Home/Saab/9-5/Saab 9-5 I рестайлинг (2001-2001)/Repair manual/Glass, Windows and Mirrors - 9-5/Menu "Activate"

Contents

Section: Glass, Windows and Mirrors - 9-5

To fit

Interior rear-view mirror with auto -dimming function, change of mirror glass

Background

Procedure

Protective equipment

Main fuse board 22a in dashboard

A. Permanently connected components

B. Connected components in LHD car

C. Connected components in RHD car

B. Additional components for left-hand-drive cars

C. Additional components for right-hand-drive cars

A. Connected components in LHD car

B. Connected components in RHD car

Connected components

Condition

Control module

Outputs

Inputs

Electrically heated rear window and door mirrors

Door mirrors with memory (PMM)

Menu "Read Values"

Menu "Activate"

Menu "System Information"

Probable cause

Adhesive and primer used when changing window glass

Windscreen and rear window

Side windows

Window lifts

Door mirrors

Interior rear-view mirror

Voltage +54 circuit

Ground

P bus and I bus

Electric heating uses the following information

Battery voltage +30

Battery voltage +15

Permanent bus fault

Intermittent bus faults

Incorrect values on the bus

The PMM uses the following information

PMM outputs the following information

Switch

Tilting the passenger door mirror

Electric window lifts

List of components

Electrically adjustable door mirrors, LHD

Electrically adjustable door mirrors, RHD

Electrically adjustable door mirrors with memory (PMM), LHD

Electrically adjustable door mirrors with memory (PMM), RHD

Auto-dimming mirror

All sections

Menu "Activate" Saab 9-5 I рестайлинг

Glass, Windows and Mirrors - 9-5

Activate	Condition for activating	Description	Use
Left Mirror In	Ignition ON	Processor affecting the transistors that control the position of the mirrors.	Checking control module output, electrical circuitry and actuator function. When output active, the mirror should move towards its end positions. Otherwise, use a test lamp to find the defect lead/component.
Left Mirror Out	Ignition ON	Processor affecting the transistors that control the position of the mirrors.	Checking control module output, electrical circuitry and actuator function. When output active, the mirror should move towards its end positions. Otherwise, use a test lamp to find the defect lead/component.
Left Mirror Up	Ignition ON	Processor affecting the transistors that control the position of the mirrors.	Checking control module output, electrical circuitry and actuator function. When output active, the mirror should move towards its end positions. Otherwise, use a test lamp to find the defect lead/component.
Left Mirror Down	Ignition ON	Processor affecting the transistors that control the position of the mirrors.	Checking control module output, electrical circuitry and actuator function. When output active, the mirror should move towards its end positions. Otherwise, use a test lamp to find the defect lead/component.
Right Mirror In	Ignition ON	Processor affecting the transistors that control the position of the mirrors.	Checking control module output, electrical circuitry and actuator function. When output active, the mirror should move towards its end positions. Otherwise, use a test lamp to find the defect lead/component.
Right Mirror Out	Ignition ON	Processor affecting the transistors that control the position of the mirrors.	Checking control module output, electrical circuitry and actuator function. When output active, the mirror should move towards its end positions. Otherwise, use a test lamp to find the defect lead/component.
Right Mirror Up	Ignition ON	Processor affecting the transistors that control the position of the mirrors.	Checking control module output, electrical circuitry and actuator function. When output active, the mirror should move towards its end positions. Otherwise, use a test lamp to find the defect lead/component.
Right Mirror Down	Ignition ON	Processor affecting the transistors that control the position of the mirrors.	Checking control module output, electrical circuitry and actuator function. When output active, the mirror should move towards its end positions. Otherwise, use a test lamp to find the defect lead/component.

MENU "ACTIVATE"