Home ReviewsRefund
Home/Infiniti/M45/Infiniti M45 II (2002-2004)/Repair manual/Automatic Transaxle/CONSULT-II setting procedure
Contents Wiring diagrams Section: Automatic Transaxle All sections

CONSULT-II setting procedure Infiniti M45 II

Automatic Transaxle 24 illustrations ~294 words

CONSULT-II setting procedure

  1. For details, refer to the separate "CONSULT-II Operations Manual".

Scheme 355

Scheme 355
Scheme 355

Scheme 356

Scheme 356
Scheme 356

Scheme 357

Scheme 357
Scheme 357

Scheme 358

Scheme 358
Scheme 358
  1. Turn ignition switch "OFF" position.
  2. Connect CONSULT-II and CONSULT-II CONVERTER to data link connector, which is located in instrument lower panel on driver side.
  3. Turn ignition switch "ON" position.
  4. Touch "START".
  5. Touch "ENGINE" for OBD-II detected items or touch "A/T" for TCM self- diagnosis. If "A/T" or "ENGINE" is not indicated, go to "CONSULT-II DATA LINK CONNECTOR (DLC) CIRCUIT ".
  6. Touch "SELF-DIAG RESULTS". Display shows malfunction experienced since the last erasing operation. CONSULT-II performs REAL-TIME SELF-DIAGNOSIS. Also, any malfunction detected while in this mode will be displayed at real time.

Scheme 359

Scheme 359: Self- diagnostic result test mode
Scheme 359: Self- diagnostic result test mode

Scheme 360

Scheme 360
Scheme 360

Scheme 361

Scheme 361
Scheme 361

Scheme 362

Scheme 362
Scheme 362

Scheme 363

Scheme 363: Data monitor mode (A/T)
Scheme 363: Data monitor mode (A/T)

Scheme 364

Scheme 364
Scheme 364

Scheme 365

Scheme 365
Scheme 365

Scheme 366

Scheme 366
Scheme 366
  1. For details, refer to the separate "CONSULT-II Operation Manual".

Scheme 367

Scheme 367
Scheme 367

Scheme 368

Scheme 368
Scheme 368

Scheme 369

Scheme 369
Scheme 369

Scheme 370

Scheme 370
Scheme 370

Scheme 371

Scheme 371
Scheme 371

Scheme 372

Scheme 372
Scheme 372

Scheme 373

Scheme 373
Scheme 373

Scheme 374

Scheme 374
Scheme 374

Scheme 375

Scheme 375
Scheme 375

Scheme 376

Scheme 376
Scheme 376

Scheme 377

Scheme 377
Scheme 377

Scheme 378

Scheme 378
Scheme 378
  1. Turn ignition switch "OFF".
  2. Connect CONSULT-II and CONSULT-II CONVERTER to data link connector, which is located in instrument lower panel on driver side.
  3. Turn ignition switch "ON".
  4. Touch "START".
  5. Touch "A/T". If "A/T" is not indicated, go to "CONSULT-II DATA LINK CONNECTOR (DLC) CIRCUIT ".
  6. Touch "DTC WORK SUPPORT".
  7. Touch select item menu.
  8. Touch "START".
  9. Perform driving test according to "DTC CONFIRMATION PROCEDURE" in "TROUBLE DIAGNOSIS FOR DTC". When testing conditions are satisfied, CONSULT-II screen changes from "OUT OF CONDITION" to "TESTING".
  10. Stop vehicle. If "NG" appears on the screen, malfunction may exist. Go to "DIAGNOSTIC PROCEDURE".
  11. Perform test drive to check gear shift feeling in accordance with instructions displayed.
  12. Touch "YES" or "NO".
  13. CONSULT-II procedure is ended. If "NG" appears on the screen, a malfunction may exist. Go to "DIAGNOSTIC PROCEDURE".