Home ReviewsRefund
Home/Mercury/Sable/Mercury Sable V (2007-2009)/Repair manual/Communication Devices/Module Configuration System: Diagnosis
Contents Wiring diagrams Section: Communication Devices All sections

Module Configuration System: Diagnosis Mercury Sable V

Communication Devices ~590 words

Inspection and Verification

This article provides step-by-step module configuration procedures. Carry out the PMI procedures in this article when another workshop manual article directs to carry out "configuration" or when DTCs from the list below are present

DTCDescriptionSourceAction
B2477Module Configuration FailureABS module Accessory protocol interface module (APIM) Audio control module (ACM) Driver seat module (DSM) Instrument cluster (IC) Rear entertainment module (RETM) Parking aid module (PAM) Restraints control module (RCM) Satellite digital audio receiver system (SDARS) module Smart junction box (SJB) Steering effort control module (SECM)CARRY OUT programmable module installation (PMI). REFER to Programmable Module Installation .
B2900VIN MismatchABS module RCM 4X4 control moduleCARRY OUT PMI. REFER to Programmable Module Installation .
B2A21One or More Configuration Files Missing/CorruptSJBCARRY OUT PMI. REFER to Programmable Module Installation .
P0602Powertrain Control Module Programming ErrorPCMCARRY OUT PMI. REFER to Programmable Module Installation .
P0605Internal Control Module Read Only Memory (ROM) ErrorPCMCARRY OUT PMI. REFER to Programmable Module Installation .
P1639Vehicle ID Block Corrupted, Not ProgrammedPCMCARRY OUT PMI. REFER to Programmable Module Installation .
U0300Internal Control Module Software IncompatibilityPCM HVAC moduleCARRY OUT PMI. REFER to Programmable Module Installation .
U0301Software Incompatibility with Engine/Powertrain Control ModulePCMCARRY OUT PMI. REFER to Programmable Module Installation .
U2050No Application PresentABS module ACM APIM DSM HVAC module IC LTM Occupant classification system module (OCSM) PCM RETM RCM SDARS module SECM SJB 4X4 control moduleCARRY OUT PMI. REFER to Programmable Module Installation .
U2051One or More Calibration Files Missing / CorruptACM HVAC module LTM OCSM PCM 4X4 control moduleCARRY OUT PMI. REFER to Programmable Module Installation .

DIAGNOSTIC TROUBLE CODE (DTC) CHART

Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is Available

Note. Following module installation, some modules require a separate learning procedure be carried out. For adaptive learning and calibration instructions, refer to the specific module removal and installation procedures.

  1. Connect the IDS and identify the vehicle as normal.
  2. From the Toolbox icon, select Module Programming and press the check mark.
  3. Select Programmable Module Installation.
  4. Select the module that is being replaced.
  5. Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
  6. Install the new module and press the check mark.
  7. Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
  8. The IDS downloads the data into the new module and displays Module Configuration Complete.
  9. Test module for correct operation.

Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is NOT Available

Note. Following module installation, some modules require a separate learning procedure be carried out. For adaptive learning and calibration instructions, refer to the specific module removal and installation procedures.

  1. Install the new module.
  2. Connect the IDS and identify the vehicle as normal.
  3. From the Toolbox icon, select Module Programming and press the check mark.
  4. Select Programmable Module Installation.
  5. Select the module that was replaced.
  6. Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
  7. Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
  8. If the data is not available, the IDS displays a screen stating to contact the As-Built Data Center. Retrieve the data from the technician service publication website at this time and press the check mark.
  9. Enter the module data and press the check mark.
  10. The IDS downloads the data into the new module and displays Module Configuration Complete.
  11. Test module for correct operation.

Accessory Protocol Interface Module (APIM) Programming Using the Integrated Diagnostic System (IDS)

Note. If a new accessory protocol interface module (APIM) is being installed, install the new APIM before carrying out the following procedure. For additional information, refer to INFORMATION AND ENTERTAINMENT SYSTEMS article.

  1. Turn the audio control module (ACM) on.
  2. Connect the scan tool to the data link connector (DLC).
  3. Connect one end of the universal serial bus (USB) male-A to male-A cable to the scan tool.
  4. Connect the other end of the USB male-A to male-A cable to the vehicle USB port.
  5. From the technician service publication website, run OASIS using Quick Start or by manually entering the vehicle identification number (VIN).
  6. From the OASIS tab, select the "Sync/APIM" bullet.
  7. Select the "Read APIM" button to verify the current APIM vehicle interface processor (VIP) and consumer interface processor (CIP) software levels.
  8. Select the desired software level from the list of available software for programming then select the "Program APIM" button to begin the APIM programming process. Enter the APIM As-Built data if prompted. When only the CIP is being programmed, select cancel when prompted whether or not to program the VIP. When the VIP is programmed, the CIP will be programmed automatically.
  9. The Sync/APIM application downloads the software into the APIM and displays "Programming has been completed successfully".
  10. Test the audio system for correct operation.

More articles — Module Configuration System