DTC TABLE (PJB)[CONTROL SYSTEM]
| DTC No. | Description | Detection condition | Page |
|---|---|---|---|
| B1014 | Rain sensor error (1) | Rain sensor internal malfunction | (See DTC B1014 [CONTROL SYSTEM] ). |
| B1217 | Alarm activation horn circuit failure | Short to GND or power supply in wiring harness between PJB and horn relay | (See DTC B1217 [CONTROL SYSTEM] ). |
| B1311 | Unlock switch circuit open | Open circuit in wiring harness between PJB and driver-side door lock-link switch (unlock signal) | (See DTC B1311 [CONTROL SYSTEM] ). |
| B1317 | Battery voltage high | Input voltage from the battery is excessively high | (See DTC B1317 [CONTROL SYSTEM] ). |
| B1318 | Battery voltage low | Input voltage from the battery is excessively low | (See DTC B1318 [CONTROL SYSTEM] ). |
| B1320 | Door ajar LF circuit open | Open circuit in wiring harness between PJB and front door latch switch (driver-side) | (See DTC B1320 [CONTROL SYSTEM] ). |
| B1328 | Door ajar RF circuit open | Open circuit in wiring harness between PJB and front door latch switch (passenger-side) | (See DTC B1328 [CONTROL SYSTEM] ). |
| B1336 | Door ajar RR circuit open | Open circuit in wiring harness between PJB and rear door latch switch (RH) | (See DTC B1336 [CONTROL SYSTEM] ). |
| B1342 | ECU is faulted | PJB microcomputer malfunction | (See DTC B1342 [CONTROL SYSTEM] ). |
| B1345 | Heated backlite input circuit short to ground | Short to GND in wiring harness between PJB and climate control unit (rear window defroster switch) | (See DTC B1345 [CONTROL SYSTEM] ). |
| B1350 | Heated backlite relay short to ground | Short to GND or power supply in wiring harness between PJB and rear window defroster relay | (See DTC B1350 [CONTROL SYSTEM] ). |
| B1447 | Wiper park sense circuit open | Open circuit in wiring harness between PJB and windshield wiper motor (autostop switch) | (See DTC B1447 [CONTROL SYSTEM] ). |
| B1472 | Headlight on status switch input circuit short to ground | Short to GND in wiring harness between PJB and light switch (low beam) | (See DTC B1472 [CONTROL SYSTEM] ). |
| B1502 | Light turn signal left circuit short to ground | Short to GND in wiring harness between PJB and turn lights | (See DTC B1502 [CONTROL SYSTEM] ). |
| B1506 | Light turn signal right circuit short to ground | Short to GND in wiring harness between PJB and turn switch | (See DTC B1506 [CONTROL SYSTEM] ). |
| B1520 | Hood switch circuit open | Open circuit in wiring harness between PJB and hood latch switch | (See DTC B1520 [CONTROL SYSTEM] ). |
| B1570 | Headlight high beam status input circuit short to battery | Short to power supply in wiring harness between PJB and light switch (high beam) | (See DTC B1570 [CONTROL SYSTEM] ). |
| B1572 | Door ajar LR circuit open | Open circuit in wiring harness between PJB and rear door latch switch (LH) | (See DTC B1572 [CONTROL SYSTEM] ). |
| B1607 | Key illumination circuit short to battery | Short to power supply in wiring harness between PJB and key illumination | (See DTC B1607 [CONTROL SYSTEM] ). |
| B1614 | Rear wiper interval switch input circuit short to ground | Short to GND in wiring harness between PJB and rear wiper and washer switch (INT) | (See DTC B1614 [CONTROL SYSTEM] ). |
| B1696 | Auto light switch input circuit short to ground (1) f | Short to GND in wiring harness between PJB and light switch (AUTO) | (See DTC B1696 [CONTROL SYSTEM] ). |
| B1798 | Position lights switch (TNS) input circuit short to ground | Short to GND in wiring harness between PJB and light switch (TNS) | (See DTC B1798 [CONTROL SYSTEM] ). |
| B1812 | Backup light switch input circuit short to battery | Short to power supply in wiring harness between PJB and back-up light switch | (See DTC B1812 [CONTROL SYSTEM] ). |
| B1873 | Turn signal/hazard power feed circuit short to ground | Short to GND in wiring harness between PJB and hazard warning switch | (See DTC B1873 [CONTROL SYSTEM] ). |
| B2017 | DRL left output circuit failure | Open circuit or short to GND in wiring harness between PJB and headlight (low beam) | (See DTC B2017 [CONTROL SYSTEM] ). |
| B2018 | DRL right output circuit failure | Open circuit or short to GND in wiring harness between PJB and headlight (low beam) | (See DTC B2018 [CONTROL SYSTEM] ). |
| B2060 | Heated backlite indicator circuit failure | Short to power supply in wiring harness between PJB and climate control unit (rear window defroster indicator) | (See DTC B2060 [CONTROL SYSTEM] ). |
| B2095 | Reset switch circuit failure | Short to GND in wiring harness between PJB and driver-side door key cylinder switch (unlock) | (See DTC B2095 [CONTROL SYSTEM] ). |
| B2096 | Set switch circuit failure | Short to GND in wiring harness between PJB and driver-side door key cylinder switch (lock) | (See DTC B2096 [CONTROL SYSTEM] ). |
| B2114 | Front washer switch input circuit short to battery | Short to power supply in wiring harness between PJB and windshield wiper and washer switch (front washer) | (See DTC B2114 [CONTROL SYSTEM] ). |
| B2175 | A/C request signal circuit short to ground | Short to GND in wiring harness between PJB and climate control unit (A/C ON request) | (See DTC B2175 [CONTROL SYSTEM] ). |
| B2180 | Front wiper switch (slow) circuit short to ground | Short to GND in wiring harness between PJB and windshield wiper and washer switch (low) | (See DTC B2180 [CONTROL SYSTEM] ). |
| B2181 | Front wiper switch (fast) circuit short to ground | Short to GND in wiring harness between PJB and windshield wiper and washer switch (high) | (See DTC B2181 [CONTROL SYSTEM] ). |
| B2212 | Panel light control circuit failure | Input voltage from the panel light control switch is excessively low or high | (See DTC B2212 [CONTROL SYSTEM] ). |
| B2218 | Central locking switch circuit failure | Short to GND in wiring harness between PJB and door lock switch (driver's side and passenger's side) | (See DTC B2218 [CONTROL SYSTEM] ). |
| B2254 | Front fog light switch failure | Short to GND in wiring harness between PJB and fog light switch | (See DTC B2254 [CONTROL SYSTEM] ). |
| B2259 | Front wiper variable intermittent switch circuit failure | Input voltage from the windshield wiper and washer switch (INT volume or sensitivity adjustment volume) is excessively low or high | (See DTC B2259 [CONTROL SYSTEM] ). |
| B2259 | Intermittent wiper circuit failure | Input voltage from the windshield wiper and washer switch (INT) is excessively low or high | (See DTC B2259 [CONTROL SYSTEM] ). |
| B2259 | Intermittent wiper circuit short to ground | Short to GND in wiring harness between PJB and windshield wiper and washer switch (INT) | (See DTC B2259 [CONTROL SYSTEM] ). |
| B2477 | Module configuration failure | PJB data configuration error | (See DTC B2477 [CONTROL SYSTEM] ). |
| B2479 | Park brake switch circuit open | Open circuit in wiring harness between PJB and parking brake switch | (See DTC B2479 [CONTROL SYSTEM] ). |
| B2512 | Front fog relay short to battery | Short to power supply or GND in wiring harness between PJB and front fog light relay | (See DTC B2512 [CONTROL SYSTEM] ). |
| B2555 | Dome light output circuit short to battery | Open circuit or short to power supply in wiring harness between PJB and interior lights | (See DTC B2555 [CONTROL SYSTEM] ). |
| B2559 | Trunk lid lock/unlock switch circuit failure | Short to GND in wiring harness between PJB and trunk lid key cylinder switch | (See DTC B2559 [CONTROL SYSTEM] ). |
| B2574 | Driver door lock switch short to ground | Short to GND in wiring harness between PJB and driver-side door lock-link switch | (See DTC B2574 [CONTROL SYSTEM] ). |
| B2721 | Liftgate/decklid ajar output short to ground | Short to GND in wiring harness between PJB and trunk lid latch switch | (See DTC B2721 [CONTROL SYSTEM] ). |
| B2897 | Auto light relay circuit failure (1) | Short to power supply in PJB internal circuit between microcomputer and headlight LO relay | (See DTC B2897 [CONTROL SYSTEM] ). |
| B2898 | Right turn signal indicator output failure | Open circuit or short to power supply or GND in wiring harness between PJB and turn light Turn light bulb malfunction | (See DTC B2898 [CONTROL SYSTEM] ). |
| B2899 | Left turn signal indicator output failure | Open circuit or short to power supply or GND in wiring harness between PJB and turn light Turn light bulb malfunction | (See DTC B2899 [CONTROL SYSTEM] ). |
| B2966 | Front washer switch stuck | Windshield washer switch stuck ON position | (See DTC B2966 [CONTROL SYSTEM] ). |
| C1189 | Brake fluid level sensor input circuit open | Open circuit in wiring harness between PJB and brake fluid level sensor | (See DTC C1189 [CONTROL SYSTEM] ). |
| U2030 | Rain sensor communication fault (1) | Communication error to rain sensor | (See DTC U2030 [CONTROL SYSTEM] ). |
| (1) If equipped, for Canada only. | |||
| (1) | If equipped, for Canada only. |
DTC CHART
Diagnostic procedure
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT DTC Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the rain sensor, then go to the next step. (See RAIN SENSOR REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 2 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1014 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT HORN RELAY CONNECTOR Turn the ignition switch off. Disconnect the horn relay connector. Inspect the horn relay connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 7. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 7. |
| No | Go to the next step. | ||
| 3 | INSPECT HORN RELAY CONTROL CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between PJB terminal J-04 N (wiring harness-side) and horn relay terminal E (wiring harness-side). Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible short to GND, then go to Step 7. | ||
| 4 | INSPECT HORN RELAY CONTROL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-04 N (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 7. |
| No | Go to the next step. | ||
| 5 | INSPECT HORN RELAY CONTROL CIRCUIT FOR SHORT TO POWER SUPPLY Turn the ignition switch to the ON position (Engine off). Measure the voltage between PJB terminal J-04 N (wiring harness-side) and body GND. Is the voltage B+? | Yes | Repair or replace the wiring harness for a possible short to power supply, then go to Step 7. |
| No | Go to the next step. | ||
| 6 | INSPECT HORN RELAY Inspect the horn relay. (See RELAY INSPECTION .) Is there any malfunction? | Yes | Replace the horn relay, then go to the next step. |
| No | Go to the next step. | ||
| 7 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1217 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (DRIVER-SIDE) CONNECTOR Turn the ignition switch off. Disconnect the front door latch and lock actuator (driver-side) connector. Inspect the front door latch and lock actuator (driver-side) connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (DRIVER-SIDE) SIGNAL CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between PJB terminal J-06 V (wiring harness-side) and front door latch and lock actuator (driver-side) terminal E (wiring harness-side). Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 5. | ||
| 4 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (DRIVER-SIDE) Inspect the front door latch and lock actuator (driver-side). (See FRONT DOOR LATCH AND LOCK ACTUATOR INSPECTION .) Is there any malfunction? | Yes | Replace the front door latch and lock actuator (driver-side), then go to the next step. (See FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1311 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT DTC FROM PCM Connect the M-MDS to the DLC-2. Are any DTCs from the PCM displayed? | Yes | Perform DTC inspection. (See DTC TABLE [LF, L3] .) Go to the next step. |
| No | Go to the next step. | ||
| 2 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Turn the ignition switch to LOCK position then ON position. Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1317 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT DTC FROM PCM Connect the M-MDS to the DLC-2. Are any DTCs from the PCM displayed? | Yes | Perform DTC inspection. (See DTC TABLE [LF, L3] .) Go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT PJB POWER SUPPLY CIRCUIT FOR OPEN CIRCUIT Disconnect the negative battery cable. Disconnect the positive battery cable. Inspect for continuity between following terminals: PJB terminal J-01 F (wiring harness-side) - battery positive terminal (wiring harness-side) PJB terminal J-03 AP (wiring harness-side) - battery positive terminal (wiring harness-side) Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 5. | ||
| 4 | INSPECT PJB POWER SUPPLY CIRCUIT FOR SHORT TO GND Inspect for continuity between following terminals: PJB terminal J-01 F (wiring harness-side) - body GND PJB terminal J-03 AP (wiring harness-side) - body GND Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to the next step. |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Turn the ignition switch to LOCK position then ON position. Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1318 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (DRIVER-SIDE) CONNECTOR Turn the ignition switch off. Disconnect the front door latch and lock actuator (driver-side) connector. Inspect the front door latch and lock actuator (driver-side) connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (DRIVER-SIDE) SIGNAL CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between PJB terminal J-06 W (wiring harness-side) and front door latch and lock actuator (driver-side) terminal G (wiring harness-side). Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 5. | ||
| 4 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (DRIVER-SIDE) Inspect the front door latch and lock actuator (driver-side). (See FRONT DOOR LATCH AND LOCK ACTUATOR INSPECTION .) Is there any malfunction? | Yes | Replace the front door latch and lock actuator (driver-side), then go to the next step. (See FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1320 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (PASSENGER-SIDE) CONNECTOR Turn the ignition switch off. Disconnect the front door latch and lock actuator (passenger-side) connector. Inspect the front door latch and lock actuator (passenger-side) connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (PASSENGER-SIDE) SIGNAL CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between PJB terminal J-06 U (wiring harness-side) and front door latch and lock actuator (passenger-side) terminal G (wiring harness-side). Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 5. | ||
| 4 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (PASSENGER-SIDE) Inspect the front door latch and lock actuator (passenger-side). (See FRONT DOOR LATCH AND LOCK ACTUATOR INSPECTION .) Is there any malfunction? | Yes | Replace the front door latch and lock actuator (passenger-side), then go to the next step. (See FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1328 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT REAR DOOR LATCH AND LOCK ACTUATOR (RH) CONNECTOR Turn the ignition switch off. Disconnect the rear door latch and lock actuator (RH) connector. Inspect the rear door latch and lock actuator (RH) connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT REAR DOOR LATCH AND LOCK ACTUATOR (RH) SIGNAL CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between PJB terminal J-06 Q (wiring harness-side) and rear door latch and lock actuator (RH) terminal G (wiring harness-side). Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 5. | ||
| 4 | INSPECT REAR DOOR LATCH AND LOCK ACTUATOR (RIGHT REAR) Inspect the rear door latch and lock actuator (RH). (See REAR DOOR LATCH AND LOCK ACTUATOR INSPECTION .) Is there any malfunction? | Yes | Replace the rear door latch and lock actuator (RH), then go to the next step. (See REAR DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1336 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT DTC Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1342 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT CLIMATE CONTROL UNIT CONNECTOR Disconnect the climate control unit connector. Inspect the climate control unit connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT REAR WINDOW DEFROSTER SWITCH SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-04 AD (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT CLIMATE CONTROL UNIT Inspect the climate control unit. (See CLIMATE CONTROL UNIT INSTALLATION [MANUAL AIR CONDITIONER] .) Is there any malfunction? | Yes | Replace the climate control unit, then go to the next step. (See CLIMATE CONTROL UNIT REMOVAL [MANUAL AIR CONDITIONER] , CLIMATE CONTROL UNIT INSTALLATION [MANUAL AIR CONDITIONER] .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1345 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT REAR WINDOW DEFROSTER RELAY CONNECTOR Turn the ignition switch off. Disconnect the rear window defroster relay connector. Inspect the rear window defroster relay connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 7. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 7. |
| No | Go to the next step. | ||
| 3 | INSPECT REAR WINDOW DEFROSTER RELAY CONTROL CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between PJB terminal J-01 AH (wiring harness-side) and rear window defroster relay terminal E (wiring harness-side). Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible short to GND, then go to Step 7. | ||
| 4 | INSPECT REAR WINDOW DEFROSTER RELAY CONTROL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-01 AH (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 7. |
| No | Go to the next step. | ||
| 5 | INSPECT REAR WINDOW DEFROSTER RELAY CONTROL CIRCUIT FOR SHORT TO POWER SUPPLY Turn the ignition switch to the ON position (Engine off). Measure the voltage between PJB terminal J-01 AH (wiring harness-side) and body GND. Is the voltage B+? | Yes | Repair or replace the wiring harness for a possible short to power supply, then go to Step 7. |
| No | Go to the next step. | ||
| 6 | INSPECT REAR WINDOW DEFROSTER RELAY Inspect the rear window defroster relay. (See RELAY INSPECTION .) Is there any malfunction? | Yes | Replace the rear window defroster relay, then go to the next step. |
| No | Go to the next step. | ||
| 7 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1350 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT WINDSHIELD WIPER MOTOR CONNECTOR Turn the ignition switch off. Disconnect the windshield wiper motor connector. Inspect the windshield wiper motor connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT WINDSHIELD WIPER MOTOR SIGNAL CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between PJB terminal J-01 Al (wiring harness-side) and windshield wiper motor terminal C (wiring harness-side). Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 5. | ||
| 4 | INSPECT WINDSHIELD WIPER MOTOR Inspect the windshield wiper motor. (See WINDSHIELD WIPER MOTOR INSPECTION .) Is there any malfunction? | Yes | Replace the windshield wiper motor, then go to the next step. (See FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1447 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT LIGHT SWITCH CONNECTOR Disconnect the light switch connector. Inspect the light switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT LIGHT SWITCH SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-03 AS (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT LIGHT SWITCH Inspect the light switch. (See LIGHT SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the light switch, then go to the next step. (See LIGHT SWITCH REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1472 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT LIGHT SWITCH CONNECTOR Disconnect the light switch connector. Inspect the light switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT LIGHT SWITCH SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between following terminals: PJB terminal J-04 0 (wiring harness-side) - body GND Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT LIGHT SWITCH Inspect the light switch. Is there any malfunction? | Yes | Replace the light switch, then go to the next step. |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1502 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT LIGHT SWITCH CONNECTOR Disconnect the light switch connector. Inspect the light switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT LIGHT SWITCH SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between following terminals: PJB terminal J-04 K (wiring harness-side) - body GND Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT LIGHT SWITCH Inspect the light switch. Is there any malfunction? | Yes | Replace the light switch, then go to the next step. (See LIGHT SWITCH INSPECTION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1506 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT HOOD LATCH SWITCH CONNECTOR Turn the ignition switch off. Disconnect the hood latch switch connector. Inspect the hood latch switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT HOOD LATCH SWITCH SIGNAL CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between PJB terminal J-02 Y (wiring harness-side) and hood latch switch terminal A (wiring harness-side). Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 5. | ||
| 4 | INSPECT HOOD LATCH SWITCH Inspect the hood latch switch. (See HOOD LATCH SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the hood latch switch, then go to the next step. (See FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1520 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT LIGHT SWITCH CONNECTOR Turn the ignition switch off. Disconnect the light switch connector. Inspect the light switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT LIGHT SWITCH SIGNAL CIRCUIT FOR SHORT TO POWER SUPPLY Turn the ignition switch to the ON position (Engine off). Measure the voltage between PJB terminal J-04 L (wiring harness-side) and body GND. Is the voltage B+? | Yes | Repair or replace the wiring harness for a possible short to power supply, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT LIGHT SWITCH Inspect the light switch. (See LIGHT SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the light switch, then go to the next step. (See LIGHT SWITCH REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1570 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT REAR DOOR LATCH AND LOCK ACTUATOR (LH) CONNECTOR Turn the ignition switch off. Disconnect the rear door latch and lock actuator (LH) connector. Inspect the rear door latch and lock actuator (LH) connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT REAR DOOR LATCH AND LOCK ACTUATOR (LH) SIGNAL CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between PJB terminal J-06 S (wiring harness-side) and rear door latch and lock actuator (LH) terminal G (wiring harness-side). Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 5. | ||
| 4 | INSPECT REAR DOOR LATCH AND LOCK ACTUATOR (LH) Inspect the rear door latch and lock actuator (LH). (See REAR DOOR LATCH AND LOCK ACTUATOR INSPECTION .) Is there any malfunction? | Yes | Replace the rear door latch and lock actuator (LH), then go to the next step. (See REAR DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1572 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT KEY ILLUMINATION CONNECTOR Turn the ignition switch off. Disconnect the key illumination connector. Inspect the key illumination connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT KEY ILLUMINATION SIGNAL CIRCUIT FOR SHORT TO POWER SUPPLY Turn the ignition switch to the ON position (Engine off). Measure the voltage between PJB terminal J-03 AB (wiring harness-side) and body GND. Is the voltage B+? | Yes | Repair or replace the wiring harness for a possible short to power supply, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT KEY ILLUMINATION Inspect the key illumination. Is there any malfunction? | Yes | Replace the key illumination, then go to the next step. (See IGNITION KEY ILLUMINATION BULB REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1607 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH CONNECTOR Disconnect the windshield wiper and washer switch connector. Inspect the windshield wiper and washer switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-04 S (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH Inspect the windshield wiper and washer switch. (See WINDSHIELD WIPER AND WASHER SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the windshield wiper and washer switch, then go to the next step. (See WIPER AND WASHER SWITCH REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1614 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT LIGHT SWITCH CONNECTOR Disconnect the light switch connector. Inspect the light switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT LIGHT SWITCH SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-04 AE (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT LIGHT SWITCH Inspect the light switch. (See LIGHT SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the light switch, then go to the next step. (See LIGHT SWITCH REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1696 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT LIGHT SWITCH CONNECTOR Disconnect the light switch connector. Inspect the light switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT LIGHT SWITCH SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-03 I (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT LIGHT SWITCH Inspect the light switch. (See LIGHT SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the light switch, then go to the next step. (See LIGHT SWITCH REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1798 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT BACK-UP LIGHT SWITCH CONNECTOR Turn the ignition switch off. Disconnect the back-up light switch connector. (MTX) Disconnect the TR switch connector. (ATX) Inspect the switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT BACK-UP LIGHT SWITCH SIGNAL CIRCUIT FOR SHORT TO POWER SUPPLY Turn the ignition switch to the ON position (Engine off). Measure the voltage between PJB terminal J-01 AE (wiring harness-side) and body GND. Is the voltage B+? | Yes | Repair or replace the wiring harness for a possible short to power supply, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT BACK-UP LIGHT SWITCH Inspect the back-up light switch. (MTX) (See BACK-UP LIGHT SWITCH INSPECTION .) Inspect the TR switch. (ATX) (See TRANSAXLE RANGE (TR) SWITCH INSPECTION [FN4A-EL] .) (See TRANSAXLE RANGE (TR) SWITCH INSPECTION [FS5A-EL] .) Is there any malfunction? | Yes | Replace the back-up light switch (MTX) or TR switch (ATX), then go to the next step. (See BACK-UP LIGHT SWITCH REMOVAL/INSTALLATION .) (See TRANSAXLE RANGE (TR) SWITCH REMOVAL/INSTALLATION [FN4A-EL] .) (See TRANSAXLE RANGE (TR) SWITCH REMOVAL/INSTALLATION [FS5A-EL] .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1812 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT HAZARD WARNING SWITCH CONNECTOR Disconnect the hazard warning switch connector. Inspect the hazard warning switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT HAZARD WARNING SWITCH SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-04 AC (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT HAZARD WARNING SWITCH Inspect the hazard warning switch. (See HAZARD WARNING SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the hazard warning switch, then go to the next step. (See HAZARD WARNING SWITCH REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B1873 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT HEADLIGHT CONNECTOR Turn the ignition switch off. Disconnect the headlight (LH) connectors. Inspect the headlight (LH) connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 7. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 7. |
| No | Go to the next step. | ||
| 3 | INSPECT HEADLIGHT CONTROL CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between following terminals: PJB terminal J-01 AA (wiring harness-side) - headlight (LH) terminal A (wiring harness-side) Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 7. | ||
| 4 | INSPECT HEADLIGHT CONTROL CIRCUIT FOR SHORT TO GND Inspect for continuity between following terminals: PJB terminal J-01 AA (wiring harness-side) - body GND Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 7. |
| No | Go to the next step. | ||
| 5 | INSPECT HEADLIGHT CONTROL CIRCUIT FOR SHORT TO POWER SUPPLY Turn the ignition switch to the ON position (Engine off). Measure the voltage between following terminals: PJB terminal J-01 AA (wiring harness-side) - body GND Is the voltage B+? | Yes | Repair or replace the wiring harness for a possible short to power supply, then go to Step 7. |
| No | Go to the next step. | ||
| 6 | INSPECT HEADLIGHT Inspect all the headlight. Is there any malfunction? | Yes | Replace the headlight, then go to the next step. |
| No | Go to the next step. | ||
| 7 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2017 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT HEADLIGHT CONNECTOR Turn the ignition switch off. Disconnect the headlight (RH) connectors. Inspect the headlight (RH) connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 7. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 7. |
| No | Go to the next step. | ||
| 3 | INSPECT HEADLIGHT CONTROL CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between following terminals: PJB terminal J-01 AD (wiring harness-side) - headlight (RH) terminal A (wiring harness-side) Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 7. | ||
| 4 | INSPECT HEADLIGHT CONTROL CIRCUIT FOR SHORT TO GND Inspect for continuity between following terminals: PJB terminal J-01 AD (wiring harness-side) - body GND Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 7. |
| No | Go to the next step. | ||
| 5 | INSPECT HEADLIGHT CONTROL CIRCUIT FOR SHORT TO POWER SUPPLY Turn the ignition switch to the ON position (Engine off). Measure the voltage between following terminals: PJB terminal J-01 AD (wiring harness-side) - body GND Is the voltage B+? | Yes | Repair or replace the wiring harness for a possible short to power supply, then go to Step 7. |
| No | Go to the next step. | ||
| 6 | INSPECT HEADLIGHT Inspect all the headlight. Is there any malfunction? | Yes | Replace the headlight, then go to the next step. |
| No | Go to the next step. | ||
| 7 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2018 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT CLIMATE CONTROL UNIT CONNECTOR Turn the ignition switch off. Disconnect the climate control unit connector. Inspect the climate control unit connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT CLIMATE CONTROL UNIT SIGNAL CIRCUIT FOR SHORT TO POWER SUPPLY Turn the ignition switch to the ON position (Engine off). Measure the voltage between PJB terminal J-04 1 (wiring harness-side) and body GND. Is the voltage B+? | Yes | Repair or replace the wiring harness for a possible short to power supply, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT CLIMATE CONTROL UNIT Inspect the climate control unit. (See CLIMATE CONTROL UNIT INSPECTION [MANUAL AIR CONDITIONER] .) Is there any malfunction? | Yes | Replace the climate control unit, then go to the next step. (See CLIMATE CONTROL UNIT REMOVAL [MANUAL AIR CONDITIONER] , CLIMATE CONTROL UNIT INSTALLATION [MANUAL AIR CONDITIONER] .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2060 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (DRIVER-SIDE) CONNECTOR Disconnect the front door latch and lock actuator (driver-side) connector. Inspect the front door latch and lock actuator (driver-side) connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (DRIVER-SIDE) SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-06 AA (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (DRIVER-SIDE) Inspect the front door latch and lock actuator (driver-side). (See FRONT DOOR LATCH AND LOCK ACTUATOR INSPECTION .) Is there any malfunction? | Yes | Replace the front door latch and lock actuator (driver-side), then go to the next step. (See FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2095 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (DRIVER-SIDE) CONNECTOR Disconnect the front door latch and lock actuator (driver-side) connector. Inspect the front door latch and lock actuator (driver-side) connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (DRIVER-SIDE) SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-06 Y (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (DRIVER-SIDE) Inspect the front door latch and lock actuator (driver-side). (See FRONT DOOR LATCH AND LOCK ACTUATOR INSPECTION .) Is there any malfunction? | Yes | Replace the front door latch and lock actuator (driver-side), then go to the next step. (See FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2096 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH CONNECTOR Turn the ignition switch off. Disconnect the windshield wiper and washer switch connector. Inspect the windshield wiper and washer switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH SIGNAL CIRCUIT FOR SHORT TO POWER SUPPLY Turn the ignition switch to the ON position (Engine off). Measure the voltage between PJB terminal J-03 B (wiring harness-side) and body GND. Is the voltage B+? | Yes | Repair or replace the wiring harness for a possible short to power supply, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH Inspect the windshield wiper and washer switch. (See WINDSHIELD WIPER AND WASHER SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the windshield wiper and washer switch, then go to the next step. (See WIPER AND WASHER SWITCH REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2114 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT CLIMATE CONTROL UNIT CONNECTOR Disconnect the climate control unit connector. Inspect the climate control unit connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT CLIMATE CONTROL UNIT SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-04 AF (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT CLIMATE CONTROL UNIT Inspect the climate control unit. (See CLIMATE CONTROL UNIT INSPECTION [MANUAL AIR CONDITIONER] .) Is there any malfunction? | Yes | Replace the climate control unit, then go to the next step. (See CLIMATE CONTROL UNIT REMOVAL [MANUAL AIR CONDITIONER] , CLIMATE CONTROL UNIT INSTALLATION [MANUAL AIR CONDITIONER] .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2175 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH CONNECTOR Disconnect the windshield wiper and washer switch connector. Inspect the windshield wiper and washer switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-04 G (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH Inspect the windshield wiper and washer switch. (See WINDSHIELD WIPER AND WASHER SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the windshield wiper and washer switch, then go to the next step. (See WIPER AND WASHER SWITCH REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2180 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH CONNECTOR Disconnect the windshield wiper and washer switch connector. Inspect the windshield wiper and washer switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-04 C (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH Inspect the windshield wiper and washer switch. (See WINDSHIELD WIPER AND WASHER SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the windshield wiper and washer switch, then go to the next step. (See WIPER AND WASHER SWITCH REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2181 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT PANEL LIGHT CONTROL SWITCH CONNECTOR Turn the ignition switch off. Disconnect the panel light control switch connector. Inspect the panel light control switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 7. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 7. |
| No | Go to the next step. | ||
| 3 | INSPECT PANEL LIGHT CONTROL SWITCH CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between PJB terminal J-03 AJ (wiring harness-side) and panel light control switch terminal H (wiring harness-side). Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 7. | ||
| 4 | INSPECT PANEL LIGHT CONTROL SWITCH CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-03 AJ (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 7. |
| No | Go to the next step. | ||
| 5 | INSPECT PANEL LIGHT CONTROL SWITCH CIRCUIT FOR SHORT TO POWER SUPPLY Turn the ignition switch to the ON position (Engine off). Measure the voltage between PJB terminal J-03 AJ (wiring harness-side) and body GND. Is the voltage B+? | Yes | Repair or replace the wiring harness for a possible short to power supply, then go to Step 7. |
| No | Go to the next step. | ||
| 6 | INSPECT PANEL LIGHT CONTROL SWITCH Inspect the panel light control switch. (See PANEL LIGHT CONTROL SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the panel light control switch, then go to the next step. (See PANEL LIGHT CONTROL SWITCH REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 7 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2212 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT DOOR LOCK SWITCH CONNECTOR Disconnect the door lock switch connector. Inspect the door lock switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT DOOR LOCK SWITCH SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-06 T (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT DOOR LOCK SWITCH Inspect the door lock switch. (See DOOR LOCK SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the door lock switch, then go to the next step. (See DOOR LOCK SWITCH REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2218 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT LIGHT SWITCH CONNECTOR Disconnect the light switch connector. Inspect the light switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT LIGHT SWITCH SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-04 W (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT LIGHT SWITCH Inspect the light switch. (See LIGHT SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the light switch, then go to the next step. (See LIGHT SWITCH REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2254 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH CONNECTOR Turn the ignition switch off. Disconnect the windshield wiper and washer switch connector. Inspect the windshield wiper and washer switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 8. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 8. |
| No | Go to the next step. | ||
| 3 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between PJB terminal J-04 U (wiring harness-side) and windshield wiper and washer switch terminal G (wiring harness-side). Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 8. | ||
| 4 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-04 U (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 8. |
| No | Go to the next step. | ||
| 5 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH CIRCUIT FOR SHORT TO POWER SUPPLY Turn the ignition switch to the ON position (Engine off). Measure the voltage between PJB terminal J-04 U (wiring harness-side) and body GND. Is the voltage B+ | Yes | Repair or replace the wiring harness for a possible short to power supply, then go to Step 8. |
| No | Go to the next step. | ||
| 6 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-04 E (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 8. |
| No | Go to the next step. | ||
| 7 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH Inspect the windshield wiper and washer switch. (See WINDSHIELD WIPER AND WASHER SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the windshield wiper and washer switch, then go to the next step. (See WIPER AND WASHER SWITCH REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 8 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2259 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT DTC Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Perform PJB configuration procedure. (See PASSENGER JUNCTION BOX (PJB) CONFIGURATION .) Go to the next step. |
| No | Go to the next step. | ||
| 2 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2477 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT PARKING BRAKE SWITCH CONNECTOR Turn the ignition switch off. Disconnect the parking brake switch connector. Inspect the parking brake switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT PARKING BRAKE SWITCH SIGNAL CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between PJB terminal J-04 AB (wiring harness-side) and parking brake switch terminal A (wiring harness-side). Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 5. | ||
| 4 | INSPECT PARKING BRAKE SWITCH Inspect the parking brake switch. (See PARKING BRAKE SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the parking brake switch, then go to the next step. |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2479 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT FRONT FOG LIGHT RELAY CONNECTOR Turn the ignition switch off. Disconnect the front fog light relay connector. Inspect the front fog light relay connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 7. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 7. |
| No | Go to the next step. | ||
| 3 | INSPECT FRONT FOG LIGHT RELAY CONTROL CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between PJB terminal J-02 X (wiring harness-side) and front fog light relay terminal E (wiring harness-side). Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for open circuit, then go to Step 7. | ||
| 4 | INSPECT FRONT FOG LIGHT RELAY CONTROL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-02 X (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 7. |
| No | Go to the next step. | ||
| 5 | INSPECT FRONT FOG LIGHT RELAY CONTROL CIRCUIT FOR SHORT TO POWER SUPPLY Turn the ignition switch to the ON position (Engine off). Measure the voltage between PJB terminal J-02 X (wiring harness-side) and body GND. Is the voltage B+ ? | Yes | Repair or replace the wiring harness for a possible short to power supply, then go to Step 7. |
| No | Go to the next step. | ||
| 6 | INSPECT FRONT FOG LIGHT RELAY Inspect the front fog light relay. (See RELAY INSPECTION .) Is there any malfunction? | Yes | Replace the front fog light relay, then go to the next step. |
| No | Go to the next step. | ||
| 7 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2512 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT INTERIOR LIGHT AND MAP LIGHT CONNECTORS Turn the ignition switch off. Disconnect the interior light and map light connectors. Inspect the interior light and map light connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 6. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 6. |
| No | Go to the next step. | ||
| 3 | INSPECT INTERIOR LIGHT AND MAP LIGHT CONTROL CIRCUIT FOR SHORT TO POWER SUPPLY Turn the ignition switch to the ON position (Engine off). Measure the voltage between PJB terminal J-05 U (wiring harness-side) and body GND. Is the voltage B+? | Yes | Repair or replace the wiring harness for a possible short to power supply, then go to Step 6. |
| No | Go to the next step. | ||
| 4 | INSPECT INTERIOR LIGHT AND MAP LIGHT CONTROL CIRCUIT FOR OPEN CIRCUIT Turn the ignition switch off. Inspect for continuity between following terminals: PJB terminal J-05 U (wiring harness-side) - interior light terminal C (wiring harness-side) PJB terminal J-05 U (wiring harness-side) - map light terminal C (wiring harness-side) Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 6. | ||
| 5 | INSPECT INTERIOR LIGHT AND MAP LIGHT Inspect the interior light and map light. (See INTERIOR LIGHT INSPECTION , MAP LIGHT INSPECTION .) Is there any malfunction? | Yes | Replace the interior light or map light, then go to the next step. (See INTERIOR LIGHT REMOVAL/INSTALLATION , MAP LIGHT REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 6 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2555 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT TRUNK LID KEY CYLINDER SWITCH CONNECTOR Disconnect the trunk lid key cylinder switch connector. Inspect the trunk lid key cylinder switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT TRUNK LID KEY CYLINDER SWITCH SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-06 P (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT TRUNK LID KEY CYLINDER SWITCH Inspect the trunk lid key cylinder switch. (See TRUNK LID KEY CYLINDER SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the trunk lid key cylinder switch, then go to the next step. (See TRUNK LID KEY CYLINDER REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2559 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (DRIVER-SIDE) CONNECTOR Disconnect the front door latch and lock actuator (driver-side) connector. Inspect the front door latch and lock actuator (driver-side) connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (DRIVER-SIDE) SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-06 AC (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT FRONT DOOR LATCH AND LOCK ACTUATOR (DRIVER-SIDE) Inspect the front door latch and lock actuator (driver-side). (See FRONT DOOR LATCH AND LOCK ACTUATOR INSPECTION .) Is there any malfunction? | Yes | Replace the front door latch and lock actuator (driver-side), then go to the next step. (See FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2574 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT TRUNK LID LATCH SWITCH CONNECTOR Disconnect the trunk lid latch switch connector. Inspect the trunk lid latch switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT TRUNK LID LATCH SWITCH SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-06 Z (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT TRUNK LID LATCH SWITCH Inspect the trunk lid latch switch. (See TRUNK LID LATCH SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the trunk lid latch switch, then go to the next step. (See TRUNK LID LATCH REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2721 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT DTC Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2897 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT TURN LIGHT CONNECTOR Turn the ignition switch off. Disconnect all the turn light (RH) connectors. Inspect all the turn light (RH) connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 7. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 7. |
| No | Go to the next step. | ||
| 3 | INSPECT TURN LIGHT CONTROL CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between following terminals: PJB terminal J-01 L (wiring harness-side) - front turn light (RH) terminal A (wiring harness-side) PJB terminal J-01 L (wiring harness-side) - front side turn light (RH) terminal A (wiring harness-side) PJB terminal J-05 AK (wiring harness-side) - rear turn light (RH) terminal A (wiring harness-side) Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 7. | ||
| 4 | INSPECT TURN LIGHT CONTROL CIRCUIT FOR SHORT TO GND Inspect for continuity between following terminals: PJB terminal J-01 L (wiring harness-side) - body GND PJB terminal J-01 L (wiring harness-side) - body GND PJB terminal J-05 AK (wiring harness-side) - body GND Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 7. |
| No | Go to the next step. | ||
| 5 | INSPECT TURN LIGHT CONTROL CIRCUIT FOR SHORT TO POWER SUPPLY Turn the ignition switch to the ON position (Engine off). Measure the voltage between following terminals: PJB terminal J-01 L (wiring harness-side) - body GND PJB terminal J-01 L (wiring harness-side) - body GND PJB terminal J-05 AK (wiring harness-side) - body GND Is the voltage B+? | Yes | Repair or replace the wiring harness for a possible short to power supply, then go to Step 7. |
| No | Go to the next step. | ||
| 6 | INSPECT TURN LIGHT Inspect all the turn lights. Is there any malfunction? | Yes | Replace the turn lights, then go to the next step. |
| No | Go to the next step. | ||
| 7 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2898 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT TURN LIGHT CONNECTOR Turn the ignition switch off. Disconnect all the turn light (LH) connectors. Inspect all the turn light (LH) connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 7. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 7. |
| No | Go to the next step. | ||
| 3 | INSPECT TURN LIGHT CONTROL CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between following terminals: PJB terminal J-01 AK (wiring harness-side) - front turn light (LH) terminal A (wiring harness-side) PJB terminal J-01 AK (wiring harness-side) - front side turn light (LH) terminal A (wiring harness-side) PJB terminal J-05 A (wiring harness-side) - rear turn light (LH) terminal A (wiring harness-side) Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 7. | ||
| 4 | INSPECT TURN LIGHT CONTROL CIRCUIT FOR SHORT TO GND Inspect for continuity between following terminals: PJB terminal J-01 AK (wiring harness-side) - body GND PJB terminal J-01 AK (wiring harness-side) - body GND PJB terminal J-05 A (wiring harness-side) - body GND Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 7. |
| No | Go to the next step. | ||
| 5 | INSPECT TURN LIGHT CONTROL CIRCUIT FOR SHORT TO POWER SUPPLY Turn the ignition switch to the ON position (Engine off). Measure the voltage between following terminals: PJB terminal J-01 AK (wiring harness-side) - body GND PJB terminal J-01 AK (wiring harness-side) - body GND PJB terminal J-05 A (wiring harness-side) - body GND Is the voltage B+? | Yes | Repair or replace the wiring harness for a possible short to power supply, then go to Step 7. |
| No | Go to the next step. | ||
| 6 | INSPECT TURN LIGHT Inspect all the turn lights. Is there any malfunction? | Yes | Replace the turn lights, then go to the next step. |
| No | Go to the next step. | ||
| 7 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2899 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH CONNECTOR Turn the ignition switch off. Disconnect the windshield wiper and washer switch connector. Inspect the windshield wiper and washer switch connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH SIGNAL CIRCUIT FOR SHORT TO POWER SUPPLY Turn the ignition switch to the ON position (Engine off). Measure the voltage between PJB terminal J-03 B (wiring harness-side) and body GND. Is the voltage B+? | Yes | Repair or replace the wiring harness for a possible short to power supply, then go to Step 5. |
| No | Go to the next step. | ||
| 4 | INSPECT WINDSHIELD WIPER AND WASHER SWITCH Inspect the windshield wiper and washer switch. (See WINDSHIELD WIPER AND WASHER SWITCH INSPECTION .) Is there any malfunction? | Yes | Replace the windshield wiper and washer switch, then go to the next step. (See WIPER AND WASHER SWITCH REMOVAL/INSTALLATION .) |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Turn the ignition switch to LOCK position then ON position. Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | DTC troubleshooting completed. | ||
DTC B2966 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT BRAKE FLUID LEVEL SENSOR CONNECTOR Turn the ignition switch off. Disconnect the brake fluid level sensor connector. Inspect the brake fluid level sensor connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 5. |
| No | Go to the next step. | ||
| 3 | INSPECT BRAKE FLUID LEVEL SENSOR SIGNAL CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between following terminals: PJB terminal J-01 AL (wiring harness-side) - brake fluid level sensor terminal B (wiring harness-side) Brake fluid level sensor terminal A (wiring harness-side) - body GND Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 5. | ||
| 4 | INSPECT BRAKE FLUID LEVEL SENSOR Inspect the brake fluid level sensor. (See BRAKE FLUID LEVEL SENSOR INSPECTION .) Is there any malfunction? | Yes | Replace the brake fluid level sensor, then go to the next step. |
| No | Go to the next step. | ||
| 5 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | Troubleshooting completed. | ||
DTC C1189 DIAGNOSTIC PROCEDURE
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
| 1 | INSPECT RAIN SENSOR CONNECTOR Turn the ignition switch off. Disconnect the rain sensor connector. Inspect the rain sensor connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 6. |
| No | Go to the next step. | ||
| 2 | INSPECT PJB CONNECTOR Disconnect the PJB connector. Inspect the PJB connector terminals for poor connection (such as damaged/pulled-out pins, and corrosion). Is there any malfunction? | Yes | Repair or replace the terminal, then go to Step 6. |
| No | Go to the next step. | ||
| 3 | INSPECT RAIN SENSOR CIRCUIT FOR OPEN CIRCUIT Inspect for continuity between PJB terminal J-06 AD (wiring harness-side) and rain sensor terminal C (wiring harness-side). Is there continuity? | Yes | Go to the next step. |
| No | Repair or replace the wiring harness for a possible open circuit, then go to Step 6. | ||
| 4 | INSPECT RAIN SENSOR SIGNAL CIRCUIT FOR SHORT TO GND Inspect for continuity between PJB terminal J-06 AD (wiring harness-side) and body GND. Is there continuity? | Yes | Repair or replace the wiring harness for a possible short to GND, then go to Step 6. |
| No | Go to the next step. | ||
| 5 | INSPECT RAIN SENSOR SIGNAL CIRCUIT FOR SHORT TO POWER SUPPLY Turn the ignition switch to the ON position (Engine off). Measure the voltage between PJB terminal J-06 AD (wiring harness-side) and body GND. Is the voltage B+ ? | Yes | Repair or replace the wiring harness for a possible short to power supply, then go to the next step. |
| No | Replace the Rain sensor, then go to the next step. (See RAIN SENSOR REMOVAL/INSTALLATION .) | ||
| 6 | VERIFY TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PJB memory using the M-MDS. Perform the self-test. (See PJB SELF-TEST [CONTROL SYSTEM] ). Is the same DTC present? | Yes | Replace the PJB. (See PASSENGER JUNCTION BOX (PJB) REMOVAL/INSTALLATION .) |
| No | Troubleshooting completed. | ||
DTC U2030 DIAGNOSTIC PROCEDURE
Scheme 206
![Scheme 206: PJB SELF-TEST [CONTROL SYSTEM]](https://i.diagnostdata.com/repair/a3/a35f39a97f0b6207994d779ba3437597bd7f77a56b980c779665a8cb24951926.webp)
- Connect the M-MDS to the DLC-2.
- Set up the M-MDS (including the vehicle recognition).
- Verify the following vehicle conditions: Ignition switch is at ON position. All the switches are turned off (except the ignition switch). All the doors, hood, and trunk lid or liftgate are closed. All the doors, and trunk lid or liftgate are unlocked. Parking brake lever is pulled.
- Perform procedures according to directions on the M-MDS screen.
- Verify if any DTCs are displayed. If any DTCs are displayed, perform the troubleshooting according to the corresponding DTC inspection.
- Disconnect the M-MDS.