Programming and Setup - All Systems: Removal & Installation Cadillac SRX II facelift

Replace and Program Active Safety Control Module or Reprogram Active Safety Control Module

To program a replacement or an existing active safety control module, perform the following procedure

1. Access the Service Programming System (SPS) and follow the on-screen instructions.
2. On the SPS Supported Controllers screen, select Active Safety Control Module - Programming and follow the on-screen instructions.
3. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.

Replace and Program Control Module or Reprogram Control Module

To program a replacement or an existing control module, perform the following procedure

1. Install the EL-49642 SPS Programming Support Tool.
2. Access the Service Programming System (SPS) and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select T3 Audio Amplifier - Programming and follow the on-screen instructions.
4. At the end of programming, choose the "Clear DTCs" function on the SPS screen.

Replace and Program Control Module

To program a replacement K9 Body Control Module (BCM), perform the following procedure

1. Install EL-49642 SPS programming support tool.
2. Access the Service Programming System (SPS) and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select K9 Body Control Module - Configuration and follow the on-screen instructions (if applicable).
4. On the SPS Supported Controllers screen, select K9 Body Control Module - Programming and follow the on-screen instructions.
5. Perform the following for the appropriate ignition type prior to proceeding with the next step: Key Ignition System: Key in the ignition and any additional keys must be away from the vehicle at least 3 m. Push Button Start System: Keyless entry transmitter must be in the programming pocket. Refer to the owner manual for the exact pocket location. All additional transmitters must be away from the vehicle at least 3 m.
6. On the SPS Supported Controllers screen, select IMMO Immobilizer Learn - Setup. On the next screen, select Body Control Module IMMO Learn with Existing Transponder or Remote Key and follow the on-screen instructions. When Immobilizer Learn is complete, press the Unlock button on the keyless entry transmitter to allow the keyless entry transmitter to exit the Immobilizer Learn mode.
7. On the SPS Supported Controllers screen, select K9 Body Control Module - Setup and follow the on-screen instructions.
8. Check the driver information center display for additional messages regarding further calibration instructions. If there are no additional driver information center instructions present, programming is complete.
9. At the end of programming, choose the "Clear DTCs" function on the SPS screen.
10. If ABS, Traction Control and/or Stabilitrak indicators are ON and DTC C0161 is set in the K17 Electronic Brake Control Module after performing BCM programming and setup, do the following: Disconnect the scan tool from the X84 Data Link Connector. Ignition OFF, all access doors closed, all vehicle systems OFF, and all keys at least 3 m (9.8 ft) away from the vehicle. It may take up to 2 min to power down. Ignition ON, verify DTC C0161 is in history. If not, repeat the above step to make sure the vehicle is in sleep mode. Use the scan tool to clear the DTCs.

To program a replacement transmission control module (TCM), perform the following procedure

1. Install EL-49642 SPS Programming Support Tool.
2. Access the Service Programming System (SPS) and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select Transmission Control Module - Programming and follow the on-screen instructions.
4. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.
5. With a scan tool, perform the Reset Transmission Adapts. Refer to «Reset Transmission Adapts»(ref-644767-S08017244932014072300000) .

Replace and Program Electronic Brake Control Module or Reprogram Electronic Brake Control Module

To program a replacement or an existing Electronic Brake Control Module, perform the following procedure

1. Access the Service Programming System (SPS) and follow the on-screen instructions.
2. On the SPS Supported Controllers screen, select Electronic Brake Control Module - Programming and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select Electronic Brake Control Module - Setup and follow the on-screen instructions.
4. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.

Replace and Program ECU or Reprogram ECU

To program a replacement or an existing ECU, perform the following procedure

1. Install EL-49642 SPS programming support tool.
2. Access the Service Programming System (SPS) and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select K43 Park Brake Control Module - Programming and follow the on-screen instructions.
4. On the SPS Supported Controllers screen, select K43 Park Brake Control Module - Setup (OR K43 Park Brake Control Module - Configuration and Setup) and follow the on-screen instructions.
5. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.
6. With a scan tool, perform the Parking Brake Cable Adjuster Enabling procedure. Refer to «Parking Brake Cable Adjuster Enabling»(ref-644737-S23082176332014072300000) .

To program a replacement K20 Engine Control Module (ECM), perform the following procedure

1. Install EL-49642 SPS programming support tool.
2. Access the Service Programming System (SPS) and follow the on-screen instructions.
3. Before removing the old control module, perform the SPS function Prepare Control Module for Removal, if available. NOTE: The Prepare Control Module for Removal function can only be performed when communication with the old control module is still possible.
4. Replace the ECM.
5. Perform the SPS function K20 Engine Control Module - Programming and follow the on-screen instructions.
6. Clear the DTCs after completing the Programming procedure.
7. Perform the SPS function Immobilizer Learn and follow the on-screen instructions. Refer to «Immobilizer System Component Programming»(ref-644723-S20010368912014072300000) .
8. Perform the SPS function K20 Engine Control Module - Configuration & Setup and follow the on-screen instructions.
9. Clear DTCs after completing the Configuration & Setup procedure.

To program a replacement control module, perform the following procedure

1. Access the Service Programming System (SPS) and follow the on-screen instructions.
2. On the SPS Supported Controllers screen, select Parking Assist Control Module - Programming and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select Parking Assist Control Module - Setup and follow the on-screen instructions.
4. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.

Replace and Program Frontview Camera Module or Reprogram Frontview Camera Module (without UGN)

To program a replacement or an existing Front View Camera Module, perform the following procedure

1. Access the Service Programming System (SPS) and follow the on-screen instructions.
2. On the SPS Supported Controllers screen, select K109 Frontview Camera Module - Programming and follow the on-screen instructions.
3. At the end of programming, choose the "Clear DTCs" function on the SPS screen.
4. Following K109 Frontview Camera Module replacement and reprogramming, the module must be calibrated. Refer to «Front View Camera Module Calibration»(ref-644761-S31498063962014072300000) .

Replace and Program Frontview Camera Module or Reprogram Frontview Camera Module (with UGN)

To program a replacement or an existing Front View Camera Module, perform the following procedure

1. Access the Service Programming System (SPS) and follow the on-screen instructions.
2. On the SPS Supported Controllers screen, select K109 Frontview Camera Module - Programming and follow the on-screen instructions.
3. If reprogramming an existing module that was previously calibrated, calibration is not required. The module retains its calibration settings during reprogramming. If a new module was programmed the module alignment must be calibrated. Using a scantool, initiate the learn procedure for Frontview Camera Module. The scantool must remain connected and on the calibration screen during the entire process. Refer to «Front View Camera Module Calibration»(ref-644761-S31498063962014072300000) .

This ECU does not require SPS programming but does require the following setup procedures after a new ECU is installed

The customer must learn the device they wish to control. This must be done at the device (garage door opener, electric gate, etc.) and cannot be performed at a dealership. Refer to the vehicle owner's manual for programming instructions.

This control module does not require SPS programming but does require the following setup procedures after a new control module is installed

To program a replacement or an existing control module, perform the following procedure

1. Install a scan tool.
2. Clear all DTC's before proceeding.
3. Select Module Diagnostics.
4. Select Headlamp Control Module.
5. Select Configuration/Reset Functions.
6. Select Headlamp Leveling Sensor Learn and follow the on-screen instructions.

To program a replacement control module, perform the following procedure

1. Install the EL-49642 SPS Programming Support Tool.
2. Access the Service Programming System (SPS) and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select K74 Human Machine Interface Control Module - Programming and follow the on-screen instructions.
4. Connect a USB drive to the computer.
5. Access the Service Programming System (SPS) and follow the on-screen instructions.
6. On the SPS Supported Controllers screen, select K74 Human Machine Interface Control Module - USB File Transfer. NOTE: If there are no files available for USB transfer via SPS, proceed to step 12. All existing files on the USB drive will be erased when the new files are copied.
7. Upon completion of the file transfer, remove the USB drive from the computer.
8. Ignition ON, infotainment system ON.
9. Connect the USB drive to the USB port in the vehicle.
10. The infotainment system will recognize that update files are available. Follow the infotainment display on-screen instructions and select Update when prompted. Programming will take several minutes.
11. Upon completion of programming, remove the USB drive. Follow the infotainment display on-screen instructions.
12. At the end of programming, choose the "Clear DTCs" function on the SPS screen.
13. Ignition OFF, Retained Accessory Power (RAP) OFF, remove the key fob from range of the vehicle, and let the vehicle sit for five minutes. Retest system operation to verify the repair.

To program a replacement or an existing control module, perform the following procedure

1. Access the Service Programming System (SPS) and follow the on-screen instructions.
2. On the SPS Supported Controllers screen, select HVAC Control Module - Programming and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select HVAC Control Module - Setup, if applicable, and follow the on-screen instructions.
4. On the SPS Supported Controllers screen, select HVAC Control Module - Configuration, if applicable, and follow the on-screen instructions.
5. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.
6. With a scan tool, perform the Actuator Recalibration Function. Refer to «Actuator Recalibration»(ref-644765-S14650276342014072300000) .

This ECU does not require SPS programming or any setup procedures.

Replace and Program ECU

To program a replacement or an existing ECU, perform the following procedure

1. Install EL-49642 SPS programming support tool.
2. Access the Service Programming System (SPS) and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select Instrument Cluster - USB File Transfer and follow the on-screen instructions.
4. On the SPS Supported Controllers screen, select Instrument Cluster - Programming and follow the on-screen instructions.
5. On the SPS Supported Controllers screen, select Instrument Cluster - Setup and Configuration and follow the on-screen instructions.
6. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.

To program a replacement or an existing ECU, perform the following procedure

1. Install EL-49642 SPS programming support tool.
2. Access the Service Programming System (SPS) and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select Keyless Entry Control Module - Programming and follow the on-screen instructions.
4. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.

To program a replacement control module, perform the following procedure

1. Install EL-49642 SPS Programming Support Tool.
2. Access the Service Programming System (SPS) and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select Liftgate Control Module - Programming and follow the on-screen instructions.
4. On the SPS Supported Controllers screen, select Liftgate Control Module - Setup and follow the on-screen instructions.
5. On the SPS Supported Controllers screen, select Liftgate Control Module - Configuration and follow the on-screen instructions.
6. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.
7. With a scan tool, perform the Garage Height Calibration. Refer to «Liftgate Calibration»(ref-644707-S40164003732014072300000)

Replace and Program Radar Sensor Module - Long Range or Reprogram Radar Sensor Module - Long Range

To program a replacement or an existing Long Range Radar Sensor Module, perform the following procedure

1. Access the Service Programming System (SPS) and follow the on-screen instructions.
2. On the SPS Supported Controllers screen, select B233B Radar Sensor Module - Long Range - Programming and follow the on-screen instructions.
3. Ignition OFF and all vehicle systems OFF. It may take up to 2 minutes for all vehicle systems to power down.
4. Following programming, the module alignment must be calibrated. Refer to «Radar Sensor Module - Long Range Calibration»(ref-644761-S36566531652014072300000) .

To program a replacement or an existing control module, perform the following procedure

1. Install EL-49642 SPS Programming Support Tool.
2. Access the Service Programming System (SPS) and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select MSM Memory Seat Module - Programming and follow the on-screen instructions.
4. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.

After the memory seat module programming has been completed and if the vehicle is equipped with adjustable pedals, adjustable pedal calibration must be performed. Refer to Adjustable Pedal System Calibration .

Mobile Telephone Control Module Replacement and/or Programming

If the mobile telephone control module needs to be replaced and/or reprogrammed, the following procedures must be performed

1. Connect a scan tool to the vehicle and access SPS. Refer to «Service Programming System (SPS)»(ref-644727-S17604612672014072300000) .
2. Perform the SPS function Mobile Telephone Control Module Programming and follow the on-screen instructions.
3. Perform the SPS function Onstar Activation and follow the on-screen instructions.
4. Clear DTCs after completing the programming procedure.

Multi-Axis Acceleration Sensor Module Programming and Setup

Note. The Multi-axis Acceleration Sensor is also known as the Inertia Sensor Module (IMU) in SPS. The sensor must be configured using SPS before the vehicle yaw sensor learn is performed.

The multi-axis acceleration sensor module must be configured.

Ensure that the following conditions exist in order to prepare for multi-axis acceleration sensor module for configuration

1. The battery is fully charged.
2. The MDI data link connectors are secure.
3. The scan tool is loaded with the most current software version.
4. All disconnected modules and devices are reconnected securely.
5. This entire procedure has been reviewed before proceeding.

Multi-Axis Acceleration Sensor Module Configuration

A replacement multi-axis acceleration sensor module, requires the following procedure

1. With a scan tool, access the Service Programming System (SPS) and follow the on-screen instructions. Refer to «Service Programming System (SPS)»(ref-644727-S17604612672014072300000) .
2. On the SPS Supported Controllers screen, select IMU Inertia Sensor Module - Configuration and follow the on-screen instructions.
3. With a scan tool, clear all DTC's from all modules.
4. Calibrate the yaw sensor using the scan tool. Refer to «Vehicle Yaw Sensor Learn»(ref-644739-S10199383822014072300000) .

To program a replacement or an existing control module, perform the following procedure

Without Rear Seat Video Entertainment System

This control module does not require SPS programming or any setup procedures.

With Rear Seat Video Entertainment System

1. Install the EL-49642 SPS Programming Support Tool.
2. Connect a USB drive to the computer.
3. Access the Service Programming System (SPS) and follow the on-screen instructions.
4. On the SPS Supported Controllers screen, select Media Disc Player - USB File Transfer and follow the on-screen instructions. NOTE: If there are no files available for USB transfer via SPS, proceed to step 11. All existing files on the USB drive will be erased when the new files are copied.
5. Upon completion of the file transfer, remove the USB drive from the computer.
6. Ignition ON, infotainment system ON.
7. Connect the USB drive to the rear seat USB port in the vehicle.
8. The infotainment system will recognize that update files are available. Follow the infotainment display on-screen instructions and select Update when prompted. Programming will take several minutes.
9. Upon completion of programming, remove the USB drive. Follow the infotainment display on-screen instructions.
10. On the SPS Supported Controllers screen, select Media Disc Player - Programming and follow the on-screen instructions.
11. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.

To program a replacement or an existing control module, perform the following procedure

1. Access the Service Programming System (SPS) and follow the on-screen instructions.
2. On the SPS Supported Controllers screen, select B233 Radar Sensor Module - Short Range - Programming and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select B233 Radar Sensor Module - Short Range - Setup and follow the on-screen instructions.
4. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.
5. Following programming, the module ID must be programmed. With a scan tool, perform the Radar Sensor Module - Short Range learn procedure.

Replace Control Module

The replacement control module is fully programmed by the supplier and does not require SPS programming or any setup procedures.

To program a replacement or an existing control module, perform the following procedure

1. Install EL-49642 SPS Programming Support Tool.
2. Access the Service Programming System (SPS) and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select A11 Radio - Programming and follow the on-screen instructions.
4. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.

To program a replacement or an existing ECU, perform the following procedure

1. Install EL-49642 SPS programming support tool .
2. Access the Service Programming System (SPS) and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select Rear Differential Clutch Control Module- Programming and follow the on-screen instructions.
4. On the SPS Supported Controllers screen, select Rear Differential Clutch Control Module- Configuration and follow the on-screen instructions.
5. At the end of programming, choose the "Clear DTCs" function on the SPS screen.

This ECU does not require SPS programming or any setup procedures.

To program a replacement control module, perform the following procedure

1. Access the Service Programming System (SPS) and follow the on-screen instructions.
2. On the SPS Supported Controllers screen, select M101 Seat Belt Retractor Motor Module and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select M101 Seat Belt Retractor Motor Module - Setup or Configuration and Setup and follow the on-screen instructions.
4. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.

To program a replacement or an existing ECU, perform the following procedure

1. Access the Service Programming System (SPS) and follow the on-screen instructions.
2. On the SPS Supported Controllers screen, select B218R Right Side Object Sensor Module or B218L Left Side Object Detection - Programming and follow the on-screen instructions.
3. At the end of programming, choose the "Clear DTCs" function on the SPS screen.

To program a replacement or an existing B218L Side Object Sensor Module - Left, perform the following procedure

1. Access the Service Programming System (SPS) and follow the on-screen instructions.
2. On the SPS Supported Controllers screen, select B218L Side Object Sensor Module - Left - Programming and follow the on-screen instructions.
3. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.

Replace and Program Steering Column Lock Control Module or Reprogram Steering Column Lock Control Module

To program a replacement steering column lock control module or reprogram an existing steering column lock control module, perform the following procedure

1. Install EL-49642 SPS programming support tool.
2. Ignition ON.
3. Access the Service Programming System (SPS) and follow the on-screen instructions.
4. On the SPS Supported Controllers screen, select Steering Column Lock Control Module - Programming and follow the on-screen instructions.
5. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.

Communication Interface Module Replacement

Note. It is critical to use the service replacement telematics communication interface control module only in the vehicle for which it was ordered. Failure to perform the following procedures will result in a red LED, DTC(s) being set, and limited or incomplete OnStar® services. An OnStar® button press to the OnStar® call center is not required to complete the procedure. It may take up to 24 hours for OnStar® service to become fully activated after performing the procedures. Perform the following procedure only once. Repeat attempts of the procedure may result in a delay of the activation process. To fully activate an OnStar® module, both the setup and activation request procedures must be completed on all vehicles with and without an active OnStar® subscription to insure the unit has been setup properly for the vehicle it has been installed into and also to update the OnStar® with the correct unit information. To initialize the Turn-by-Turn feature, the vehicle must first be driven In open sky condition at speeds greater than 10 mph (16 kph) or more for a minimum of 5 miles (8 km) , and perform at least 2 left and 2 right 90 degree turns coming to complete stops prior to each turn. On vehicles up fitted with TTY capabilities, it is necessary to perform a power cycle of the OnStar® Interface Module (OTIM), and toggle the TTY mode after completing the telematics communication interface control module installation and setup procedures.

1. Install EL-49642 SPS programming support tool .
2. Access the Service Programming System (SPS) and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select ONSU Onstar® Module Setup and Service Activation and follow the on-screen instructions.
4. At the end of programming, choose the "Clear All DTCs" function on the SPS screen.
5. The default language for the new telematics communication interface control module is English. To change to an alternate language, access the scan tool.
6. Inform the customer that it may take up to 24 hours for the OnStar® service to become fully activated.