Definition of Terms
The following are definitions of configuration terms
Module Reprogramming
Module reprogramming (also referred to as flashing) is a scan tool process which updates the strategy/calibration in a module. Reprogramming a module with the same level of software will not improve module operation or repair a hardware failure. Module reprogramming is automatically carried out during PMI when a later strategy/calibration is available.
Note. Module reprogramming should be limited to circumstances where a published TSB procedure recommends doing so.
Note. A module cannot communicate with other modules on the communication network while being reprogrammed. Clear any network communication DTCs which may have been set in other modules during the reprogramming process.
Accessory Protocol Interface Module (APIM) Programming
Accessory Protocol Interface Module (APIM) programming is a process that updates the APIM Consumer Interface Processor (CIP) and Vehicle Interface Processor (VIP) software. The VIP programming updates the calibration files in the portion of the APIM that interfaces with the Controller Area Network (CAN). The CIP programming updates calibration files in the portion of the APIM that interfaces with mobile phones and other customer devices.
APIM programming uses the Vehicle Communication Module (VCM) to read and program the VIP software through the Data Link Connector (DLC). A web-based On-Line Automotive Service Information System (OASIS) application is used to read and program the CIP software via a Universal Serial Bus (USB) cable between the scan tool and the vehicle USB port. Both the VCM and the OASIS application must be running on the scan tool during APIM programming. To carry out APIM programming, refer to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) PROGRAMMING in this service information.
Programmable Parameters
Programmable parameters are customer preference items that may be modified by the dealer via the scan tool or in some cases, modified by the customer following a procedure listed in the Owner's Literature. While many configuration options may exist for a module, only a few of these options are programmable parameters.
Module Address
A unique module address is assigned to each module on the network for identification.
As-Built Data
As-Built data is a VIN -specific module configuration record. During vehicle build, the configuration from all modules is downloaded and stored in the As-Built database. As-Built data does not reflect customer preference items that have been changed from the default state. These items need to be changed using programmable parameters after the module is configured.
Note. It is not necessary to obtain As-Built data unless directed to do so by the scan tool. This data may be accessed from the technician service publication website.
The following chart lists As-Built data addresses and describes specific module configuration information
Module Configuration and Parameter Chart
| Module | Module Address | Requires PMI | Reprogram/Flash Capable | Requires Adaptive Learning or Calibration | Available Programmable Parameters |
|---|---|---|---|---|---|
| ABS module | 760 | Yes | Yes | No | None |
| Accessory Protocol Interface Module (APIM) | 7D0 | Yes | Yes | No | None |
| Audio Control Module (ACM) | 727 | Yes | Yes | No | External Satellite Digital Audio Receiver System (SDARS) module |
| Body Control Module B (BCM-B) | 7B7 | Yes | Yes | No | None |
| Front Controls Interface Module (FCIM) | 7A7 | No | Yes | No | None |
| Front Display Interface Module (FDIM) | 7A6 | Yes | Yes | No | None |
| Global Positioning System Module (GPSM) | 701 | No | Yes | No | None |
| HVAC module | 733 | No | Yes | No | None |
| Instrument Panel Cluster (IPC) | 720 | Yes | Yes | No | Default language |
| Occupant Classification System Module (OCSM) | 765 | No | Yes | Seat weight sensor rezero | None |
| PCM | 7E0 | Yes | Yes | Adaptive airflow Idle speed Refueling event Fuel trim | Axle ratio Speed control Tire size |
| Power Steering Control Module (PSCM) | 730 | Yes | Yes | No | None |
| Restraints Control Module (RCM) | 737 | Yes | Yes | Seat weight sensor rezero | Emergency call (eCall) present |
| Smart Junction Box (SJB) | 726 | Yes | Yes | No | Locking light feedback Remote panic Security horn alarm Tire placard pressure |
MODULE CONFIGURATION AND PARAMETER CHART