL

<< B >> POWER STEERING OIL PUMP ASSEMBLY REMOVAL

<< C >> ENGINE AND TRANSAXLE ASSEMBLY HOLDING

<< D >> TIMING CHAIN CASE ASSEMBLY REMOVAL

>> C << CRANKSHAFT FRONT OIL SEAL INSTALLATION

>> D << TIMING CHAIN CASE ASSEMBLY INSTALLATION

>> E << WATER PUMP PULLEY INSTALLATION

<< A >> TIMING CHAIN TENSIONER REMOVAL

>> B << TIMING CHAIN TENSIONER INSTALLATION

<< A >> BALANCER SHAFT AND OIL PUMP MODULE REMOVAL

<< B >> FUEL HIGH-PRESSURE HOSE DISCONNECTION

<< C >> POWER STEERING OIL PUMP ASSEMBLY REMOVAL

<< D >> A/C COMPRESSOR AND CLUTCH ASSEMBLY REMOVAL

<< F >> ENGINE MOUNTING INSULATOR REMOVAL

>> A << ENGINE ASSEMBLY INSTALLATION

>> B << ENGINE MOUNTING INSULATOR INSTALLATION

>> D << FUEL HIGH-PRESSURE HOSE CONNECTION

>> E << RADIATOR LOWER HOSE/RADIATOR UPPER HOSE CONNECTION

All sections

>> E << WATER PUMP PULLEY INSTALLATION Mitsubishi Lancer Evolution X

Engine Mechanical <2.4l> - Except Lancer Evolution 1 illustration

>> E << WATER PUMP PULLEY INSTALLATION

Temporarily tighten the water pump pulley mounting bolts. Then, tighten them to the specified torque after the installation of drive belt.

Tightening torque: 9.0 ± 1.0 N.m (80 ± 9 in-lb)

Scheme 330

Scheme 330: REMOVAL AND INSTALLATION

Scheme 330: REMOVAL AND INSTALLATION

Required Special Tool

MB991614: Angle Gauge