| Application | Lbs. (N.m) | ||
|---|---|---|---|
| Bracket Nut | 18 (25) | ||
| Bracket Bolt With Washer | 30 (40) | ||
| Camshaft Sprocket Bolt | 52 (71) | ||
| Catalytic Converter-To-Exhaust Manifold Bolt | 18 (24) | ||
| Camshaft Bearing Cap Nut | 11 (15) | ||
| Combi Bolts | 17 (23) | ||
| Connecting Rod Bearing Cap Bolt (1) | |||
| Vertical Bolt | |||
| Step 1 | 15 (20) | ||
| Step 2 | Additional 1/2 Turn | ||
| Horizontal Bolt | 18 (24) | ||
| Coolant Fan Control Thermoswitch | 18 (25) | ||
| Crankshaft Damper Bolt | 295 (400) | ||
| Crankshaft Main Bearing Cap Bolt (2) | |||
| Step 1 | 44 (60) | ||
| Step 2 | Additional 1/2 Turn | ||
| Cylinder Head Bolt (3) | |||
| Step 1 | 44 (60) | ||
| Step 2 | Additional 1/2 Turn | ||
| EGR Valve-To-Intake Manifold Bolts | 7 (10) | ||
| Engine Mount Bolt | 33 (45) | ||
| Engine-To-Transmission Bolt | |||
| M8 Bolt | 18 (24) | ||
| M10 Bolt | 33 (45) | ||
| Flywheel Bolt | 74 (100) | ||
| Idle Air Control Valve-To-Intake Manifold Nut | 7 (10) | ||
| Impact Absorber | |||
| Bolt With Washer | 17 (23) | ||
| Nut With Washer | 17 (23) | ||
| Intake Manifold-To-Cylinder Head Bolts | 15 (20) | ||
| Oil Cooler Nut | 22 (30) | ||
| Throttle Body-To-Intake Manifold | 15 (20) | ||
| Timing Belt Tensioner Bolt | 33 (45) | ||
| Torque Converter-To-Drive Plate Bolt | 26 (35) | ||
| Washer Bolt With Washer | 17 (23) | ||
| INCH Lbs. (N.m) | |||
| Cap Bolt | 89 (10) | ||
| Bushing Nut | 89 (10) | ||
| Combi Self-Tapping Screws | 66 (7.5) | ||
| Coolant Fan Motor Bolt | 89 (10) | ||
| Crankshaft Position Sensor | 89 (10) | ||
| Crankshaft Rear Oil Seal Housing Bolt | 89 (10) | ||
| Fan Frame Bolt | 89 (10) | ||
| Guide Piece Bolt With Washer | 13 (1.5) | ||
| Hex Nut | 133 (15) | ||
| Idle Air Control Valve-To-Intake Manifold Bolts | 53 (6) | ||
| Lock Carrier Plate | 66 (7.5) | ||
| Lower Air Guide Bolt | 89 (10) | ||
| Oil Pan Bolt | 89 (10) | ||
| Oil Pump Bolt | 89 (10) | ||
| Pressure Relief Valve (Top Of Cyl. Head) (4) | |||
| With 3 Raised Dots On Valve | 89 (10) | ||
| With No Raised Dots On Valve | 48 (5) | ||
| Radiator Angle Bracket Bolt | 89 (10) | ||
| Thermostat Housing Bolts | 89 (10) | ||
| Trim Strip Bolt With Washer (Right side) | |||
| Center | 22 (2.5) | ||
| Right Side | 22 (2.5) | ||
| Union (Thermostat Housing) | 89 (10) | ||
| Upper Air Guide Bolt | 89 (10) | ||
| Valve Cover Bolt | 53-89 (6-10) | ||
| Washer Nut | 9 (1.0) | ||
| (1) Replace bolts after first use. (2) A horizontally installed bolt secures each side of crankshaft main bearings No. 2 and 3 to cylinder block. These bolts must be loose (or only finger tightened) before tightening vertical bolts. Replace bolts after first use. (3) Replace bolts after first use. Tighten in sequence. (Схема №10) (4) Apply Locking Compound (AMV 197 000 01) to valve threads. | |||
| (1) | Replace bolts after first use. |
| (2) | A horizontally installed bolt secures each side of crankshaft main bearings No. 2 and 3 to cylinder block. These bolts must be loose (or only finger tightened) before tightening vertical bolts. Replace bolts after first use. |
| (3) | Replace bolts after first use. Tighten in sequence. (Схема №10) |
| (4) | Apply Locking Compound (AMV 197 000 01) to valve threads. |
TORQUE SPECIFICATIONS