Home ReviewsRefund Car not listed?
Home/Land Rover/Freelander/Land Rover Freelander II facelift (2010-2012)/Repair manual/Engine Control Systems/Electronic Engine Controls: Removal & Installation
Contents Wiring diagrams Section: Engine Control Systems All sections

Electronic Engine Controls: Removal & Installation Land Rover Freelander II facelift

Engine Control Systems 15 illustrations ~463 words

REMOVAL

Note. Removal steps in this procedure may contain installation details.

Scheme 3

Scheme 3: REMOVAL
Scheme 3: REMOVAL

Scheme 4

Scheme 4
Scheme 4
  1. Remove the engine cover. Refer to ENGINE COVER - 3.2L .
  2. Torque: 10 Nm

INSTALLATION

  1. To install, reverse the removal procedure.

Note. Removal steps in this procedure may contain installation details.

Scheme 5

Scheme 5: REMOVAL
Scheme 5: REMOVAL
  1. Raise and support the vehicle.
  2. Remove the engine undershield. Refer to ENGINE UNDERSHIELD .
  3. Torque: 10 Nm
  1. To install, reverse the removal procedure.

Note. Removal steps in this procedure may contain installation details.

Scheme 6

Scheme 6: REMOVAL
Scheme 6: REMOVAL
  1. Raise and support the vehicle.
  2. Remove the intake manifold assembly. Refer to INTAKE MANIFOLD .
  3. Remove the ECT sensor.
  1. To install, reverse the removal procedure.
  1. For H02S anti-seize compound information, refer to the specification information.
  2. Apply anti-seize compound to the sensor threads.
  3. Install the HO2S. Wrench, H02S (310-121) Torque: 45 Nm
  4. Connect the HO2S electrical connector.
  5. Install the engine cover. Refer to ENGINE COVER .
  1. To install, reverse the removal procedure.
  2. If required, carry out a long drive cycle. See POWERTRAIN CONTROL MODULE (PCM) LONG DRIVE CYCLE SELF-TEST .

Scheme 7

Scheme 7: REMOVAL
Scheme 7: REMOVAL
  1. Torque: 2 Nm
  1. To install, reverse the removal procedure.
  2. If required, carry out a short drive cycle. See POWERTRAIN CONTROL MODULE (PCM) SHORT DRIVE CYCLE SELF-TEST .

Scheme 8

Scheme 8: REMOVAL
Scheme 8: REMOVAL

Scheme 9

Scheme 9
Scheme 9

Scheme 10

Scheme 10
Scheme 10

Scheme 11

Scheme 11
Scheme 11
  1. Raise and support the vehicle.
  2. Remove the engine undershield. Refer to ENGINE UNDERSHIELD .
  1. To install, reverse the removal procedure.
  2. If required, carry out a short drive cycle. See POWERTRAIN CONTROL MODULE (PCM) SHORT DRIVE CYCLE SELF-TEST .

Note. Removal steps in this procedure may contain installation details.

Scheme 12

Scheme 12: REMOVAL
Scheme 12: REMOVAL

Scheme 13

Scheme 13
Scheme 13

Scheme 14

Scheme 14
Scheme 14
  1. Remove the cover and disconnect the battery ground cable. Refer to SPECIFICATIONS .
  2. Remove the plenum chamber panel. Refer to PLENUM CHAMBER .
  3. Petrol ECM shown, diesel similar.
  4. Torque: 6 Nm
  1. To install, reverse the removal procedure.
  2. Renew the engine oil and filter. Engine Oil Draining and Filling. Refer to ENGINE OIL DRAINING AND FILLING .
  3. If a new component has been installed, configure using Land Rover approved diagnostic equipment.

Note. Removal steps in this procedure may contain installation details.

Scheme 15

Scheme 15: REMOVAL
Scheme 15: REMOVAL
  1. Remove the cover and disconnect the battery ground cable. Refer to SPECIFICATIONS .
  2. Remove the fuel rail. Refer to FUEL RAIL .
  3. Torque: 6 Nm
  1. To install, reverse the removal procedure.

Note. Removal steps in this procedure may contain installation details.

Scheme 16

Scheme 16: REMOVAL
Scheme 16: REMOVAL
  1. Raise and support the vehicle.
  2. Remove the oil cooler assembly. Refer to OIL COOLER .
  3. Remove the knock sensor (KS). Torque: 20 Nm
  1. To install, reverse the removal procedure.

Note. Removal steps in this procedure may contain installation details.

Scheme 17

Scheme 17: REMOVAL
Scheme 17: REMOVAL
  1. Raise and support the vehicle.
  2. Remove the intake manifold. Refer to INTAKE MANIFOLD .
  3. Remove the knock sensor (KS). Torque: 20 Nm
  1. To install, reverse the removal procedure.

More articles — Electronic Engine Controls