OPERATION
For operation procedures, refer to the "PC application help for Subaru Select Monitor".
For operation procedures, refer to the "PC application help for Subaru Select Monitor".
For operation procedures, refer to the "PC application help for Subaru Select Monitor".
For operation procedures, refer to the "PC application help for Subaru Select Monitor".
Note. Initial diagnosis of electronic throttle control is performed after memory clearance. Wait for 10 seconds or more after turning the ignition switch to ON, and then start the engine.
- On «Main Menu» display, select {Each System Check}.
- On «System Selection Menu» display, select {Keyless access system}.
- On «Keyless access system» display, select {Work Support}.
- Select {Function Check Sequence}.
- Select {Keyless access system check}.
- Select the transmitter to be checked and click [OK].
- Select [Exit] to exit the system check. The screen will return to the «Keyless access system check» screen.
| Data | Customize setting | Remarks |
|---|---|---|
| Keyless access system check | Driver side external transmitter - internal tuner | When the setting content on the left is selected, the access key is neared to the selected transmitter (access antenna) and collation matches, the buzzer will sound. |
| Passenger side external transmitter - internal tuner | ||
| Fr internal transmitter - internal tuner | ||
| Rr internal transmitter - internal tuner | ||
| Trunk internal transmitter, interior tuner | ||
| Trunk external transmitter - internal tuner | ||
| R gate internal transmitter - internal tuner | ||
| R gate external transmitter - internal tuner | ||
| Immobilizer amplifier transmission | ||
| Collation result history Clear | Execution |
Note. For detailed operation procedures, refer to "PC application help for Subaru Select Monitor".
- On «Main Menu» display, select {Each System Check}.
- On «System Selection Menu» display, select {Keyless access system}.
- On «Keyless access system» display, select {Work Support}.
- Select {System Operation Check Mode}.
- Select the check point and click [OK].
- Select [Exit] to exit the drive item mode. The screen will return to the «Drive item» screen.
Note. Each output check continues to run for five seconds before stopping automatically. The voltage will stabilize at about 3 mV when the voltage is measured using tester during output.
| Data | Keyless access CM output check | Remarks |
|---|---|---|
| Tuner power supply ON (indoor tuner) | Output | Perform check of the power supply for the receiver. |
| Stop | ||
| Driver's external transmitter | Output | Perform driver's side door outside antenna output check. |
| Stop | ||
| Passenger's external transmitter | Output | Perform passenger's side door outside antenna output check. |
| Stop | ||
| STSW | Output | Turn on the STSW. (2) |
| Stop | ||
| IGN2 | Output | Turn on the IGN2. |
| Stop | ||
| IGN1 | Output | Turn on the IGN1. |
| Stop | ||
| ACC | Output | Turn on the ACC. |
| Stop | ||
| Start SW character illumination lighted | Output | Perform ON output of the push button ignition switch back-up light. (1) |
| Stop | ||
| Start SW indicator lighted (green) | Output | Perform ON output of the push button ignition switch back-up light. (1) |
| Stop | ||
| Start SW indicator lighted (orange) | Output | Perform ON output of the push button ignition switch back-up light. (1) |
| Stop | ||
| Steering lock power supply | Output | Output power supply signal from power supply CM to steering lock CM. |
| Stop | ||
| (1) When lit by a condition other than for a system operation check mode, it will not become unlit even when set to OFF or no output. (2) When performed with ignition switch ON, engine will start. Therefore, great care must be exercised. | ||
| (1) | When lit by a condition other than for a system operation check mode, it will not become unlit even when set to OFF or no output. |
| (2) | When performed with ignition switch ON, engine will start. Therefore, great care must be exercised. |
Note. For detailed operation procedures, refer to "PC application help for Subaru Select Monitor".
See also:
• PROCEDURE