Home ReviewsRefund
Home/Audi/S6/Audi S6 C6 (2006-2008)/Repair manual/Fuel Supply System/Adapting kick-down function after replacing throttle positi…
Contents Wiring diagrams Section: Fuel Supply System All sections

Adapting kick-down function after replacing throttle position sensor or engine control module Audi S6 C6

Fuel Supply System ~525 words

Adapting kick-down function after replacing throttle position sensor or engine control module

Note. If the throttle position sensor or engine control module is replaced in vehicles with automatic transmission, the kick-down function must be adapted.

Special tools, testers and auxiliary items required

  1. Vehicle diagnostic, testing, and information system VAS 5051 (VAS 5051 B version shown as example only)

Work procedure

  1. Vehicle Diagnosis, Testing and Information System VAS 5051 connected with Diagnostic Cable VAS 5051/5A , Vehicle Self-Diagnosis selected.
  2. No faults in DTC memory.
  3. Engine not running, ignition switched on.

Display on VAS 5051

  1. Tap "On Board Diagnostic" in selection - 1 - and activate by tapping --> button.

Display on VAS 5051

  1. Tap "01 - Engine Electronics" vehicle system in selection - 1 - and activate by tapping --> button.

Display on VAS 5051

  1. Tap "006 - Basic Setting" function in selection - 1 - and activate by pressing --> button.

Display on VAS 5051

  1. In button field - 1 - , press buttons 6 3 for "display group 063" and confirm entry by pressing Q button.
  2. Activate basic setting by pressing Activate button - A -.

Display on VAS 5051

  1. Check indication in display fields - 3 - and - 4 -.
  2. After display "Activate kick-down" appears, depress gas pedal all the way down beyond kick-down point and hold it there.
Display fieldExplanations
3Kickdown
4Operate ADP in progress Specified value: ADP OK If "ERROR" is displayed: Check DTC Memory

Note. "ERROR" could be displayed e.g. if the accelerator pedal is not immediately depressed after prompting the VAS 5051 or if the accelerator pedal is released during adaptation, even though adaptation had not been completed. Exit the function "006 - Basic setting" by pressing <-- button and perform adaptation again.

  1. End function "006 - Basic setting" by pressing <-- button.
  2. Select "022 - End output" function in selection.
  3. Turn ignition off and disconnect Data Link Connector (DLC).

See also:
• 24 - MULTIPORT FUEL INJECTION (MFI)
• 27 - STARTER, GENERATOR, CRUISE CONTROL
• 72 - SEAT - FRAMES
• 66 - EXTERIOR EQUIPMENT
• 39 FINAL DRIVE, REAR DIFFERENTIAL
• 39 - FINAL DRIVE, DIFFERENTIAL
• 42 - REAR SUSPENSION
• 26 - EXHAUST SYSTEM, EMISSION CONTROLS
• Fuel tank, emptying
• Installation position of Ground (GND) connection
• Fuel tank with attachments, removing and installing
• B - Emptying a fuel tank less than 1/4 filled
• Safety precautions
• Fuel delivery unit, removing and installing
• Evaporative emissions (EVAP) canister, removing and installing
• Fuel Level Sensor G , checking
• Fuel Level Sensor G , removing and installing
• Suction jet pump, removing and installing
• Fuel Level Sensor 2 G169 , checking
• Installing
• Fuel Pump (FP) Control Module J538 , removing and installing - Vehicles with FSI engine
• Fuel filter, removing and installing
• Installed location
• Leak Detection Pump (LDP) V144 , removing and installing
• Diagnostic leak test, performing
• Checking fuel supply and tank ventilation systems for leaks
• Checking voltage supply
• Check activation
• Accelerator pedal module with Throttle Position (TP) sensors, removing and installing
• Adapting kick-down function after replacing throttle position sensor or engine control module