Inspection and Verification
This part provides step-by-step module configuration procedures. Carry out the Programmable Module Installation (PMI) procedures in this part when another workshop article directs to carry out configuration or when DTCs from the below list are present
DTC Chart
Note. Some modules on this vehicle utilize a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
| DTC | Description | Source | Action |
|---|---|---|---|
| B2477 | Module Configuration Failure | ABS module (without Hybrid) Audio Control Module (ACM) (without navigation) HVAC module Front Display Interface Module (FDIM) Instrument Cluster (IC) Parking Aid Module (PAM) Power Steering Control Module (PSCM) Satellite Digital Audio Receiver System (SDARS) module Smart Junction Box (SJB) (without Hybrid) | CARRY OUT Programmable Module Installation (PMI). REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| B2477 | Module Configuration Failure | Accessory Protocol Interface Module (APIM) | CARRY OUT APIM programming. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) PROGRAMMING . |
| B2900 | VIN Mismatch | ABS module (without Hybrid) SJB | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| P0602 | Powertrain Control Module Programming Error | PCM | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| P0605 | Internal Control Module Read Only Memory (ROM) Error | PCM | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| P1635 | Tire/Axle Out of Acceptable Range | PCM | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| P1639 | Vehicle ID Block Corrupted, Not Programmed | PCM | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U0300 | Internal Control Module Software Incompatibility | HVAC module PCM RCM Battery Control Module (BCM) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U0300:00 | Internal Control Module Software Incompatibility: No Sub Type Information | Restraints Control Module (RCM) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U0300:51 | Internal Control Module Software Incompatibility: Not Programmed | ABS module (Hybrid) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | ACM (with navigation) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U2050 | No Application Present | ABS module (without Hybrid) ACM (without navigation audio) HVAC module 4X4 control module Front Controls Interface Module (FCIM) FDIM IC Occupant Classification System Module (OCSM) SDARS module SJB BCM | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U2050 | No Application Present | APIM | CARRY OUT APIM programming. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) PROGRAMMING . |
| U2051 | One or More Calibration Files Missing/Corrupt | ACM (without navigation) HVAC module 4X4 control module FCIM FDIM OCSM | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | ACM (with navigation) ABS module (Hybrid) RCM | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | Accessory Protocol Interface Module (APIM) | CARRY OUT APIM programming. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) PROGRAMMING . |
| U2100:41 | Initial Configuration Not Complete: General Checksum Failure | ABS module (Hybrid) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U2100:56 | Initial Configuration Not Complete: Invalid/Incompatible Configuration | ABS module (Hybrid) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | ACM (with navigation) | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | APIM | CARRY OUT APIM programming. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) PROGRAMMING . |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | RCM | INSTALL a new RCM. REFER to SUPPLEMENTAL RESTRAINT SYSTEM . CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U3000:46 | Control Module: Calibration/Parameter Memory Failure | RCM | INSTALL a new RCM. REFER to SUPPLEMENTAL RESTRAINT SYSTEM . CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
| U3002:62 | Vehicle Identification Number: Signal Compare Failure | ABS module (Hybrid) RCM | CARRY OUT PMI. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . |
DTC CHART
Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is Available
Note. Following module installation, some modules require a separate learning procedure be carried out. For adaptive learning and calibration instructions, refer to the specific module removal and installation procedures.
- Connect the IDS and identify the vehicle as normal.
- From the Toolbox icon, select Module Programming and press the check mark.
- Select Programmable Module Installation.
- Select the module that is being replaced.
- Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
- Install the new module and press the check mark.
- Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
- The IDS downloads the data into the new module and displays Module Configuration Complete.
- Test module for correct operation.
Programmable Module Installation (PMI) Using the Integrated Diagnostic System (IDS) When the Original Module is NOT Available
Note. Following module installation, some modules require a separate learning procedure be carried out. For adaptive learning and calibration instructions, refer to the specific module removal and installation procedures.
- Install the new module.
- Connect the IDS and identify the vehicle as normal.
- From the Toolbox icon, select Module Programming and press the check mark.
- Select Programmable Module Installation.
- Select the module that was replaced.
- Follow the on-screen instructions, turn the ignition key to the OFF position, and press the check mark.
- Follow the on-screen instructions, turn the ignition key to the ON position, and press the check mark.
- If the data is not available, the IDS displays a screen stating to contact the As-Built Data Center. Retrieve the data from the technician service publication website at this time and press the check mark.
- Enter the module data and press the check mark.
- The IDS downloads the data into the new module and displays Module Configuration Complete.
- Test module for correct operation.
Accessory Protocol Interface Module (APIM) Programming Using the Integrated Diagnostic System (IDS)
Note. If a new Accessory Protocol Interface Module (APIM) is being installed, install the new APIM before carrying out the following procedure. For additional information, refer to INFORMATION AND ENTERTAINMENT SYSTEMS .
- Turn the Audio Control Module (ACM) on.
- Connect the scan tool to the Data Link Connector (DLC).
- Connect one end of the Universal Serial Bus (USB) male-A to male-A cable to the scan tool.
- Connect the other end of the USB male-A to male-A cable to the vehicle USB port.
- From the technician service publication website, run On-Line Automotive Service Information System (OASIS) using Quick Start or by manually entering the Vehicle Identification Number (VIN).
- From the OASIS tab, select the "Sync/APIM" bullet.
- Select the "Read APIM" button to verify the current APIM Vehicle Interface Processor (VIP) and Consumer Interface Processor (CIP) software levels.
- Select the desired software level from the list of available software for programming then select the "Program APIM" button to begin the APIM programming process. Enter the APIM As-Built data if prompted. When only the CIP is being programmed, select cancel when prompted whether or not to program the VIP. When the VIP is programmed, the CIP will be programmed automatically.
- The Sync/APIM application downloads the software into the APIM and displays "Programming has been completed successfully".
- Test the audio system for correct operation.