Fault-tracing information
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
Replacing the component
The control module has registered an internal fault. Try a new control module.
Note. New control modules are delivered with pre-programmed values from the factory. The control module must be programmed with the relevant data for the market, body type etc. in order for it to function correctly after replacement. The programmed values must therefore be read from the existing control module and noted.
- Ignition on.
- Read off the values programmed into the control module.
Other information
- To access / replace the central electronic module (CEM), see «Replacing central electronic module (CEM)»(ref-441299-S20562345372011121500000) .
- For information about programming, see «Description of programmed data»(ref-441356-S33230254432011121500000) .
- Continue Refer to «Information»(ref-441355-S20764462382011121500000)
In case of this defect, troubleshooting is not followed by verification.
The information can be displayed again or the fault-tracing for this fault can be interrupted.
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
Verification
HINT: After carrying out the repair, check that the fault has been remedied.
Scheme 109
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on. Flash the high beam with the turn signal lamp stalk and read off the signal from the turn signal lamp switch. The value must be On.
Is the value On?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S32149672812011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
HINT: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on. Turn the lighting switch to position 1. Read off the signal to the parking lamps. The value must be On.
Is the value On?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S14987695772011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
HINT: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on. Read off the signal from the ignition switch. The value must be Position 2.
Is the value Position 2?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S28254707182011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
HINT: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on. Read off the signal from the ignition switch. The value must be Position 2.
Is the value Position 2?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S03765662632011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
HINT: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on. Read off the signal from the ignition switch. The value must be Position 2.
Is the value Position 2?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S30467608902011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
HINT: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on. Turn the lighting switch to position 1 and activate the switch for the front fog lamps. Read off the signal from the switch for the front fog lamps. The value must be On.
Is the value On?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S34063460972011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
HINT: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on. Turn the lighting switch to position 1 and activate the switch for the rear fog lamp. Read off the signal from the switch for the rear fog lamp. The value must be On.
Is the value On?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S25636681332011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
HINT: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on. Turn the rheostat between its limit positions. Read off the angle of turn. The value must change between 0° and 60°.
Is the rheostat working?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S37237755152011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
Checking for interference
- Ignition off. Check that the wiring between combined instrument panel connector B #15 and: central electronic module (CEM) B2 #16 each engine control module (ECM) connector ECC connector #4 cruise control connector #13 is not too close to sources of interference such as electric motors, ignition cables and car telephone wiring. Other information For information about signals, see «Signal specification»(ref-441301-S11047559212011121500000) .
- Continue Refer to «Verification»(ref-441355-S00908569752011121500000)
HINT: After carrying out the repair, check that the fault has been remedied.
Scheme 110
- Ignition off.
- Reinstall the connectors, components etc.
- Start the engine. Raise the car and remove both front wheels. NOTE: Diagnostic trouble codes (DTCs) may be stored in the ABS system when the rear wheels are stationary and the front wheels rotate. Erase any diagnostic trouble codes (DTCs) stored in the ABS system after fault-tracing. NOTE: Ensure that the front wheels are stationary when the gear selector is moved. Read off the vehicle speed signal at different speeds.
Is the speed displayed reasonable?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S19596997142011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
HINT: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on. Activate the high beam. The high beam must both light and go out.
Does the high beam both light and go out?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S08276744072011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
HINT: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on. Activate the high beam. The high beam must both light and go out.
Does the high beam both light and go out?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S25875946012011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
HINT: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on. Activate the high beam. The high beam must both light and go out.
Does the high beam both light and go out?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S24335657802011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
HINT: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on. Activate the instrument lighting at 42% and 100% strength. Check that the luminance of the instrument lighting changes.
Is the instrument lighting OK?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S41746996662011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
The control module has registered an internal fault. Try a new control module.
Note. New control modules are delivered with pre-programmed values from the factory. The control module must be programmed with the relevant data for the market, body type etc. in order for it to function correctly after replacement. The programmed values must therefore be read from the existing control module and noted.
- Ignition on.
- Read off the values programmed into the control module.
Other information
- To access / replace the central electronic module (CEM), see «Replacing central electronic module (CEM)»(ref-441299-S20562345372011121500000) .
- For information about programming, see «Description of programmed data»(ref-441356-S33230254432011121500000) .
- Continue Refer to «Information»(ref-441355-S07095066302011121500000)
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
The control module has registered an internal fault. Try a new control module.
Note. New control modules are delivered with pre-programmed values from the factory. The control module must be programmed with the relevant data for the market, body type etc. in order for it to function correctly after replacement. The programmed values must therefore be read from the existing control module and noted.
- Ignition on.
- Read off the values programmed into the control module.
Other information
- To access / replace the central electronic module (CEM), see «Replacing central electronic module (CEM)»(ref-441299-S20562345372011121500000) .
- For information about programming, see «Description of programmed data»(ref-441356-S33230254432011121500000) .
- Continue Refer to «Information»(ref-441355-S01652028892011121500000)
In case of this defect, troubleshooting is not followed by verification.
The information can be displayed again or the fault-tracing for this fault can be interrupted.
Scheme 111
- Ignition off. Check that the wiper motor and wiper arms do not bind. HINT: The trouble code may have been caused by wiper blades frozen stuck. If no fault is found, try with a new wiper motor. Remedy as necessary. Other information See «Signal specification»(ref-441301-S11047559212011121500000) To access/replace the wiper motor, see: «Windshield washer / wiper mechanism and motor»(ref-441357-S22059995412011121500000)
- Continue Refer to «Information»(ref-441355-S05117846952011121500000)
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
Checking components
- Ignition off. Check that the wiper motor and wiper arms do not bind. If no fault is found, try with a new wiper motor. Remedy as necessary. Other information See «Signal specification»(ref-441301-S11047559212011121500000) To access/replace the wiper motor, see: «Windshield washer / wiper mechanism and motor»(ref-441357-S22059995412011121500000)
- Continue Refer to «Verification»(ref-441355-S02461123782011121500000)
HINT: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on. Activate the windshield wiper intermittent position using the washer / wiper switch. Read off the signal from the parking position switch. It must be both Parked and Not parked.
Is the signal OK?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S08101444282011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
- Ignition off. Check the cable between the control module's connector B2#12 (#A12) and the wiper motor's connector #4 for open circuit, contact resistance, and oxidation. «Checking wiring and terminals. Intermittent faults»(ref-441291-S36551477422011121500000) Check that the wiper motor and wiper arms do not bind. HINT: The trouble code may have been caused by wiper blades frozen stuck. If no fault is found, try with a new wiper motor. Remedy as necessary. Other information See «Connecting the breakout box»(ref-441300-S21187382202011121500000) See «Signal specification»(ref-441301-S11047559212011121500000) To access/replace the wiper motor, see: «Windshield washer / wiper mechanism and motor»(ref-441357-S22059995412011121500000)
- Continue Refer to «Information»(ref-441355-S00684699452011121500000)
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
HINT: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on. Activate the windshield wiper intermittent position using the washer / wiper switch. Read off the signal from the parking position switch. It must be both Parked and Not parked.
Is the signal OK?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S39617489052011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
The control module has registered an internal fault. Try a new control module.
Note. New control modules are delivered with pre-programmed values from the factory. The control module must be programmed with the relevant data for the market, body type etc. in order for it to function correctly after replacement. The programmed values must therefore be read from the existing control module and noted.
- Ignition on.
- Read off the values programmed into the control module.
Other information
- To access / replace the central electronic module (CEM), see «Replacing central electronic module (CEM)»(ref-441299-S20562345372011121500000) .
- For information about programming, see «Description of programmed data»(ref-441356-S33230254432011121500000) .
- Continue Refer to «Information»(ref-441355-S06815923752011121500000)
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
The control module has registered an internal fault. Try a new control module.
Note. New control modules are delivered with pre-programmed values from the factory. The control module must be programmed with the relevant data for the market, body type etc. in order for it to function correctly after replacement. The programmed values must therefore be read from the existing control module and noted.
- Ignition on.
- Read off the values programmed into the control module.
Other information
- To access / replace the central electronic module (CEM), see «Replacing central electronic module (CEM)»(ref-441299-S20562345372011121500000) .
- For information about programming, see «Description of programmed data»(ref-441356-S33230254432011121500000) .
- Continue Refer to «Information»(ref-441355-S22047662832011121500000)
In case of this defect, troubleshooting is not followed by verification.
The information can be displayed again or the fault-tracing for this fault can be interrupted.
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
HINT: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on.
- Activate the warning lamp for the bulb failure warning sensor. The lamp must both light and go out.
Does the lamp light and go out?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S01661654802011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
HINT: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on.
- Activate the warning lamp for the bulb failure warning sensor. The lamp must both light and go out.
Does the lamp light and go out?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S05341580942011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
HINT: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on. Read off the battery voltage. It must be normal.
Is the battery voltage normal?
- YES VERIFIED: Troubleshooting has been completed.
- NO Refer to «Information»(ref-441355-S20907243812011121500000)
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.