Inspection and Verification
This service information provides step-by-step module configuration procedures. Carry out the Programmable Module Installation (PMI) procedure in this service information when another article directs to carry out configuration or when DTCs from the below list are present
DTC Table
Note. Some modules on this vehicle utilize a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground. Continuous Memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
| DTC | Description | Source | Action |
|---|---|---|---|
| B2477 | Module Configuration Failure | Driver Door Module (DDM) Driver Seat Module (DSM) Dual Climate Controlled Seat Module (DCSM) Front Display Interface Module (FDIM) Parking Aid Module (PAM) Smart Junction Box (SJB) | CARRY OUT Programmable Module Installation (PMI). REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| B2900 | VIN mismatch | ABS module (except Hybrid) 4X4 control module | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| P0602 | Powertrain Control Module Programming Error | PCM | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| P0605 | Internal Control Module Read Only Memory (ROM) Error | PCM | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| P0613:45 | TCM Processor: Program Memory Failure | Transmission Control Module (TCM) (Hybrid only) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| P0613:46 | TCM Processor: Calibration/Parameter Memory Failure | TCM (Hybrid only) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| P1639 | Vehicle ID Block Corrupted, Not Programmed | PCM | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U0300 | Internal Control Module Software Incompatibility | PCM | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U0300:00 | Internal Control Module Software Incompatibility: No Sub Type Information | DC to DC Converter Control Module (DC/DC) (Hybrid only) Restraints Control Module (RCM) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U0300:05 | Internal Control Module Software Incompatibility: System Programming Failure | Battery Energy Control Module (BECM) (Hybrid only) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U0300:51 | Internal Control Module Software Incompatibility: Not Programmed | ABS module (Hybrid only) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U0335:00 | Software Incompatibility with Hybrid Battery Pack Sensor Module: No Sub Type Information | BECM (Hybrid only) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U0336:00 | Software Incompatibility with Restraints Control Module: No Sub Type Information | BECM (Hybrid only) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | Audio Digital Signal Processing (DSP) module Audio Control Module (ACM) Front Controls Interface Module (FCIM) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U2050 | No Application Present | 4X4 control module ABS module (except Hybrid) ACM DCSM DDM DSM FDIM FCIM Interior Lighting Control Module (ILCM) SJB Transmission Control Module (TCM) (except Hybrid) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U2051 | No Application Present | 4X4 control module ACM FCIM FDIM PAM | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | ABS module (Hybrid only) ACM Audio DSP module HVAC module Instrument Panel Cluster (IPC) Power Steering Control Module (PSCM) RCM Side Obstacle Detection Control Module - Left (SOD-L) Side Obstacle Detection Control Module - Right (SOD-R) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | Accessory Protocol Interface Module (APIM) | CARRY OUT APIM programming. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) PROGRAMMING . |
| U2100:56 | Initial Configuration Not Complete: Invalid/Incompatible Configuration | ABS module (Hybrid only) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | ACM Audio DSP module PSCM | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U3000:45 | Control Module: Program Memory Failure | DC/DC (Hybrid only) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U3000:46 | Control Module: Calibration/Parameter Memory Failure | Accessory Protocol Interface Module (APIM) Headlamp Control Module (HCM) IPC PSCM RCM | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U3000:54 | Control Module: Missing Calibration | Occupant Classification System Module (OCSM) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U3002:62 | Vehicle Identification Number: Signal Compare Failure | ABS module (Hybrid only) HVAC module RCM | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
DTC TABLE
Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is Available
Note. Following module installation, some modules require a separate learning procedure be carried out. For adaptive learning and calibration instructions, refer to the specific module removal and installation procedures.
- Connect the IDS and identify the vehicle as normal.
- From the Toolbox icon, select Module Programming and press the check mark.
- Select Programmable Module Installation.
- Select the module that is being replaced.
- Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
- Install the new module and press the check mark.
- Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
- The IDS downloads the data into the new module and displays Module Configuration Complete.
- Test module for correct operation.
Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is NOT Available
Note. Following module installation, some modules require a separate learning procedure be carried out. For adaptive learning and calibration instructions, refer to the specific module removal and installation procedures.
- Install the new module.
- Connect the IDS and identify the vehicle as normal.
- From the Toolbox icon, select Module Programming and press the check mark.
- Select Programmable Module Installation.
- Select the module that was replaced.
- Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
- Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
- If the data is not available, the IDS displays a screen stating to contact the As-Built Data Center. Retrieve the data from the technician service publication website at this time and press the check mark.
- Enter the module data and press the check mark.
- The IDS downloads the data into the new module and displays Module Configuration Complete.
- Test module for correct operation.
Accessory Protocol Interface Module (APIM) Programming Using the Integrated Diagnostic System (IDS)
Note. If a new Accessory Protocol Interface Module (APIM) is being installed, install the new APIM before carrying out the following procedure. For additional information, refer to REMOVAL AND INSTALLATION .
- Turn the Audio Control Module (ACM) on.
- Connect the scan tool to the Data Link Connector (DLC).
- Connect one end of the Universal Serial Bus (USB) male-A to male-A cable to the scan tool.
- Connect the other end of the USB male-A to male-A cable to the vehicle USB port.
- From the technician service publication website, run On-Line Automotive Service Information System (OASIS) using Quick Start or by manually entering the Vehicle Identification Number (VIN).
- From the OASIS tab, select the "Sync/APIM" bullet.
- Select the "Read APIM" button to verify the current APIM Vehicle Interface Processor (VIP) and Consumer Interface Processor (CIP) software levels.
- Select the desired software level from the list of available software for programming then select the "Program APIM" button to begin the APIM programming process. Enter the APIM As-Built data if prompted. When only the CIP is being programmed, select cancel when prompted whether or not to program the VIP. When the VIP is programmed, the CIP will be programmed automatically. NOTE: Do not disconnect the Vehicle Communication Module (VCM) or USB cables during APIM programming.
- The Sync/APIM application downloads the software into the APIM and displays "Programming has been completed successfully".
- Test the audio system for correct operation.