Home ReviewsRefund
Home/Pontiac/Vibe/Pontiac Vibe I рестайлинг (2002-2008)/Repair manual/Automatic Trans/Shift Interlock System: Removal & Installation
Contents Section: Automatic Trans All sections

Shift Interlock System: Removal & Installation Pontiac Vibe I рестайлинг

Automatic Trans ~554 words

Removal Procedure

  1. Remove the bezel. Refer to «Bezel Replacement - Instrument Panel (I/P) Cluster»(ref-200060-S07970655812005102000000) in Instrument Panel, Gages, and Console.
  2. Remove the steering column trim covers. Refer to «Steering Column Trim Covers Replacement»(ref-200097-S20519248972005102000000) in Steering Wheel and Column.
  3. Remove the instrument panel trim panel. Refer to «Trim Panel Replacement - Instrument Panel (I/P) Center»(ref-200060-S03408358402005102000000) in Instrument Panel, Gages, and Console.
  4. Remove the front floor trim plate. Refer to «Trim Plate Replacement - Front Floor Console»(ref-200060-S06612301992005102000000) in Instrument Panel, Gages, and Console.
  5. Remove the front floor console cover. Refer to «Console Replacement - Front Floor»(ref-200060-S04842339792005102000000) in Instrument Panel, Gages, and Console.
  6. Disconnect the park lock cable from the shift lock lever.
  7. Disconnect the park lock cable from the shift lever plate.
  8. Disconnect the cable clamp.
  9. Turn the ignition switch to the ACC or Run position.
  10. Using a screwdriver, disconnect the cable from the upper bracket.
  11. Turn the ignition switch to the OFF position.

Installation Procedure

  1. Turn the ignition switch to the ACC or RUN position.
  2. Connect the cable to the upper bracket.
  3. Connect the cable clamp.
  4. Shift the manual selector to Neutral.
  5. Using a small screwdriver, unlock the lock tab on the cable adjustment assembly (1).
  6. Install the park lock cable through the hole of the shift lever plate, then press the retainer into the shift lever plate.
  7. Connect the park lock cable to the shift lock lever.
  8. Ensure that the ignition switch is in the ACC or RUN position and the manual lever is in the Neutral position.
  9. Press the lock tab on the cable adjustment assembly.
  10. Check park lock cable for proper operation.
  11. Install the front floor console cover. Refer to «Console Replacement - Front Floor»(ref-200060-S04842339792005102000000) in Instrument Panel, Gages, and Console.
  12. Install the front floor trim plate. Refer to «Trim Plate Replacement - Front Floor Console»(ref-200060-S06612301992005102000000) in Instrument Panel, Gages, and Console.
  13. Install the instrument panel trim panel. Refer to «Trim Panel Replacement - Instrument Panel (I/P) Center»(ref-200060-S03408358402005102000000) in Instrument Panel, Gages, and Console.
  14. Install the steering column trim covers. Refer to «Steering Column Trim Covers Replacement»(ref-200097-S20519248972005102000000) in Steering Wheel and Column.
  15. Install the bezel. Refer to «Bezel Replacement - Instrument Panel (I/P) Cluster»(ref-200060-S07970655812005102000000) in Instrument Panel, Gages, and Console.
  1. Disconnect the negative battery cable. Refer to «Battery Negative Cable Disconnect/Connect Procedure»(ref-200056-S05052159252005102000000) in Engine Electrical.
  2. Remove the front floor console. Refer to «Console Replacement - Front Floor»(ref-200060-S04842339792005102000000) in Instrument Panel, Gages and Console.
  3. Disconnect the electrical connector (1).
  4. Remove the retaining screw, then the Shift Lock Control Module/Shift Lock Solenoid assembly.
  1. Install the Shift Lock Control Module/Shift Lock Solenoid assembly, then the retaining screw (2).
  2. Connect the electrical connector (1).
  3. Install the front floor console. Refer to «Console Replacement - Front Floor»(ref-200060-S04842339792005102000000) in Instrument Panel, Gages and Console.
  4. Connect the negative battery cable.
  1. Disconnect the negative battery cable. Refer to «Battery Negative Cable Disconnect/Connect Procedure»(ref-200056-S05052159252005102000000) in Engine Electrical.
  2. Remove the front floor console. Refer to «Console Replacement - Front Floor»(ref-200060-S04842339792005102000000) in Instrument Panel, Gages and Console.
  3. Disconnect the electrical connector (1).
  4. Remove the retaining screw, then the Shift Lock Control Module/Shift Lock Solenoid assembly.
  1. Install the Shift Lock Control Module/Shift Lock Solenoid assembly, then the retaining screw (2).
  2. Connect the electrical connector (1).
  3. Install the front floor console. Refer to «Console Replacement - Front Floor»(ref-200060-S04842339792005102000000) in Instrument Panel, Gages and Console.
  4. Connect the negative battery cable.

More articles — Shift Interlock System