64 00 000 Information on using cleaning agent/paints (personal protection equipment)
| WARNING | Use of cleaning agents/paints not compliant with instructions can cause serious injuries or burns! Handling cleaning agents/paints can trigger allergic skin and respiratory reactions! |
| IMPORTANT | Observe following instructions: Store cleaning agents/paints only in a secure cabinet. Keep cleaning agents/paints away from naked flames and other sources of ignition. Protect cleaning agents/paints from high temperatures and direct sunlight. Always keep an eye bath on hand, change the water regularly (once a month). |
| IMPORTANT | Observe following instructions before use: Manufacturer's instructions (on container/packaging) Hazard warnings (on container/packaging) Manufacturer's instructions on package insert Material safety data sheet of manufacturer Product information in EPC National market regulations |
| IMPORTANT | Observe following instructions during use: Do not eat, drink or smoke while working with these products. Avoid direct contact with skin and eyes. Wear personal protective clothing/equipment. Ensure that all enclosed areas are well ventilated or extract fumes directly. Immediately change working clothes soiled with cleaning agent/paint. After finishing work, wash your hands and apply protective skin cream. |
| IMPORTANT | Follow hazard warnings and wear personal protection equipment! |
First Aid
- If product comes in contact with eyes, immediately flush with running water for about 10 - 15 minutes. Seek the advice of eye specialist.
- In the event of skin contact and where applicable an allergic skin reaction, clean the affected areas immediately with soap and water and then apply silicone-free skin cream. Seek advice of physician.
- If an adhesive product is swallowed, rinse mouth/parts of mouth thoroughly with running water. Drink 1-2 glasses of water. Do not induce vomiting. Consult a doctor.
- After inhaling vapors ensure ample supply of fresh air. Keep calm, keep respiratory tracks clear and call doctor.
Recycling
Dispose of cleaning agents/paints in a professional manner!
Observe national/country-specific disposal regulations.
35 11 000 Removing and installing complete bearing block for foot pedal
Necessary preliminary tasks
- Remove «CLUTCH PEDAL»(/bmw/m3/e90-2007-2013/remont/mechanical-hydraulic/#pedals-repair-e90__35-31-000-removing-and-installing)
Release screws (1) and gently press clutch master cylinder (2) to one side.
Installation
Line remains connected.
Replace self-locking nuts.
Tightening torque 21 52 4AZ .
Scheme 278
Disconnect plug connection (1).
Remove locking clip (2) and pull out pin.
Unscrew nut (3).
Release nuts (4) and gently swivel bearing block to left and remove.
Installation
Tighten nuts (4) before nut (3).
Replace self-locking nuts.
Tightening torque 35 11 1AZ .
Scheme 279
35 21 041 Replacing spring for brake pedal
Necessary preliminary tasks
- Remove «TRIM PANEL FOR PEDAL ASSEMBLY»(/bmw/m3/e90-2007-2013/remont/door-locks-anti-theft-systems/#body-equipment-repair-e90__51-45-185-removing-and-installingreplacing) .
Disconnect return spring (1).
Scheme 280
35 31 041 Replacing spring for clutch pedal
Necessary preliminary tasks
- Remove «TRIM PANEL FOR PEDAL ASSEMBLY»(/bmw/m3/e90-2007-2013/remont/door-locks-anti-theft-systems/#body-equipment-repair-e90__51-45-185-removing-and-installingreplacing) .
Disconnect return spring (1).
Scheme 281
Necessary preliminary tasks
- Remove «TRIM PANEL FOR PEDAL ASSEMBLY»(/bmw/m3/e90-2007-2013/remont/door-locks-anti-theft-systems/#body-equipment-repair-e90__51-45-185-removing-and-installingreplacing) .
Disconnect return spring (1).
Necessary preliminary tasks
- Remove «TRIM PANEL FOR PEDAL ASSEMBLY»(/bmw/m3/e90-2007-2013/remont/door-locks-anti-theft-systems/#body-equipment-repair-e90__51-45-185-removing-and-installingreplacing) .
Disconnect return spring (1).
35 31 000 Removing and installing or replacing clutch pedal
Necessary preliminary tasks
- Remove pedal «TRIM»(/bmw/m3/e90-2007-2013/remont/door-locks-anti-theft-systems/#body-equipment-repair-e90__51-45-185-removing-and-installingreplacing) .
- If necessary, remove «OVER-CENTER HELPER SPRING»(/bmw/m3/e90-2007-2013/remont/mechanical-hydraulic/#pedals-repair-e90__35-31-050-removing-and-installingreplacing)
Disconnect return spring (1).
Press end of pin (2) together with offset pliers and press out pin.
Detach locking clip (3) and pull clutch pedal off bearing block.
Installation
Replace locking clip (3).
Locking clip (3) must be seated with both legs in the pin groove.
Scheme 282
Installation
Check bearing bushings (1) and replace if necessary.
Lightly grease bearing bushings (1).
Scheme 283
35 31 050 Removing and installing/replacing over-center helper spring
Necessary preliminary tasks
- Remove «PEDAL TRIM»(/bmw/m3/e90-2007-2013/remont/door-locks-anti-theft-systems/#body-equipment-repair-e90__51-45-185-removing-and-installingreplacing) .
Press end of pin (1) together with offset pliers and press out pin.
Scheme 284
Push in pin (1) fully in direction of arrow.
Scheme 285
Detach retainers (1).
Installation
Check retainers, replace if necessary.
Retainers must lie with both legs in the groove and snap audibly into place.
Slide out pin (2).
Installation
Lightly grease pin.
Remove over-center helper spring (3).
Scheme 286
There are two versions
- (A) Over-center helper spring
- (B) Reinforced over-center helper spring
Assembly of over-center helper spring
- Secure black holder (1) to clutch pedal
- Smaller coil spacing of spring (2) points to black holder (1)
- Secure grey holder (3) to bearing block
Scheme 287
Lightly grease holder and spring contact surfaces.
Installation
Secure over-center helper spring first with black holder to clutch pedal.
Gently press over-center helper spring together and secure with grey holder to bearing block.
Connect clutch pedal to clutch master cylinder.
When replacing reinforced over-center helper spring
Remove locking clamp (1).
Scheme 288
35 31 011 Replacing bearing bushes for clutch pedal
Operation is described in
Necessary preliminary tasks
- Remove «TRIM PANEL FOR PEDAL ASSEMBLY»(/bmw/m3/e90-2007-2013/remont/door-locks-anti-theft-systems/#body-equipment-repair-e90__51-45-185-removing-and-installingreplacing) .
Disconnect return spring (1).
35 40 001 Removing and installing or replacing accelerator pedal module
Take off cap.
Release screw.
Pull accelerator pedal module upwards out of fixture.
Installation
Tightening torque 35 40 1AZ .
Scheme 289
Pull off plug (1).
Remove accelerator pedal module.
Scheme 290
| IMPORTANT | Accelerator pedal module can only be replaced completely with adapter plate. |