Home/Volkswagen/Jetta/Volkswagen Jetta III (1992-1998)/Repair manual/Mechanical/2.0L Engine Mechanical - Aba (A3 Platform): Specifications
Contents Wiring diagrams Section: Mechanical All sections

2.0L Engine Mechanical - Aba (A3 Platform): Specifications Volkswagen Jetta III

Mechanical ~179 words

Engine specifications (Golf, GTI, Jetta)

Engine CodeABAABAABA
Manufactured from07.9208.9508.95
Manufactured :to07.95
Displacement : liters2.02.02.0
Output : Hp (kW) @ RPM115 (85) @ 5400115 (85) @ 5400115 (85) @ 5400
Torque Ft lb (Nm) @ RPM165 (122) @ 3200165 (122) @ 3200165 (122) @ 3200
Bore : mm (in.)82.5 (3.248)82.5 (3.248)82.5 (3.248)
Stroke : mm (in.)92.8 (3.653)92.8 (3.653)92.8 (3.653)
Compression ratio9.6: 19.0: 19.0: 1
Fuel requirement : RON (minimum)91 lead-free91 lead-free91 lead-free
Fuel injection systemMotronic Multiport Fuel Injection (MFI)Motronic M5.9 Multiport Fuel Injection (MFI)
Ignition systemMotronicMotronic M5.9
Knock controlYesYesYes
On Board Diagnostic (OBD)YesOBD II (Tier 1)OBD II (T-LEV)
Oxygen Sensor (O2S) controlYes (1 sensor)Yes (2 sensors)
Three way catalytic converter (TWC)YesYesYes
Exhaust Gas Recirculation (EGR)YesNoNo
Secondary Air Injection (AIR)NoNoYes
Enhanced EVAP systemNoYesYes
Leak Detection Pump (LDP)NoYes (1)Yes (1)
(1) Not installed on all vehicles during m.y. 1996; not operational on vehicles up to 10.95.
(1)Not installed on all vehicles during m.y. 1996; not operational on vehicles up to 10.95.

ENGINE SPECIFICATIONS (GOLF, GTI, JETTA)

Engine specifications (Cabrio)

Engine codeABAABA
Manufactured from01.9408.95
Manufactured to07.95
Displacement : liters2.02.0
Output : Hp (kW) @ RPM115 (85) @ 5400115 (85) @ 5400
Torque : Ft lb (Nm) @ RPM165 (122) @ 3200165 (122) @ 3200
Bore : mm (in.)82.5 (3.248)82.5 (3.248)
Stroke : mm (in.)92.8 (3.653)92.8 (3.653)
Compression ratio9.4:19.4:1
Fuel requirement : RON (minimum)91 lead-free91 lead-free
Fuel injection systemMotronic Multiport Fuel Injection (MFI)Motronic M5.9 Multiport Fuel Injection (MFI)
Ignition systemMotronicMotronic M5.9
Knock controlYesYes
On Board Diagnostic (OBD)YesOBD II (Tier 1)
Oxygen Sensor (O2S) controlYes (1 sensor)Yes (2 sensors)
Three way catalytic converter (TWC)YesYes
Exhaust Gas Recirculation (EGR)YesNo
Secondary Air Injection (AIR)NoNo
Enhanced EVAP systemNoNo
Leak Detection Pump (LDP)NoNo

ENGINE SPECIFICATIONS (CABRIO)

Tightening torques

Fastener connectionTightening torque
Engine to transmission
M1060 Nm (44 ft lb)
M1280 Nm (59 ft lb)
Flywheel guard
M710 Nm (7 ft lb)
Axle shafts to drive flanges45 Nm (33 ft lb)
Exhaust pipe to manifold40 Nm (30 ft lb)
Engine mount to body50 Nm (37 ft lb)

TIGHTENING TORQUES (ENGINE REMOVAL/INSTALLATION)

Engine/transmission mounts, tightening torques

  1. Bolts oiled

Tightening torque

FastenerPart no.Tightening torque
Torx® boltN 903 659 0225 Nm (18 ft lb)
Collar screw058 109 28115-20 Nm (11-15 ft lb)
Bolt/washer assy (2)N 902 809 017-11 Nm (62 -97 in. lb)
NutN 011 006 277-11 Nm (62 -97 in. lb)

TIGHTENING TORQUE

CAUTIONPart Numbers are for reference only. Always check with your Parts Dept. for the latest information.

Oil Capacities up to MY 2000

From my 2001, see Fluid Capacity Chart in owner's manual.

Oil capacity

  1. With oil filter: 3.8 liters (4.0 qt.)

Oil specifications

  1. The following terms must appear on the oil container singly or in combination with other designations
  2. VW 502 00 or VW500 00 or VW501 01
  3. ACEA A2 or ACEA A3
  4. API-SJ or API-SL
  5. Engine oils are graded according to their viscosity. The proper grade to be used in your engine depends on existing climatic or seasonal conditions.
  6. The engine oil which was first put into your engine has a viscosity grade of SAE 5W-40. You can use this oil over all temperature ranges for normal driving. If engine oil viscosity grade SAE 5W-40 is not available, you can also use SAE 5W-30.