Maintenance Reminder Light Reset Procedures: Diagnosis Suzuki Equator I

ID Registration With Suzuki Scan Tool

1. Connect Suzuki scan tool to data link connector (DLC).
2. Turn ignition switch to ON.
3. Activate each tire pressure sensor according to the instructions displayed on Suzuki scan tool, within 90 seconds (this step also requires sensor activation tool 09945-86510). NOTE: When tire pressure sensor is to be activated, set the sensor activation tool (09945-86510) to the same position as shown in the illustration (Scheme 1) If the special tool is set to other positions, there is a possibility that tire pressure sensor cannot be activated. When tire pressure sensor is activated, flashing LED and beeping sound of special tool indicate an activation of the tire pressure sensor. In the case that the LED does not flash and beeping sound is not heard, replace faulty tire pressure sensor.
4. When tire pressure sensor is activated, ID code of the tire pressure sensor is registered automatically in BCM. When "ID Registration status" indicated on Suzuki scan tool is "Complete", registration has been completed. If "Time Out" is indicated, perform the registration procedure all over. Also, it is possible to check the number of ID codes of tire pressure sensors received by BCM by observing the flashing pattern of the low tire pressure warning light. NOTE: When BCM receives each ID code of 4 tire pressure sensors, BCM turns ON low tire pressure warning light in combination meter for 5 seconds.
5. Turn ignition switch OFF, and disconnect Suzuki scan tool from DLC.

Scheme 1

ID Registration Without Suzuki Scan Tool

1. Confirm that all doors are closed and ignition key is out of ignition key cylinder.
2. Open driver side door.
3. Perform the following Steps a) to c) within 15 seconds after ignition switch turned ON: Press driver side door switch hand within 5 seconds after ignition switch turned ON. Keep the switch pressed for 2 seconds. Release driver side door switch and then press driver side door switch for 2 seconds or more by hand. Release driver side door switch and then press driver side door switch for 2 to 5 seconds by hand.
4. Using sensor activation tool (09945-86510), activate each tire pressure sensor within 90 seconds. NOTE: When tire pressure sensor is to be activated, set the sensor activation tool (09945-86510) to the same position as shown in the illustration (Scheme 1) If the special tool is set to other positions, there is a possibility that tire pressure sensor cannot be activated. When tire pressure sensor is activated, flashing LED and beeping sound of special tool indicate an activation of the tire pressure sensor. In the case that the LED does not flash and beeping sound is not heard, replace faulty tire pressure sensor.
5. When tire pressure sensor is activated, ID code of the tire pressure sensor is registered automatically in BCM. When "ID Registration status" indicated on Suzuki scan tool is "Complete", registration has been completed. If "Time Out" is indicated, perform the registration procedure all over. Also, it is possible to check the number of ID codes of tire pressure sensors received by BCM by observing the flashing pattern of the low tire pressure warning light. NOTE: When BCM receives each ID code of 4 tire pressure sensors, BCM turns ON low tire pressure warning light in combination meter for 5 seconds.
6. After registration is completed, turn ignition switch OFF.

1. Confirm that ignition mode of keyless push start system is OFF
2. Connect Suzuki scan tool to data link connector (DLC).
3. Push engine switch to change ignition mode to ON.
4. Select "TPS ID registration" of "Utility" under "keyless start control module" mode of Suzuki scan tool.
5. Using recommended tool VT55 at tire pressure sensor, activate each sensor according to the instructions displayed on Suzuki scan tool, within 180 seconds.
6. When tire pressure sensor is activated, ID code of tire pressure sensor is registered automatically in keyless start control module. When "ID code registration status" indicated on Suzuki scan tool is "Complete", registration has been completed. If "Time Out" is indicated, perform all the registration procedures again. Also, it is possible to check the number of ID codes of tire pressure sensors received by keyless start control module by observing the flashing pattern of low tire pressure warning light NOTE: When registering tire pressure sensor ID codes using Suzuki scan tool, former ID codes are cleared. Therefore, if registration is not completed, perform the above steps again. NOTE: When keyless start control module receives each ID code of 4 tire pressure sensors, keyless start control module turns ON low tire pressure warning light in combination meter for 5 seconds.
7. Push engine switch to change ignition mode to OFF and disconnect Suzuki scan tool from DLC.

1. Confirm that all doors are closed and ignition mode of keyless push start system is OFF.
2. Open driver side door.
3. Perform the following Steps a) to c) within 15 seconds after ignition switch turned ON: Press driver side door switch hand within 5 seconds after ignition mode is ON. Keep the switch pressed for 2 seconds. Release driver side door switch and then press driver side door switch for 2 seconds or more by hand. Release driver side door switch and then press driver side door switch for 2 to 5 seconds by hand.
4. Using recommended tool VT55 at tire pressure sensor, activate each sensor within 180 seconds.
5. When tire pressure sensor is activated, ID code of tire pressure sensor is registered automatically in keyless start control module. When "ID code registration status" indicated on Suzuki scan tool is "Complete", registration has been completed. If "Time Out" is indicated, perform all the registration procedures again. Also, it is possible to check the number of ID codes of tire pressure sensors received by keyless start control module by observing the flashing pattern of low tire pressure warning light NOTE: If registration of tire pressure sensor ID codes are not completed within 180 seconds, former ID codes remain in keyless start control module. Therefore, perform the above steps again. NOTE: When keyless start control module receives each ID code of 4 tire pressure sensors, keyless start control module turns ON low tire pressure warning light in combination meter for 5 seconds.
6. Push engine switch to change ignition mode to OFF after registration is completed.