Fastener Tightening Specifications
| Application | Specification |
|---|
| Metric | English |
| Front Bucket Seat Back Frame Bolt - Fold Flat | 60 N.m | 44 lb ft |
| Front Bucket Seat Back Panel Screw | 1 N.m | 9 lb in |
| Front Bucket Seat Back Recliner Trim Panel Screws | 1 N.m | 9 lb in |
| Front Bucket Seat Cushion Frame Bolt | 12 N.m | 106 lb in |
| Front Bucket Seat Cushion Inner Trim Panel Screw - Fold Flat | 1 N.m | 9 lb in |
| Front Bucket Seat Cushion Outer Trim Panel Screw | 1 N.m | 9 lb in |
| Front Bucket Seat Rear Adjuster Bolt | 50 N.m | 37 lb ft |
| Front Bucket Seat Recliner Bolt - Fold Flat | 45 N.m | 33 lb ft |
| Front Bucket Seat Recliner Lever Bolt | 12 N.m | 106 lb in |
| Front Seat Safety Belt Buckle Bolt | 45 N.m | 33 lb ft |
| Inboard Seat Back Frame Nuts - Non-Fold Flat | 25 N.m | 18 lb ft |
| Outboard Seat Back Frame Nuts - Non-Fold Flat | 17 N.m | 13 lb ft |
| Rear Seat Back Latch Bolt | 12 N.m | 106 lb in |
| Side Impact Tube Bolt - 2-Way Adjuster | 25 N.m | 18 lb ft |
| Side Impact Tube Bolt - 4-Way Adjuster | 25 N.m | 18 lb ft |
| Teardrop Washer Bolt | 35 N.m | 26 lb ft |
Fastener Tightening Specifications
Seat - Manual Adjuster Does Not Unlock
| Condition | Action |
|---|
| IMPORTANT: Replace all seat adjusters as an assembly Replace both sides at the same time. |
| The adjuster latch is binding | Inspect the seat adjuster handle for damage. Replace the handle if necessary. Replace the adjuster. |
| IMPORTANT |
|---|
| Replace all seat adjusters as an assembly Replace both sides at the same time. |
Seat - Manual Adjuster Does Not Unlock
Seat - Manual Adjuster Locks Between Lock Positions
| Condition | Action |
|---|
| IMPORTANT: Replace all seat adjusters as an assembly Replace both sides at the same time. |
| The right adjuster is rearward of the left adjuster. The right adjuster is forward of the left adjuster. | Visually inspect the installed seat to verify that the seat back is parallel to the seat cushion. Move the seat back until a parallel condition is achieved. |
| The seat back will not remain parallel. | On non-fold flat seats, replace the seat back frame. |
| IMPORTANT |
|---|
| Replace all seat adjusters as an assembly Replace both sides at the same time. |
Seat - Manual Adjuster Locks Between Lock Positions
Seat - Manual Adjuster Does Not Lock
| Condition | Action |
|---|
| IMPORTANT: Replace all seat adjusters as an assembly Replace both sides at the same time. |
| The seat adjusters were not parallel during installation. | Loosen the rear seat bolts. Position the seat fully forward. Tighten the bolts. Refer to Fastener Tightening Specifications . |
| IMPORTANT |
|---|
| Replace all seat adjusters as an assembly Replace both sides at the same time. |
Seat - Manual Adjuster Does Not Lock
Seat - Hard to Move Forward and Rearward
| Condition | Action |
|---|
| IMPORTANT: Replace all seat adjusters as an assembly Replace both sides at the same time. |
| The adjusters are not in parallel alignment with each other. | Loosen the floor pan attaching bolts. Position the seat fully forward. Tighten the bolts. Refer to Fastener Tightening Specifications . |
| IMPORTANT |
|---|
| Replace all seat adjusters as an assembly Replace both sides at the same time. |
Seat - Hard to Move Forward and Rearward
Seats - Adjuster Track Locks Ahead of Other Track
| Condition | Action |
|---|
| IMPORTANT: Replace all seat adjusters as an assembly Replace both sides at the same time. |
| The adjusters are out of time. | Remove and reinstall the front bucket seat. Refer to Seat Replacement - Front Bucket . |
| IMPORTANT |
|---|
| Replace all seat adjusters as an assembly Replace both sides at the same time. |
Seats - Adjuster Track Locks Ahead of Other Track
