FLUID CAPACITIES
| Application | Refill - Qts. (L) | Dry Fill - Qts. (L) |
|---|
| Dakota, Durango & Grand Cherokee |
| 42RE, 44RE & 46RE | (2) 4.0 (3.8) | (3) 9.6-10.0 (9.1-9.5) |
| Ram Pickup |
| 42RE | (2) 4.0 (3.8) | (3) 8.5-11.0 (8.0-10.4) |
| 46RE | (2) 4.0 (3.8) | (3) 9.5-11.6 (9.0-11.0) |
| 47RE | (2) 4.0 (3.8) | (3) 14.8-16.9 (14.0-16.0) |
| Ram Van & Ram Wagon |
| 46RE | (2) 4.0 (3.8) | (3) 9.6-9.8 (9.1-9.3) |
| (1) Approximate quantities listed. (2) Add fluid until level is at MIN mark on dipstick. Start engine and allow it to idle. With brakes applied, shift transmission through all gear ranges and return to Neutral. Add additional fluid to bring level to MIN mark on dipstick. Recheck fluid level with transmission at normal operating temperature. Adjust fluid level to MAX mark on dipstick. (3) Quantity may vary with type of oil cooler and oil cooler lines. |
| (1) | Approximate quantities listed. |
| (2) | Add fluid until level is at MIN mark on dipstick. Start engine and allow it to idle. With brakes applied, shift transmission through all gear ranges and return to Neutral. Add additional fluid to bring level to MIN mark on dipstick. Recheck fluid level with transmission at normal operating temperature. Adjust fluid level to MAX mark on dipstick. |
| (3) | Quantity may vary with type of oil cooler and oil cooler lines. |
TRANSMISSION FLUID CAPACITIES (1)
| Application | Pts. (L) |
|---|
| Dakota & Durango |
| NV231, NV231-HD & NV233 | 2.5 (1.2) |
| NV242 & NV244 | 3.0 (1.4) |
| Grand Cherokee |
| NV242 | 3.0 (1.4) |
| Ram Pickup |
| NV231-HD | 2.5 (1.2) |
| NV241 | 5.7 (2.7) |
| NV241-HD |
| With PTO Adapter | 4.9 (2.3) |
| Without PTO Adapter | 3.5 (1.7) |
| PTO Adapter | 2.1 (1.0) |
| (1) Approximate quantities listed. |
| (1) | Approximate quantities listed. |
TRANSFER CASE FLUID CAPACITIES (1)
- Raise and support vehicle. Loosen oil pan bolts, allowing fluid to drain. Remove oil pan bolts, oil pan and gasket. Remove oil filter bolts and oil filter from valve body.
- Adjust kickdown and low-reverse bands, if necessary. See «KICKDOWN BAND»(ref-97193-S38717479652001042600000) and «LOW-REVERSE BAND»(ref-97193-S13125688672001042600000) under ADJUSTMENTS.
- Clean oil pan, magnet and all sealing surfaces. Install NEW oil filter. Install and tighten oil filter screws to specification. See «TORQUE SPECIFICATIONS»(ref-97193-S25271172682001042600000) . Using NEW gasket, install oil pan. Install and tighten oil pan bolts to specification.
- Add appropriate fluid until level is at MIN mark on dipstick. See «RECOMMENDED FLUIDS»(ref-97193-S13253460092001042600000) . Start engine and allow it to idle. With brakes applied, shift transmission through all gear ranges and return to Neutral.
- Add additional fluid to bring level to MIN mark on dipstick. Recheck fluid level with transmission at normal operating temperature. Adjust fluid level to MAX mark on dipstick. See «CHECKING FLUID LEVELS»(ref-97193-S30291707142001042600000) . DO NOT overfill.
TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) |
|---|
| Adapter Housing-To-Transmission Case Bolt | 24 (33) |
| Crossmember Bolt | 50 (68) |
| Driveshaft "U" Joint Clamp Bolt | 22 (30) |
| Driveshaft Companion Flange Bolt | 80 (108) |
| Extension Housing-To-Rear Mount Bolt | 50 (68) |
| Extension Housing-To-Transmission Case Bolt | 32 (43) |
| Kickdown Band Adjusting Screw Lock Nut | 30 (41) |
| Low-Reverse Band Adjusting Screw Lock Nut | 25 (34) |
| Oil Pan Bolt | 13 (17) |
| Output Speed Sensor | 20 (27) |
| Park/Neutral Position Switch | 25 (34) |
| Transfer Case Drain & Fill Plugs |
| NV231, NV233 & NV244 | 15-25 (20-34) |
| NV231-HD, NV241 & NV241-HD | 30-33 (40-45) |
| NV242-HD | 15-18 (20-25) |
| INCH Lbs. (N.m) |
| Governor Body-To-Transfer Plate Bolt | 35 (4.0) |
| Oil Filter Screw | 35 (4.0) |
| Transfer Case Linkage Adjusting Lock Bolt | 89 (10.0) |
| Valve Body Screw | 35 (4.0) |
| Valve Body-To-Transmission Case Bolt | 106 (12.0) |
