| Camshaft timing gear assembly x Camshaft | 54 | 551 | 40 |
| Camshaft bearing cap x Cylinder head | No. 1 | 30 | 301 | 22 |
| Other | 9.0 | 92 | 80 in.*lbf |
| No. 2 camshaft bearing cap x Cylinder head | No. 2 | 30 | 301 | 22 |
| Other | 9.0 | 92 | 80 in.*lbf |
| Camshaft timing gear or sprocket x No. 2 camshaft | 54 | 551 | 40 |
| No. 1 chain tensioner assembly x Timing chain or belt cover sub-assembly | 9.0 | 92 | 80 in.*lbf |
| Cylinder head cover sub-assembly x Cylinder head sub-assembly | Bolt A | 11 | 112 | 8 |
| Bolt B | 14 | 143 | 10 |
| Nut | 11 | 112 | 8 |
| Cylinder head sub-assembly x Cylinder block | 1st | 70 | 714 | 52 |
| 2nd | Turn 90° | Turn 90° | Turn 90° |
| Ground cable x Cylinder head sub-assembly | 8.4 | 86 | 74 in.*lbf |
| Chain tensioner plate x Cylinder block | 12 | 122 | 9 |
| Oil pump drive shaft sprocket x Oil pump | 30 | 301 | 22 |
| No. 1 chain vibration damper x Cylinder head sub-assembly | 9.0 | 92 | 80 in.*lbf |
| No. 1 chain vibration damper x Cylinder block | 9.0 | 92 | 80 in.*lbf |
| Chain tensioner slipper x Cylinder block | 19 | 194 | 14 |
| Timing chain guide x Cylinder block | 9.0 | 92 | 80 in.*lbf |
| V-ribbed belt tensioner assembly x Timing chain or belt cover sub-assembly | 60 | 607 | 44 |
| Crankshaft pulley x Crankshaft | 180 | 1835 | 133 |
| Oil pan sub-assembly x Stiffening crankcase assembly or Timing chain or belt cover sub-assembly | 9.0 | 92 | 80 in.*lbf |
| Idler pulley sub-assembly x Cylinder block sub-assembly | 50 | 510 | 37 |
| Engine mounting insulator sub-assembly RH x Transverse engine mounting bracket | Bolt A | 52 | 530 | 38 |
| Bolt B | 95 | 969 | 70 |
| Nut A | 95 | 969 | 70 |
| Nut B | 52 | 530 | 38 |
| Exhaust manifold converter sub-assembly x Cylinder head sub-assembly | 37 | 377 | 27 |
| Engine oil level dipstick guide x Cylinder block | 9.0 | 92 | 80 in.*lbf |
| For Automatic Transaxle: Drive plate and ring gear sub-assembly x Crankshaft | 98 | 999 | 72 |
| For Manual Transaxle: Flywheel sub-assembly x Crankshaft | 130 | 1326 | 96 |
| No. 1 engine hanger x Cylinder head sub-assembly | 38 | 387 | 28 |
| No. 2 engine hanger x Cylinder head sub-assembly | 38 | 387 | 28 |
| For 2WD: Drive shaft bearing bracket x Cylinder block | 64 | 653 | 47 |
| Engine mounting insulator sub-assembly LH x Frame | 52 | 530 | 38 |
| Engine mounting insulator sub-assembly LH x Engine mounting bracket | 56 | 571 | 41 |
| Front engine mounting insulator sub-assembly x Front cross member sub-assembly | Through bolt | 73 | 744 | 54 |
| Bolt | 81 | 827 | 59 |
| Rear engine mounting insulator sub-assembly x Rear engine mounting bracket | 65 | 663 | 48 |
| Transmission control cable assembly x Control shaft lever | 12 | 122 | 9 |
| For Manual Transaxle: Ground cable x Transaxle | 13 | 130 | 10 |
| For Automatic Transaxle: Ground cable x Transaxle | 26 | 260 | 19 |
| Engine wire harness x Engine room relay block | 8.4 | 85 | 74 in.*lbf |
| Battery carrier x Frame | 13 | 133 | 10 |
| Battery clamp x Battery clamp bolt | 3.5 | 36 | 31 in.*lbf |
| Battery clamp x Body | 6.5 | 66 | 58 in.*lbf |
| Air cleaner case x Engine mounting insulator sub-assembly LH | 7.0 | 71 | 62 in.*lbf |
| Radiator reserve tank assembly x Body | 7.0 | 71 | 62 in.*lbf |
| No. 1 engine cover sub-assembly x Cylinder head cover sub-assembly | 9.0 | 92 | 80 in.*lbf |
| Balance shaft housing x Stiffening crankcase assembly | 1st | 22 | 220 | 16 |
| 2nd | Turn 90° | Turn 90° | Turn 90° |
| Stiffening crankcase assembly x Cylinder block | 24 | 245 | 18 |
| No. 1 taper head screw plug x Cylinder block | 26 | 265 | 19 |
| Oil control valve filter x Cylinder head sub-assembly | 30 | 306 | 22 |
| Inlet water housing drain cock assembly x Inlet water housing | 25 | 255 | 18 |
| Plug x Inlet water housing drain cock | 13 | 130 | 10 |
| Camshaft timing oil control valve assembly x Cylinder head sub-assembly | 9.0 | 92 | 80 in.*lbf |
| Crankshaft position sensor x Timing chain or belt cover sub-assembly | 9.0 | 92 | 80 in.*lbf |
| Oil pan drain plug x Oil pan sub-assembly | 25 | 255 | 18 |
| Camshaft position sensor x Cylinder head sub-assembly | 9.0 | 92 | 80 in.*lbf |
| Oil filter union x Stiffening crankcase assembly | 30 | 306 | 22 |
| Ventilation valve sub-assembly x Cylinder head cover sub-assembly | 19 | 194 | 14 |
| Radio setting condenser x Cylinder head sub-assembly | 10 | 102 | 7 |
| No. 1 water by-pass pipe x Cylinder block | 9.0 | 92 | 80 in.*lbf |
| Stud bolt x Cylinder head sub-assembly | Bolt A | 5.0 | 51 | 44 in.*lbf |
| Bolt B | 5.0 | 51 | 44 in.*lbf |
| Bolt C | 9.5 | 97 | 84 in.*lbf |
| Bolt D | 9.5 | 97 | 84 in.*lbf |
| No. 1 straight head screw plug x Cylinder head sub-assembly | 86 | 877 | 64 |
| Stud bolt x Cylinder block | Bolt A | 22 | 220 | 16 |
| Bolt B | 5.0 | 51 | 44 in.*lbf |
| Bolt C | 9.5 | 97 | 84 in.*lbf |
| Bolt D | 5.0 | 51 | 44 in.*lbf |
| No. 1 oil nozzle sub-assembly x Cylinder block | 7.0 | 71 | 62 in.*lbf |
| Crankshaft bearing cap x Cylinder block | 1st | 20 | 204 | 15 |
| 2nd | 40 | 408 | 30 |
| 3rd | Turn 90° | Turn 90° | Turn 90° |
| Connecting rod cap x Connecting rod | 1st | 25 | 250 | 18 |
| 2nd | Turn 90° | Turn 90° | Turn 90° |
