Home/Volvo/V70/Volvo V70 II рестайлинг (2004-2007)/Repair manual/Brake System Components - Removal and Installation/Vacuum system, checking

Contents

Section: Brake System Components - Removal and Installation

Finishing

Install The Brake Disc

Brake pads front, replacing

Preparatory work

Installing the brake pads

Installing slide pins in the brake caliper

Brake pipe hydraulic unit / junction / front wheel, replacing

Front wheel hub, replacing

Preparation

Removing brake calipers

Removing the brake disc

Installing the hub

Installing the control arm on the ball joint

Installing the anti-roll bar link

Installing the steering arm

Installing the brake disc

Installing the drive shaft screw

Installing brake calipers

Replacing front wheel hub, Steel & Aluminium

Front wheel hub (aluminium)

Removing the drive shaft

Installing the drive shaft

Installing the ball joint

Front wheel hub (steel)

Brake discs rear, replacing

Adjusting the parking brake

Brake pads rear, replacing

Preparations

Checking the brake disc

Brake pipe rear wheel, replacing

Installing the brake pipes

Installing the active yaw control sensor

Installing the seat rail

Brake Control Module (BCM), replacing

Connecting the breakout box

Contact reel / steering wheel angle sensor, replacing

Installing the contact reel and steering wheel angle sensor

Installing the steering wheel

Installing center screw

Disconnect the battery lead

Install the control module on the ABS hydraulic modulator

Depressurize the brake system

Check the control module

Installing the ABS hydraulic modulator, continued

Finishing work

Master cylinder, replacing (left-hand drive)

Installing the master cylinder

Installing the connectors

Brake pipe master cylinder / ABS unit, replacing

Installing the brake pipe for the left-hand front wheel / ABS unit

Installing the integrated relay / fusebox

Installing the air cleaner (ACL) housing

Replacing the brake pipe for the right-hand front wheel / ABS unit

Removing the air cleaner (ACL) housing

Removing the integrated relay / fusebox

Installing the brake pipe for the right-hand front wheel / ABS unit

Master cylinder, replacing (right-hand drive)

Disconnecting the connectors

Removing the brake pipe

Removing the master cylinder

Pedal sensor power brake booster, replacing

Installing pedal position sensor

Power brake booster, replacing

Transfer the terminals and seals to the new power brake booster

Tighten the power brake booster

Install the master cylinder

Install the connections on the master cylinder

Install the steering components

Secure the sub-frame

Install the cross members

Install the passenger compartment heater

Install the splashguard under the engine

Preparations for replacing the pressure sensor on the master cylinder

Installing the pressure sensor

Checking the pressure sensors visually

Bleeding the brake system

Airing

Checking the brakes

Relay box - air cleaner (ACL) housing

Air cleaner (ACL)

Removing the battery lead

Removing the control module

Checking the control module

Installing the control module on the ABS hydraulic modulator

Installing the control module

Replacing the power brake booster (DSTC)

Preparations for removing the power brake booster

Cars with passenger compartment heaters

Preparations for removing sub-frame screws

Lower the sub-frame

Install the power brake booster with the terminals for the check valve

Lift the sub-frame

Yaw rate sensor

Replacing the yaw rate sensor (1) / lateral acceleration sensor

Checking the DSTC system

Yaw rate sensor (2)

Front seat

Checking the dynamic stability and traction control (DSTC)

For model years -2004

Steering wheel module (SWM), replacing (2005-)

Installing the steering wheel module

Programming the control module

Stop lamp switch, replacing

Ignition off

Removing soundproofing

Check the shift-lock function

Checking the brake lamp switch

Installing soundproofing

Vacuum system, checking

Install the wheel sensor

Removing the wheel sensor connector

Installing wheel sensors

Installing the wheel sensor connector

Brake shoes parking brake, replacing

Removing the brake caliper with the holder and the brake disc

Installing the brake disc and the brake caliper with the holder

Removing the OBDII bracket

Installing the parking brake pedal

Installing the relay box in the passenger compartment

Installing the OBDII bracket and soundproofing panel

Installing the soundproofing panel

Parking brake, adjusting

Removing the panel

Installing the panel

All sections

Vacuum system, checking Volvo V70 II рестайлинг

Brake System Components - Removal and Installation 1 illustration

Vacuum system, checking

For V70 and V70 XC/XC70, see «Vacuum system, checking»(ref-407152-S06090170582011070100000)

Scheme 140

Scheme 140: Switch off the ignition. Remove the wheel and wheel sensor

Scheme 140: Switch off the ignition. Remove the wheel and wheel sensor

Note. Blow clean around the sensor using compressed air before removing.

Remove the sensor mounting screw. Pull out the sensor.

Remove the electrical cables from the brackets.

Remove the clips from the electrical cables.

Separate the connector. Remove the sensor.