11 31 Camshaft N14
| Diameters of bearings | Mm | 23.979... 23.995 |
|---|
| Radial runout | Mm | 0.037... 0.073 |
| Wear limit: Radial runout | Mm | 0.10 |
| Axial play | Mm | 0.040... 0.090 |
| Wear limit: Axial play | Mm | 0.25 |
11 24 Connecting Rods and Bearings N14
| Conrod bushing: Inside diameter | Mm | 20.007... 20.020 |
|---|
| Running clearance between small-end bushing and piston pin | Mm | 0.014... 0.025 |
| Wear limit | Mm | 0.05 |
CONNECTING RODS AND BEARINGS SPECIFICATION
11 21 Crankshaft and Bearings N14
| Diameters of main journals | Mm | 44.981... 45.000 |
|---|
| Radial play of main bearings | Mm | 0.026... 0.043 |
| Radial play of main bearings (wear limit) | Mm | 0.070 |
| Axial play of crankshaft | Mm | 0.015... 0.050 |
| Axial play of crankshaft (wear limit) | Mm | 0, 30 |
CRANKSHAFT AND BEARINGS SPECIFICATION
11 21 Conrod Bearings N14
| Diameters of conrod bearing journals | Mm | 40.975... 40.991 |
|---|
| Radial play of conrod bearings | Mm | 0.022... 0.066 |
| Radial play of conrod bearings (wear limit) | Mm | 0, 080 |
CRANKSHAFT AND BEARINGS SPECIFICATION
11 12 Cylinder Head with Cover N14
| The cylinder head sealing face must not be remachined | | |
|---|
| Inside diameter of installed valve guide | Mm | 5.000... 5.012 |
| Running clearance between valve and valve guide | | |
| Intake | Mm | 0.025... 0.047 |
| Exhaust | Mm | 0.033... 0.060 |
| Maximum running clearance between valve and valve guide | | |
| Wear limit: Intake | Mm | 0.08 |
| Wear limit: Exhaust | Mm | 0.10 |
CYLINDER HEAD WITH COVER SPECIFICATION
11 12 Cylinder Head with Valve Seat Cover N14
| Valve seat angle | ° | 45 |
|---|
| Correction angle: outer | ° | 15 |
| Correction angle, inlet: inner | ° | 60 |
| Correction angle, exhaust: inner | ° | 75 |
| Valve seat width: Intake | Mm | 1.0... 1.2 |
| Valve seat width: Exhaust | Mm | 1.2... 1.6 |
| Valve seat | | |
| Valve seat surface: Outside dia. inlet | Mm | 28.8 ± 0.2 |
| Valve seat surface: Outside dia. exhaust | Mm | 26, 2 ± 0, 2 |
CYLINDER HEAD WITH VALVE SEAT COVER SPECIFICATION
11 11 Engine Block, Cylinder Crankcase N14
| Bore dia. (1) | Mm | 77.000... 77.014 |
|---|
| Permitted out-of-round of cylinder bore (1) | Mm | 0.005 |
| Permitted conicity of cylinder bore (1) | Mm | 0.01 |
| Permissible total wear tolerance between piston and cylinder (engine operated) | Mm | 0.10 |
| (1) new condition |
ENGINE BLOCK, CYLINDER CRANKCASE SPECIFICATION
11 00 Engine in general N14
| Cylinder | | 4 |
|---|
| Bore | Mm | 73, 0 |
| Stroke | Mm | 85, 8 |
| Effective displacement | Cm 3 | 1598 |
| Compression ratio | 1 | 10.5 |
| Idle speed | RPM | 720... 820 |
| Rated speed | RPM | 4000 |
| Max. permissible engine speed | RPM | 6500 |
| Compression pressure | Bar | 8...12 |
| Compression pressure (maximum difference between cylinders) | Bar | 3 |
ENGINE IN GENERAL SPECIFICATION
11 41 Oil Pump with Strainer and Drive N14
| Oil pressure at idle (engine at normal operating temperature) | Min bar | 0.7 |
|---|
| Control pressure at 3000 RPM (engine at normal operating temperature) | Bar | 1.7...3.0 |
OIL PUMP WITH STRAINER AND DRIVE SPECIFICATION
11 25 Pistons with Rings and Pins N14
| 1st groove | | |
|---|
| End clearance | Mm | 0.25... 0.35 |
| Contact clearance (wear limit) | Mm | 0.91 |
| Axial play | Mm | 0.030... 0.070 |
| 2nd groove | | |
| End clearance | Mm | 0.35... 0.50 |
| Contact clearance (wear limit) | Mm | 1.06 |
| Axial play | Mm | 0.030... 0.070 |
| 3rd groove | | |
| End clearance | Mm | 0.10... 0.35 |
| Contact clearance (wear limit) | Mm | 0.82 |
| Axial play | Mm | 0.030... 0.070 |
PISTONS WITH RINGS AND PINS SPECIFICATION
| Piston and pin are paired to each other - replace together only. | | |
|---|
| Measuring point "A" (position) | Mm | 10 |
| Piston diameter at measuring point "A" | | |
| Original (new dimension) | Mm | 76.941... 76.959 |
| Piston running clearance | Mm | 0.041... 0.064 |
| Permissible total wear tolerance between piston and cylinder (engine operated) | Mm | 0.10 |
PISTONS WITH RINGS AND PINS SPECIFICATION
11 34 Valves with Springs N14
| Valve clearance at max. 35°C coolant temperature | | |
|---|
| Stem | | |
| Intake | Mm | 4.9605... 4.9755 |
| Exhaust | Mm | 4.9525... 4.9675 |
VALVES WITH SPRINGS SPECIFICATION
