Lan Communication System - Lan (Diagnostics): Overview Subaru Forester SH

OPERATION

1. On the «Main Menu» display screen, select {Each System Check}.
2. On the «Each System Check» menu display screen, select the {Integ. unit mode}.
3. Select the [OK] after the information of body integrated unit type is displayed.
4. On the «Integ. unit mode» display screen, select the {Diagnostic Code(s) Display}.
5. Record the DTC displayed. NOTE: For details concerning the operation procedure, refer to the PC application help for Subaru Select Monitor. For details concerning DTC, refer to "List of Diagnostic Trouble Code (DTC)". Refer to «LIST OF DIAGNOSTIC TROUBLE CODE (DTC)»(ref-325333-S05426581352009071800000) .

1. On the «Main Menu» display screen, select the {2. Each System Check}.
2. On the «System Selection Menu» display screen, select the {Integ. unit mode}.
3. Press the [OK] key after the information of body integrated unit type is displayed.
4. On the «Integ. unit mode failure diag» display screen, select {Clear Memory} and press the [OK] key. SCAN TOOL DISPLAY REFERENCE Display Contents to be monitored Clear Memory? Clear function of DTC and freeze frame data
5. When "Done" is shown on the display screen, turn the ignition switch to OFF. NOTE: For details concerning the operation procedure, refer to the PC application help for Subaru Select Monitor.

1. On the «Main Menu» display screen, select {Each System Check}.
2. On the «System Selection Menu» display screen, select the {Integ. unit mode}.
3. On the «Integ. unit mode failure diag» display screen, select the {Current Data Display & Save}.
4. Using the scroll key, scroll the display screen up or down until the desired data is shown.

1. On the «Main Menu» display screen, select {Each System Check}.
2. On the «System Selection Menu» display screen, select the {Integ. unit mode}.
3. On the «Integ. unit mode failure diag» display screen, select the {ECM customizing}.
4. Change the setting with UP/DOWN key and set with the [OK] key. List of function setting item (ECM customizing) CUSTOMIZE SETTING DATA REFERENCE CHART Data Initial setting value Customize setting Remarks Off delay time Normal Delay time below can be selected by setting. After door closed After keyless unlock OFF 0 seconds 0 seconds Short 10 seconds 10 seconds Normal 20 seconds 20 seconds Long 30 seconds 30 seconds Auto lock time 30 seconds 0 - 60 sec. Workable when Auto locking is set to "ON" and Automatic locking setup is "ON". Time can be changed by 10 seconds: 0 (OFF) - 60 (maximum). Rr defogger op. mode 15 min. 15 min. Wiper deicer stops in 15 minutes automatically after switch is turned to ON. Continuous The wiper deicer activates for 15 minutes and turns inactive for 2 minutes repeatedly until the switch is turned OFF. Wiper deicer op. mode 15 min. 15 min. Wiper deicer stops in 15 minutes automatically after switch is turned to ON. Continuous The wiper deicer activates for 15 minutes and turns inactive for 2 minutes repeatedly until the switch is turned OFF. Security Alarm Setup OFF ON Security alarm (hazard, horn or siren) in active condition OFF Security alarm in inactive condition Impact Sensor Setup OFF ON Workable when Impact Sensor Setup is set to "ON". Impact sensor function becomes activated. OFF Impact sensor in inactive condition (Set to "OFF" in models without sensors). Alarm delay setup ON After the keyless lock operation, the alarm monitor starts after the following delay time has passed. ON Delay time is 30 seconds. OFF Delay time is 0 seconds. Lockout prevention ON ON Lockout prevention in inactive condition (The function does not operate if safety knob is locked by hand). OFF Lockout prevention in inactive condition Impact sensor (OP) OFF ON Vehicle is controlled in impact sensor equipped mode. (Make sure to set to OFF for models without the impact sensor. When set to ON, hazard, the horn or siren will operate after doors are locked by the keyless entry system operation (Alarm monitor start). OFF Vehicle is controlled in no impact sensor mode. Siren setting (OP) OFF ON Make sure to set to OFF for models without the siren. OFF Answer-back buzzer setup ON ON Workable when answer-back buzzer setup is set to "ON". When lock/unlock is selected by keyless entry system operated, hazard answer-back buzzer operates. OFF When lock/unlock is selected by keyless entry system operated, answer-back buzzer does not sound. Hazard answer-back setup ON ON Workable when hazard answer-back setup is set to "ON" When lock/unlock is selected by keyless entry system operated, hazard answer-back buzzer operates. OFF When lock/unlock is selected by keyless entry system operated, hazard answer-back does not operate. Automatic locking setup ON ON Not supported OFF Ans.-back Buzzer ON ON Vehicle is controlled in answer-back buzzer equipped mode. OFF Vehicle is controlled in answer-back buzzer non-equipped mode. (Make sure to set to "OFF" in models without answer back buzzers). Auto locking ON ON Not supported OFF Initial keyless setting - - - Execution Settings of keyless entry system are initialized. (No. 2:30 sec, No. 11: ON, No. 12: ON, No. 13: ON, No. 14: ON) Initial button setting - - - Execution Settings of each function are initialized. (No. 1: Normal, No. 3:15 min., No. 4:15 min., No. 8: ON) Initial Security setting - - Not supported Execution Passive Alarm OFF ON Setting only for North American models OFF Door open warning OFF ON If detecting door open for 30 minutes, room light, key ring illumination are turned off to prevent battery run-out. OFF Room light, key illumination and door warning light is not turned off. Belt Warning Switch ON ON When using normally OFF Stop the belt warning buzzer beep and warning light illumination.
5. After setting, make sure that vehicle equipment is same as the setting changed in the {Current Data Display & Save}. CAUTION: The above settings must match the actual vehicle equipment. Do not change settings other than the above while setting the functions. Be sure not to change Factory or Market setting except installation of new body integrated unit. NOTE: For details concerning the operation procedure, refer to the PC application help for Subaru Select Monitor.

Note. In order to check the body integrated unit function, inspect the body integrated unit and actuator using Subaru Select Monitor without operating switches.

Scheme 8

1. On the «Main Menu» display screen, select {Each System Check}.
2. On the «System Selection Menu» display screen, select the {Integ. unit mode}.
3. On the «Integ. unit mode failure diag» display screen, select the {Function check}.
4. Select the item to be operated on the «Function check» display screen with «UP/Down key» and press the [Next] button.
5. Pressing [Next] starts, [End] cancels the operation and [OK] returns to the System Operation Check Mode display screen.

Note. If not equipped (based on area or condition), process will not go on. For details concerning the operation procedure, refer to the PC application help for Subaru Select Monitor.