Wash/wipe Systems: Other Saab 9-4X I

Wiper/Washer System Components

The wiper/washer system consists of the following electrical components

1. Windshield Wiper Relay
2. Windshield Wiper Speed Control Relay
3. Windshield Washer Pump Relay
4. Windshield Outside Moisture Sensor
5. Windshield Washer Fluid Pump
6. Windshield Wiper Motor
7. Window Wiper/Washer Switch
8. Windshield Wiper Motor Fuse
9. Windshield Washer Fluid Pump Fuse
10. Body Control Module (BCM)
11. Rear Window Wiper Motor
12. Rear Window Wiper Motor Fuse
13. Rear Window Wiper Relay
14. Rear Window Washer Pump Relay
15. Headlamp Washer Fluid Pump Relay
16. Headlamp Washer Fluid Pump Fuse
17. Windshield Washer Fluid Level Switch

Windshield Wiper System

The body control module (BCM) determines the front wipe/wash system mode of operation by monitoring several signals from the front wipe/wash switch as indicated in the wiper switch

The front wipe/wash switch receives a reference ground signal from the BCM. Each input of the BCM provides a switched battery pull-up for each front wiper/washer switch output signal it receives. All the BCM inputs are recognized as active when the wiper switch provides a path to the referenced ground signal. The first signal received by the BCM is the result of 6 resistors in the front wiper switch configured as a resistor ladder network. This signal is connected to a BCM analog to digital input. Depending on the function selected (High, Low, Intermittent 1 thru 5, Mist, Off), the front wiper control switch connects a different set of resistors into the circuit resulting in different voltages appearing on the BCM A/D input. It should be noted that High, Low, and Mist all have the same value on this signal circuit. The second signal received from the front wiper switch is active only when the front wiper switch is in the high speed wiper position. When the wiper switch is not in the high speed position, the switch is open and the signal circuit is pulled to battery by the BCM. When the wiper switch is in the high speed position, the switch pulls the circuit low. The BCM determines how to control the Wiper high/low speed relay from this input. The third signal received from the front wiper switch is from the momentary windshield wash control switch. When the washer switch is not active the switch is open and the signal circuit is pulled to battery by the BCM. When the washer switch is active, the switch pulls the circuit low. The BCM controls the windshield wash and windshield wash activated wiper operation based on this input.

The BCM controls front wiper motor operation through two output signals and the monitoring of one input signal. The two outputs (one high side drive, one low side drive) are used to control two external wiper motor relays: front wiper motor on/off relay: which provides the wiper motor with battery power when it is activated by the high side drive signal (switched battery) from the BCM. When left deactivated, the normally closed contacts provide a ground to the wiper motor. Wiper high/low speed relay: when activated by a low side drive signal (ground) from the BCM, it switches the power supplied by the wiper motor's on/off relay to the motors high speed input. When left deactivated, the normally closed contacts connect the power supplied by the wiper motor's on/off relay to the motor's low speed input. The input used by the BCM is from the park switch located in the wiper motor assembly. When the wiper blades are not in the park position, the wiper park switch is open and the circuit is pulled up to battery by the BCM. When the wiper blades are in the park position at the bottom of the glass, the wiper park switch closes to ground pulling the park signal circuit low.

To initiate low speed operation, the BCM only energizes the front wiper motor on/off relay. This allows battery voltage from the wiper fuse to be applied through the switched contacts of the wiper motor on/off relay, through the normally closed contacts of the wiper high/low speed relay, to the low speed control circuit of the windshield wiper motor.

Redundant high speed switch pass through. The BCM provides redundant circuitry which places battery power on its wiper motor on/off relay output with activation of its low assertion high speed wiper switch input. The BCM shall be capable of doing this, even if the module has lost all microprocessor control. This redundant circuit shall supply power while in the RUN and CRANK power modes. In the CRANK power mode, the pass through shall only be active if the BCM is NOT in a computer operating properly state.

To initiate high speed operation, the BCM energizes both the front wiper motor on/off relay and the wiper high/low speed relay. This allows battery voltage from the wiper fuse to be applied through the switched contacts of the wiper motor on/off relay, through the switched contacts of the wiper high/low speed relay, to the high speed control circuit of the windshield wiper motor.

Parking the wiper motor. In order to perform an accurate read of the park switch and to ensure the wipers will come to rest while still in the park position, parking of the wipers only occurs while in a low speed wiper mode. This requires that if the wipers are performing a high speed wiper operation at the time they are required to park, the BCM shall transition the Wipers to low speed by deactivating the wiper high/low relay before attempting to park. In order to park the wipers, the BCM monitors the park circuit until the park switch pulls the park circuit to ground. At this time, the BCM will immediately deactivate the wiper motor on/off relay. The relay contacts will switch back to their normally closed position and will apply ground to the wiper motor power inputs through the normally closed contacts of the wiper high/low relay. This deactivates and dynamically brakes the wiper motor in the park position. When the wiper switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the BCM will continue to operate the motor until the wipers reach the park position. If the BCM is running the wiper motor and does not see a state transition of the park switch after 8 s, the wipers will stop immediately when the wiper switch is turned to OFF. If the ignition is turned OFF while the wipers are in mid-cycle, the wipers will stop immediately, regardless of position. The BCM will park the wipers next time the ignition is turned ON.

The windshield wiper system MIST operation is identical to LOW speed operation, except that the MIST switch is a press and release type switch. When the wiper switch is moved to the MIST position and released, low speed wiper motor operation is started and will continue until 1 cycle is complete. If the wiper switch is moved to the MIST position and held, the wiper motor will operate in the LOW speed mode until the switch is released.

Windshield wiper intermittent operation is a low speed wiper motor function with a variable delay interval between the wiper motor cycles. The duration of the delay is controlled by the front wiper control switch's intermittent 1 thru intermittent 5 settings. The wiper operation is as follows

1. The BCM will initiate a single wipe by activating its front wiper ON/OFF relay output.
2. At the completion of a single wipe, the BCM will park the wipers as described above.
3. The BCM will then pause the wipers in their park position for the time duration associated with intermittent delay switch setting.
4. When the delay time expires repeat Steps 1 and 3 until the system is turned off or taken out of intermittent mode. If the wiper switch is moved from a longer delay interval to a shorter delay interval, the BCM will command an immediate wipe cycle and reset the delay timer to the shorter delay interval.

Intermittent wiper operation may be vehicle speed sensitive. When enabled, the speed compensated intermittent feature causes the intermittent wiper delay intervals to become shorter as a function of increased speed. As vehicle speed is reduced the intervals will become closer to the predetermined

Windshield Washer System

The BCM controls the windshield wash operation and windshield wash activated wiper operation. When the BCM detects the activation of the momentary windshield wash control switch, it activates its washer pump relay drive output which supplies battery power to the coil of the washer pump relay. This energizes the relay, which switches battery power to the pump motor. The BCM will also activate continuous low speed windshield wipes as described above. Upon deactivation of the windshield wash control switch, the wiper control module (BCM) shall deactivate the wash motor and will also park the wiper motor as described above unless the drip wipe feature is enabled. On some vehicles the drip wipe feature will be enabled and cause the system to provide additional wiping of the windshield after the switch has been released and fluid is no longer being applied. The front wash feature may attempt to detect a stuck switch. When enabled, activation of the wash feature shall be limited to 10 seconds.

On vehicles with the Rear Wash feature a single reversing wash motor may be utilized for both the front and rear wash operation. In this system the wash motor is operated in one direction to spray fluid on the front windshield and then operated in the reverse direction to spray fluid on the rear window. The BCM Controls the reversing wash motor through two High Side Drive outputs. One controls the Front Wiper Motor Relay and one controls the Rear Wiper Relay.

Headlamp Washer System

When Headlamp Wash Equipped, the headlamps shall be sprayed with wash fluid as a result of an extended Windshield Wash Switch Activation. In order to preserve wash fluid, the feature shall only be allowed to activate if the Low or High Beam Headlamps are active. In addition, after the initial Headlamp Wash operation has been performed, additional headlamp washes shall not be performed for the next 4 Windshield Wash activations or for 48 hours whichever comes first. In the event that the system has detected a Stuck Front Wash Switch condition, the Headlamp Wash Feature shall be disabled.

Rain Sense Mode and Rain Sense Indicator

When this feature is activated on rain sense equipped vehicles, the wiper subsystem performs front windshield wipes according to the amount of moisture detected on the windshield. The BCM will control the wiper motor speed, as indicated above, based on wipe requests that it receives from a moisture sensor (rain sense module) which is mechanically attached to the windshield through a windshield mounted optic coupler. The system uses a master/slave configuration utilizing a local interconnect network (LIN) based serial data communication system. The BCM is designated as the master, while the rain sense module is designated the slave. As the system master, the BCM uses the LIN serial communication bus to enable or disable rain sense module operation, communicate wiper control switch settings, and wiper motor position information to the rain sense module. The rain sense module requests wiper motor function, and provides the BCM with system status and diagnostic information for diagnostic reporting. When this feature is present, the BCM uses the front wiper control switch's intermittent 1 thru intermittent 5 settings to activate the system and to act as the automatic wiper sensitivity control. This allows the driver to adjust the moisture level at which the rain Sensor requests the BCM to automatically wipe the windshield. The intermittent 1 setting corresponds to the lowest sensitivity and intermittent 5 the highest sensitivity.

Some vehicles (if calibrated) shall display an AUTO front wiper indicator when the feature is active. This indicator shall notify the driver of the vehicle that the rain sensor is ready to perform automatic wiping of the windshield upon detection of moisture.

This indicator shall be requested when all of the following are true

1. Power mode is RUN
2. If single steering column switch equipped: The front wiper switch is SENSITIVITY 1 through SENSITIVITY 5.
3. If dual steering column stalk equipped: The front wiper switch stalk angle is SENSITIVITY.

The above indicator shall be turned OFF when any of the following become true

1. Power mode becomes OFF, CRANK or ACCESSORY.
2. Front wiper switch is changed to OFF, MIST, LOW or HIGH.

Rear Wiper System

On vehicles equipped with a Rear Wiper, the BCM determines of the Rear Wipe/Wash System Mode of Operation by monitoring the multiplexed output of the Rear Wipe/Wash Switch. The Rear Wipe Wash Switch uses a reference ground signal from the BCM. The BCM provides a switched Battery pull-up for the Rear Wiper/Washer Switch output signal it receives. All the BCM inputs are recognized as active when the Rear Wiper Switch provides a path to the referenced ground signal. The Rear Wiper/Washer signal received by the BCM is the result of 3 resistors in the Rear Wiper Switch configured as a resistor ladder network. This signal is connected to a BCM Analog to Digital Input which also provides a switched Battery pull-up for the circuit. Depending on the function selected (Low, Intermittent, Off, Wash), the Rear Wiper Control Switch connects a different set of resistors into the circuit resulting in different voltages appearing on the BCM A/D input. By monitoring this voltage, the BCM determines how to control the Rear Wiper Motor Relay and the Rear Washer Relay.

The BCM Controls the single speed Rear Wiper Motor by its Active High output to the external Rear Wiper Motor Relay. When the BCM activates its output and applies Battery to the coil of the relay, the relay energizes, allowing Battery voltage from the fuse to be applied through the switched contacts of the Rear Wiper Motor Relay to the Rear Wiper Motor's control input. The motor then operates continuously at low speed. The BCM does not control the parking of the Rear Wiper Motor. It is self parking. When the BCM deactivates its output, the contacts of the Rear Wiper Motor Relay switch back to ground which will be used by the wiper for Dynamic Braking. The Rear Wiper's internal park switch and circuitry will sustain motor operation until the wiper arm has returned to its Park position.

Rear Wash

When the Body Control Module detects that the Rear wiper/wash switch has activated the momentary Wash switch, it activates a High Side Drive output which supplies Battery to the coil of the Rear Washer Pump Relay. This energizes the Relay, which switches Battery Power to the Washer Pump Motor. The BCM will also activate continuous Low Speed Windshield Wipers as described above. The BCM software will attempt to detect a stuck Rear Wash Switch. A stuck Rear Wash Switch condition is detected if the Rear Wash Motor Relay Output has been continuously active for 10 seconds or more. Upon detecting this the BCM will fail soft the state of the Rear Wash Control to Inactive. This shall cause the System to perform as if the momentary Wash control had been released.

Electrical Information Reference

1. «CIRCUIT TESTING»(ref-652238-S32451086822014082300000)
2. «CONNECTOR REPAIRS»(ref-652238-S24409892572014082300000)
3. «TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS»(ref-652238-S35849067632014082300000)
4. «WIRING REPAIRS»(ref-652238-S13433242552014082300000)

Circuit/System Verification

If this DTC is set, replace the B117 rain sensor.

Repair Instructions

Perform the DIAGNOSTIC REPAIR VERIFICATION after completing the diagnostic procedure.

1. «WINDSHIELD OUTSIDE MOISTURE SENSOR REPLACEMENT»(ref-652257-S18803831632014082300000)
2. «CONTROL MODULE REFERENCES»(ref-652232-S11179918262014082300000) for BCM replacement, setup, and programming

1. «CIRCUIT TESTING»(ref-652238-S32451086822014082300000)
2. «CONNECTOR REPAIRS»(ref-652238-S24409892572014082300000)
3. «TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS»(ref-652238-S35849067632014082300000)
4. «WIRING REPAIRS»(ref-652238-S13433242552014082300000)

Operate the rear wiper by using the S82 Windshield Wiper/Washer Switch in the continuous and the intermittent position. Verify the M45 Rear Wiper Motor activates.

Perform the DIAGNOSTIC REPAIR VERIFICATION after completing the diagnostic procedure.

1. «RELAY REPLACEMENT (ATTACHED TO WIRE HARNESS)»(ref-652238-S26621542932014082300000) «RELAY REPLACEMENT (WITHIN AN ELECTRICAL CENTER)»(ref-652238-S18364947252014082300000)
2. «REAR WINDOW WIPER MOTOR REPLACEMENT»(ref-652257-S37508483512014082300000)
3. «CONTROL MODULE REFERENCES»(ref-652232-S11179918262014082300000) for BCM replacement, programming and setup

1. «CIRCUIT TESTING»(ref-652238-S32451086822014082300000)
2. «CONNECTOR REPAIRS»(ref-652238-S24409892572014082300000)
3. «TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS»(ref-652238-S35849067632014082300000)
4. «WIRING REPAIRS»(ref-652238-S13433242552014082300000)

Perform the DIAGNOSTIC REPAIR VERIFICATION after completing the diagnostic procedure.

1. «RELAY REPLACEMENT (ATTACHED TO WIRE HARNESS)»(ref-652238-S26621542932014082300000) or «RELAY REPLACEMENT (WITHIN AN ELECTRICAL CENTER)»(ref-652238-S18364947252014082300000)
2. «CONTROL MODULE REFERENCES»(ref-652232-S11179918262014082300000) for BCM replacement, programming and setup

Headlamp Washer

The Body Control Module (BCM) controls the washer motor based on an input from the windshield wiper washer switch. The BCM monitors the washer switch through the windshield washer switch signal circuit. When the WASH switch is closed, ground is supplied to the front washer switch signal circuit. When this is seen, the BCM will command the front washer fluid pump and the low speed wipers on. When Headlamp Wash Equipped, the headlamps shall be sprayed with wash fluid as a result of an extended Windshield Wash Switch Activation. In order to preserve wash fluid, the feature shall only be allowed to activate if the main beam or dipped beam is active. In addition, after the initial Headlamp Wash operation has been performed, additional headlamp washes shall not be performed for the next 4 Windshield Wash activations or for 48 hours whichever comes first.

1. «CIRCUIT TESTING»(ref-652238-S32451086822014082300000)
2. «CONNECTOR REPAIRS»(ref-652238-S24409892572014082300000)
3. «TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS»(ref-652238-S35849067632014082300000)
4. «WIRING REPAIRS»(ref-652238-S13433242552014082300000)

Operate the headlamp washer using the S82 Window Wiper/Washer Switch. Verify the G16 Headlamp Washer Fluid Pump activates. Main beam or dipped beam is ON.

Perform the DIAGNOSTIC REPAIR VERIFICATION after completing the repair.

1. «RELAY REPLACEMENT (ATTACHED TO WIRE HARNESS)»(ref-652238-S26621542932014082300000) or «RELAY REPLACEMENT (WITHIN AN ELECTRICAL CENTER)»(ref-652238-S18364947252014082300000)
2. «CONTROL MODULE REFERENCES»(ref-652232-S11179918262014082300000) for BCM replacement, programming and setup.

Rear Washer

When the body control module (BCM) detects that the rear wiper/wash switch has activated the momentary wash switch, it activates a high side drive output which supplies battery to the coil of the rear washer pump relay. This energizes the relay, which switches battery power to the washer pump motor. The BCM will also activate continuous low speed windshield wipes as described above. This washer and wiper operation shall be continued so long as the switch remains active. Upon termination the rear wash motor will be deactivated and the wiper shall move to its park position and deactivate.

1. «CIRCUIT TESTING»(ref-652238-S32451086822014082300000)
2. «CONNECTOR REPAIRS»(ref-652238-S24409892572014082300000)
3. «TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS»(ref-652238-S35849067632014082300000)
4. «WIRING REPAIRS»(ref-652238-S13433242552014082300000)

Activate the rear washers with S80 Windscreen Wiper/Washer Switch. Check that G24 Windscreen Washer Pump is activated.

Perform the DIAGNOSTIC REPAIR VERIFICATION after completing the diagnostic procedure.

1. «RELAY REPLACEMENT (ATTACHED TO WIRE HARNESS)»(ref-652238-S26621542932014082300000) or «RELAY REPLACEMENT (WITHIN AN ELECTRICAL CENTER)»(ref-652238-S18364947252014082300000)
2. «WINDSHIELD WASHER PUMP REPLACEMENT»(ref-652257-S08179804222014082300000)
3. «CONTROL MODULE REFERENCES»(ref-652232-S11179918262014082300000) for BCM replacement, programming and setup

1. «CIRCUIT TESTING»(ref-652238-S32451086822014082300000)
2. «CONNECTOR REPAIRS»(ref-652238-S24409892572014082300000)
3. «TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS»(ref-652238-S35849067632014082300000)
4. «WIRING REPAIRS»(ref-652238-S13433242552014082300000)

Operate the front washer by using the S80 Window Wiper/Washer Switch. Verify the G24 Windshield Washer Pump activates.

Output Control Tests

Ignition ON, command the Windshield Washer Relay Command ON and OFF with a scan tool. Observe that the KR11 Windshield Washer Pump Relay clicks and the G24 Windshield Washer Pump runs.

Perform the DIAGNOSTIC REPAIR VERIFICATION after completing the diagnostic procedure.

1. «CONTROL MODULE REFERENCES»(ref-652232-S11179918262014082300000) for BCM replacement, setup, and programming
2. «RELAY REPLACEMENT (ATTACHED TO WIRE HARNESS)»(ref-652238-S26621542932014082300000) or «RELAY REPLACEMENT (WITHIN AN ELECTRICAL CENTER)»(ref-652238-S18364947252014082300000)

Symptoms - Wiper/Washer Systems

Note. The following steps must be completed before using the symptom tables

1. Perform «DIAGNOSTIC SYSTEM CHECK - VEHICLE»(ref-652232-S33658475782014082300000) , in order to verify that all of the following conditions are true: No DTCs are set. The control modules can communicate via the serial data link.
2. Refer to «WIPER/WASHER SYSTEM DESCRIPTION AND OPERATION»(ref-652257-S18209149372014082300000) in order to familiarize yourself with the system functions.

Intermittent

Faulty electrical connections or wiring may be the cause of intermittent conditions. Refer to TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS .

1. «CIRCUIT TESTING»(ref-652238-S32451086822014082300000)
2. «CONNECTOR REPAIRS»(ref-652238-S24409892572014082300000)
3. «TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS»(ref-652238-S35849067632014082300000)
4. «WIRING REPAIRS»(ref-652238-S13433242552014082300000)

1. Ignition ON, windshield wiper/washer switch in the OFF position, verify the scan tool Windshield Washer Switch parameter is Inactive.
2. If not the specified value, refer to «WASHER MALFUNCTION»(ref-652257-S39965304742014082300000) .
3. Wiper switch in the OFF position, verify the scan tool Windshield Wiper Switch parameter is Off.
4. If not the specified value, refer to the «WINDSHIELD WIPER/WASHER SWITCH CIRCUIT TEST»(ref-652257-S34581164352014082300000) .
5. Wiper switch in the OFF position, verify the scan tool Windshield Wiper High Speed Switch parameter is Inactive.
6. If not the specified value, refer to the «WINDSHIELD WIPER/WASHER SWITCH CIRCUIT TEST»(ref-652257-S34581164352014082300000) .
7. Wiper switch in the LO position, verify the scan tool Windshield Wiper Switch parameter is Low.
8. If not the specified value, refer to the «WINDSHIELD WIPER/WASHER SWITCH CIRCUIT TEST»(ref-652257-S34581164352014082300000) .
9. Wiper switch in the HIGH position, verify the scan tool Windshield Wiper High Speed Switch parameter is Active.
10. If not the specified value, refer to the «WINDSHIELD WIPER/WASHER SWITCH CIRCUIT TEST»(ref-652257-S34581164352014082300000) .
11. Wiper switch in the INT position, observe the scan tool Windshield Wiper Switch parameter while cycling the delay adjustment switch from long delay to short delay. The parameter should cycle between D1 and D5 as each delay position is selected.
12. If not the specified value, test or replace the windshield wiper/washer switch.
13. Wiper switch in the LO position, verify the windshield wipers are cycling at the low speed.
14. If the wipers are not operating at low speed, refer to the «WINDSHIELD WIPER MOTOR CIRCUIT TEST»(ref-652257-S35965129672014082300000) .
15. Wiper switch in the HIGH position, verify the windshield wipers are cycling at high speed.
16. If the wipers are not operating at high speed, refer to the «WINDSHIELD WIPER MOTOR CIRCUIT TEST»(ref-652257-S35965129672014082300000) .
17. Observe the scan tool BCM Wiper Park Switch parameter. The reading should display Active when the wipers are parked and Inactive with the wipers ON or out of the park position.
18. If the Wiper Park Switch parameter is always Active or Inactive or the wipers do not park, refer to the «WIPER PARK CIRCUIT TEST»(ref-652257-S24504478492014082300000) .

Windshield Wiper/Washer Switch

1. Disconnect the harness connector at the S82 windshield wiper/washer switch.
2. With the S82 windshield wiper/washer switch in the HIGH position, test for less than 5 ohms between the low reference terminal 2 and the signal terminal 1.
3. If greater than the specified value, replace the S82 windshield wiper/washer switch.
4. While cycling the S82 windshield wiper/washer switch through each delay and speed position, test for the specified resistance between the low reference terminal 2 and the signal terminal 3.

Note. If the switch tests open in any switch position other than OFF, test the signal circuits for a short to voltage before replacing the switch.

Wiper Switch Values

Windshield Wiper Motor

1. Ignition OFF, disconnect the harness connector at the M75 windshield wiper motor.
2. Install a 25 A fused jumper wire between the control terminal E and 12 V. Install a jumper wire between the ground terminal C and ground.
3. Verify the M75 windshield wiper motor is operating in the low speed mode.
4. If the M75 windshield wiper motor is not in the low speed mode, replace the M75 windshield wiper motor.
5. Install a 25 A fused jumper wire between the control terminal D and 12 V. Install a jumper wire between the ground terminal C and ground.
6. Verify the M75 windshield wiper motor is operating in the high speed mode.
7. If the M75 windshield wiper motor is not in the high speed mode, replace the M75 windshield wiper motor.

Perform the DIAGNOSTIC REPAIR VERIFICATION after completing the diagnostic procedure.

1. «WINDSHIELD WIPER MOTOR REPLACEMENT»(ref-652257-S35682574542014082300000)
2. «RELAY REPLACEMENT (ATTACHED TO WIRE HARNESS)»(ref-652238-S26621542932014082300000) or «RELAY REPLACEMENT (WITHIN AN ELECTRICAL CENTER)»(ref-652238-S18364947252014082300000)
3. «WINDSHIELD WIPER AND WASHER SWITCH REPLACEMENT»(ref-652257-S12462314332014082300000)
4. «CONTROL MODULE REFERENCES»(ref-652232-S11179918262014082300000) for BCM replacement, setup, and programming

1. «CIRCUIT TESTING»(ref-652238-S32451086822014082300000)
2. «CONNECTOR REPAIRS»(ref-652238-S24409892572014082300000)
3. «TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS»(ref-652238-S35849067632014082300000)
4. «WIRING REPAIRS»(ref-652238-S13433242552014082300000)

1. Ignition ON, observe the scan tool Windshield Washer Switch parameter while pressing and releasing the washer switch. The reading should change between INACTIVE and ACTIVE.
2. If the reading does not change between INACTIVE and ACTIVE, refer to «WINDSHIELD WASHER SWITCH CIRCUIT TEST»(ref-652257-S41837509462014082300000) .
3. Command the Windshield Washer Relay Command ON and OFF with a scan tool. The windshield washers should turn ON and OFF when changing between the commanded states.
4. If windhield washers do not turn ON and OFF, refer to the «WASHER PUMP CIRCUIT TEST»(ref-652257-S04308797602014082300000) .
5. Command the Rear Washer Relay Command ON and OFF with a scan tool. The rear washer should turn ON and OFF when changing between the commanded states.
6. If the rear washer does not turn ON and OFF, refer to the «WASHER PUMP CIRCUIT TEST»(ref-652257-S04308797602014082300000) .
7. If the rear washer turns ON and OFF, refer to «REAR WASHER SWITCH CIRCUIT TEST»(ref-652257-S23177113832014082300000) .
8. Command the Headlamp Washer Relay Command ON and OFF with a scan tool. The headlamp washers should turn ON and OFF when changing between the commanded states.
9. If the headlamp washers do not turn ON and OFF, refer to «HEADLAMP WASHER MALFUNCTION»(ref-652257-S36476390972014082300000) .
10. Verify the windshield washer fluid level is above the minimum level.
11. If not above the minimum level, fill the reservoir and inspect for leaks. If the low washer fluid indicator is still ON, refer to «LOW WASHER FLUID INDICATOR TEST»(ref-652257-S15993955262014082300000) .

Perform the DIAGNOSTIC REPAIR VERIFICATION after completing the diagnostic procedure.

1. «WINDSHIELD WIPER AND WASHER SWITCH REPLACEMENT»(ref-652257-S12462314332014082300000)
2. «CONTROL MODULE REFERENCES»(ref-652232-S11179918262014082300000) for BCM replacement, setup, and programming

1. «CIRCUIT TESTING»(ref-652238-S32451086822014082300000)
2. «CONNECTOR REPAIRS»(ref-652238-S24409892572014082300000)
3. «TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS»(ref-652238-S35849067632014082300000)
4. «WIRING REPAIRS»(ref-652238-S13433242552014082300000)

Ignition ON, S802 windshield wiper/washer switch in the low position. Spray water on the windshield. The windshield wipers should operate at low speed.

If the windshield wipers do not operate, refer to WINDSHIELD WIPER SYSTEM MALFUNCTION .

Rain Sensor Malfunction

1. Ignition OFF, disconnect the harness connector at the B117 rain sensor.
2. Test for less than 5 ohms between the ground circuit terminal 2 and ground.
3. If greater than the specified range, test the ground circuit for an open/high resistance.
4. Ignition ON, verify that a test lamp illuminates between B+ voltage circuit terminal 1 and ground.
5. If the test lamp does not illuminate, test the B+ voltage circuit for a short to ground or an open/high resistance.
6. If all circuits test normal, replace the B117 rain sensor.

Perform the DIAGNOSTIC REPAIR VERIFICATION after completing the diagnostic procedure.

1. «WINDSHIELD OUTSIDE MOISTURE SENSOR REPLACEMENT»(ref-652257-S18803831632014082300000)
2. «CONTROL MODULE REFERENCES»(ref-652232-S11179918262014082300000) for BCM or the Instrument Panel Cluster replacement, setup, and programming

1. «CIRCUIT TESTING»(ref-652238-S32451086822014082300000)
2. «CONNECTOR REPAIRS»(ref-652238-S24409892572014082300000)
3. «TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS»(ref-652238-S35849067632014082300000)
4. «WIRING REPAIRS»(ref-652238-S13433242552014082300000)

Verify the Rear Wiper Command parament is active when operating the rear wipers.

Rear Wiper/Washer Switch Circuit Malfunction

1. Ignition OFF, disconnect the X1 harness connector at the S82 windshield wiper/washer switch.
2. Verify that a test lamp illuminates between the low reference terminal 2 and B+.
3. If the test lamp does not illuminate, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K9 BCM.
4. Test for 10 V between the signal circuit terminal 4 and ground.
5. If less than the specified value, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K9 BCM.
6. If all circuits test normal, replace the S82 windshield wiper/washer switch.

Rear Wiper Motor Circuit Malfunction

1. Ignition OFF, disconnect the KR7 rear wiper relay.
2. Test for less than 5 ohms between the ground circuit terminal 86 and ground.
3. If greater than the specified range, test the ground circuit for an open/high resistance.
4. Test for less than 5 ohms between the ground circuit terminal 87A and ground.
5. If greater than the specified range, test the ground circuit for an open/high resistance.
6. Ignition ON, verify a test lamp illuminates between the B+ circuit terminal 87 and ground.
7. If the test lamp does not illuminate, test the rear wiper fuse for an open. If the fuse is open, test the control circuit terminal 30 for a short to ground.
8. Verify that a test lamp does not illuminate between the control circuit terminal 30 and ground.
9. If the test lamp illuminates, test the control circuit for a short to voltage.
10. Connect a test lamp between the control cirucit terminal 85 and ground.
11. Command the rear wiper ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
12. If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the K9 BCM.
13. If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, test or replace the K9 BCM.
14. Ignition OFF, disconnect the connector at the M45 rear wiper motor.
15. Test for less than 5 ohms between the ground circuit terminal C and ground.
16. If greater than the specified range, test the ground circuit for an open/high resistance.
17. Ignition ON, verify a test lamp illuminates between B+ circuit terminal B and ground.
18. If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
19. Connect the harness connector at the M45 rear wiper motor.
20. Connect a 3 A fused jumper wire between the control circuit terminal 30 and B+. Verify the rear wiper motor is activated.
21. If the rear wiper motor does not activate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, test or replace the M45 rear wiper motor.
22. If all circuits test normal, test or replace the KR7 Rear Wiper Relay.

Perform the DIAGNOSTIC REPAIR VERIFICATION after completing the diagnostic procedure.

1. «CONTROL MODULE REFERENCES»(ref-652232-S11179918262014082300000) for BCM replacement, programming and setup.
2. «RELAY REPLACEMENT (ATTACHED TO WIRE HARNESS)»(ref-652238-S26621542932014082300000) or «RELAY REPLACEMENT (WITHIN AN ELECTRICAL CENTER)»(ref-652238-S18364947252014082300000)
3. «REAR WINDOW WIPER MOTOR REPLACEMENT»(ref-652257-S37508483512014082300000)
4. «WINDSHIELD WIPER AND WASHER SWITCH REPLACEMENT»(ref-652257-S12462314332014082300000)

1. «CIRCUIT TESTING»(ref-652238-S32451086822014082300000)
2. «CONNECTOR REPAIRS»(ref-652238-S24409892572014082300000)
3. «TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS»(ref-652238-S35849067632014082300000)
4. «WIRING REPAIRS»(ref-652238-S13433242552014082300000)

Perform the DIAGNOSTIC REPAIR VERIFICATION after completing the diagnostic procedure.

1. «RELAY REPLACEMENT (ATTACHED TO WIRE HARNESS)»(ref-652238-S26621542932014082300000) or «RELAY REPLACEMENT (WITHIN AN ELECTRICAL CENTER)»(ref-652238-S18364947252014082300000)
2. «HEADLAMP WASHER PUMP REPLACEMENT»(ref-652257-S10637639022014082300000)
3. «WINDSHIELD WIPER AND WASHER SWITCH REPLACEMENT»(ref-652257-S12462314332014082300000)
4. «CONTROL MODULE REFERENCES»(ref-652232-S11179918262014082300000) for BCM replacement, setup, and programming

Correction

1. 01 - Replacement
2. 02 - Removal - Refit
3. 03 - Renovate
4. 04 - Paint
5. 05 - Adjust
6. 06 - Change comp. unit
7. 07 - Lubricate - Clean - Polish
8. 08 - Check/Fault search
9. 09 - Expose
10. 10 - Install new
11. 11 - Transfer