Home/Volvo/V70/Volvo V70 II рестайлинг (2004-2007)/Repair manual/Gearbox, Selector Cable, Selector Knob - Removal & Installation/Final check

Contents

Section: Gearbox, Selector Cable, Selector Knob - Removal & Installation

Installing The Gear Selector Knob

Removing the panel

Removing the top panel

Installing the lock bracket on the gear selector knob

Gear selector lever knob, replacing (B5254T4, M66 AWD; 2004)

Gear selector cables, adjusting

Preparatory Work

Preparations And Adjusting Gear Selector Cable

Installing Components

Gearbox cables, replacing

Removing center tunnel console

Preparations for installing the mechanical cables

Removing the gear selector cables

Installing the rubber grommet

Feeding in the gear selector cable from the engine compartment

Installing the center tunnel console

Installing the air cleaner (ACL) housing

Final check

General

Counter 2

Engine, Status

Outside Temperature

Counts - The Operating Cycles Since The Diagnostic Trouble Code (DTC) Was First/Last Stored

Passenger Compartment Temperature

Oil Temperature

Gear Ratios

Expected Gear Ratio

Calculated Speed Of The Signal From The Transmission Speed Sensor (Output Speed)

Speed Signal, Calculated From The Engine Speed (RPM)

Gear According To The Shift Solenoids

Gear-Shift Position Sensor

Accelerator Pedal (AP) Position

Transmission Speed Sensor, Output Speed

Transmission Speed Sensor, Input Speed

Gear-Shift Position Sensor, Position

Engine Speed (RPM)

Position Of The Gear-Shift Position Sensor ABCPA

System Voltage

Engine Coolant Temperature (ECT)

Kickdown, Status

Gear According To Solenoids

Gearbox input speed sensor, replacing (B5254T4, TF-80SC AWD; 2006-2007) (version 1)

Gearbox input speed sensor, replacing (B5254T4, TF-80SC AWD; 2006-2007) (version 2)

Gearbox, installing

Gearbox, removing (B5234T3, M56; B5244S, M56; B5244T3, M56; 2001)

Disconnecting The Battery Lead

Removing the mounting screws for the gearbox and starter motor

Removing the air baffle and splash guard under the engine

Removing The Control Arms And Track Rod (Both Sides)

Removing The Nut From The Ball Joint (Both Sides)

Removing The Screws From The Sub-Frame Support Plates (Both Sides)

Removing The Stub Axle From The Control Arm

Removing The Drive Shaft From The Stub Axle (Right-Hand Side)

Removing The Sealing Ring For The CV Joint Housing

Removing The Cap For The Drive Shaft Support Bearing

Removing The Drive Shaft

Pressing Up The Sub-Frame On The Right-Hand Side

Preparatory Work For Removing The Stub Axle On The Left-Hand Side

Lowering The Sub-Frame

Lowering The Engine And Gearbox

Removing The Collision Protection System Over The Steering Gear

Installing The Fixture On The Mobile Jack

Gearbox, removing (AW50/51 AWD; AW55-50/51SN; 2001-2007)

Removing The Coolant Hose From The Passenger Compartment Heater

Gearbox, removing (B5234T3, AW55-50/51SN; 2001-2004)

Removing Engine Compartment Components

Removing Components From The Gearbox

Removing The Gearbox Mounting Screws

Installing The Lifting Beam And Lifting Hook On The Engine Lifting Eyelet

Removing The Screw For The Cable Duct

Removing The Cross Members From The Body

Measuring The Position Of The Tie Rod In The Steering Gear

Exposing The Steering Shaft Joint

Removing Front Suspension Components (Both Sides)

Preparations When Removing Gearbox

Preparations For Lowering The Sub-Frame

Removing The Right-Hand Drive Shaft

Removing The Left-Hand Drive Shaft

Removing Bevel Gear

Removing The Rear Engine Mounting

Removing The Oil Pipe From The Gearbox

Lowering The Engine And The Gearbox

Installing The Fixture On The Mobile Jack And Gearbox

Removing All The Screws For The Gearbox And Engine

Removing The Gearbox

Gearbox, removing (AW50/51 AWD; AW55-50/51SN; 2001)

Gearbox, removing (B5254T4, M66 AWD; 2004-2007)

Gearbox, removing

Removing Splash Guards

Removing The Screws For The Cable Conduit And Ground Lead Bracket On The Sub-Frame

Removing The Nut For The Lower Ball Joint/Control Arm

Removing The Screws For The Sub-Frame Support Plates (Both Sides)

Press Up The Sub-Frame On The Right-Hand Side

Removing The Front Cross Member

Removing The Screw For The Rear Engine Pad

Preparations For Removing The Stub Axle On The Left-Hand Side

Removing The Left Drive Shaft From The Gearbox

All sections

Final check Volvo V70 II рестайлинг

Gearbox, Selector Cable, Selector Knob - Removal & Installation

Final check

Check that the gear positions are working.