Module Communications Network - Module Configuration: Diagnosis Ford Mustang V рестайлинг

Inspection and Verification

This service information provides step-by-step module configuration procedures. Carry out the Programmable Module Installation (PMI) procedures in this service information when another workshop service information directs to carry out configuration or when DTCs from the list below are present

DTC Chart

Note. Some modules on this vehicle utilize a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground.

Continuous Memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.

DTC CHART

Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is Available

Note. Following module installation, some modules require a separate procedure be carried out. For instructions, refer to the specific module removal and installation procedures .

1. Connect the IDS and identify the vehicle as normal.
2. From the Toolbox icon, select Module Programming and press the check mark.
3. Select Programmable Module Installation.
4. Select the module that is being replaced.
5. Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
6. Install the new module and press the check mark.
7. Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
8. The IDS downloads the data into the new module and displays Module Configuration Complete.
9. Test module for correct operation.

Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is NOT Available

Note. Following module installation, some modules require a separate procedure be carried out. For instructions, refer to the specific module removal and installation procedures .

1. Install the new module.
2. Connect the IDS and identify the vehicle as normal.
3. From the Toolbox icon, select Module Programming and press the check mark.
4. Select Programmable Module Installation.
5. Select the module that was replaced.
6. Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
7. Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
8. If the data is not available, the IDS displays a screen stating to contact the As-Built Data Center. Retrieve the data from the technician service publication website at this time and press the check mark.
9. Enter the module data and press the check mark.
10. The IDS downloads the data into the new module and displays Module Configuration Complete.
11. Test module for correct operation.

Accessory Protocol Interface Module (APIM) Programming Using the Integrated Diagnostic System (IDS)

Note. If a new Accessory Protocol Interface Module (APIM) is being installed, install a new APIM before carrying out the following procedure. For additional information, refer to DRIVER INFORMATION SYSTEM & ENTERTAINMENT SYSTEM article. When carrying out the programming procedures, follow the scan tool on-screen directions. Make sure the battery is fully charged before carrying out the programming steps. A hardwired internet connection is strongly recommended when programming. If unable to complete programming because operation stops or errors are received, internet browser settings may need to be configured. From the on-line OASIS tab, select the "Service Tips" tab, then select "SYNC Software Programming" under "Job Aids".

Note. For APIM flash programming: The scan tool and a USB male A to male A cable (CCMUSB2-AM-AM-10 or equivalent) are required. The flash procedure deletes any paired phones that were in the SYNC® system. The file for the flash needs to be downloaded from the online database. Allow for extra time for the file to download. The files are approximately 80 megabyte.

1. Open a session for the vehicle from the technician service publication web site, and run On-Line Automotive Service Information System (OASIS) using "Read VIN and DTC's".
2. From the OASIS tab, select the "SYNC" button.
3. There are 3 available options for APIM programming: Standard (latest version of current software and applications): Use this option to update the APIM to the latest software level. Custom (show what's available, and let me choose): Use this option to show all the available options that can be programmed, or if a Technical Service Bulletin (TSB) directs for specific software version to be programmed. Module Replacement (restore software for newly installed hardware): Use this option when the APIM has been replaced.
4. After selecting 1 of the 3 options (Standard, Custom or Module Replacement), click the "Read SYNC" button to verify the current APIM , Vehicle Interface Processor (VIP) and Consumer Interface Processor (CIP) software levels. The versions are compared to a online database. After the comparison, the available software is displayed.
5. When carrying out the programming procedures, follow the scan tool on-screen directions. Select the "Program SYNC" button to begin the APIM programming process.
6. Follow the scan tool on-screen directions for APIM programming.

1. After programming is complete the scan tool displays "Programming has been completed successfully."